Installation Guide

ManualsBrandsSERENE VALLEY ManualsDrop-in Kitchen SinksStainless Steel 33-in. Single Bowl Drop-in or Undermount Kitchen Sink with Thick Deck and Grid, DS3322R

NOTE: Specialized tools may be necessary to install Stainless Steel Kitchen sinks with

countertop materials other than wood, marble or granite.

The step-by-step guidelines in the installation instructions are a general reference for installing your new sink. It is

recommended to install the sink by hiring a licensed professional.

Tools you will need:

Prior to Installation:

• Make sure that you have all necessary parts by checking the parts list. If

any part is missing or damaged, please contact Customer Service.

• Inspect the sink prior to installation to make sure that it has not been

damaged or during shipping

• Use the cut-out template provided

• Observe all plumbing and building codes according to your state

requirements

Safety Goggles

Silicone Adhesive

Jig Saw

Phillips Screwdriver

Putty Knife

Tape Measure

Pencil

Scissors

Screwdriver

Drill

INSTALLATION MANUAL

Stainless Steel Dual Mount Kitchen Sinks

DDG3622R，DD3321R，DD3322R，DS3222RR，

DS2522R，DS3322R，DS3622R，DDK3322R，

DD3622R，DDK3622R

Summary of content (12 pages)

PAGE 1
INSTALLATION MANUAL Stainless Steel Dual Mount Kitchen Sinks DDG3622R，DD3321R，DD3322R，DS3222RR， DS2522R，DS3322R，DS3622R，DDK3322R， DD3622R，DDK3622R Prior to Installation: • Make sure that you have all necessary parts by checking the parts list. If any part is missing or damaged, please contact Customer Service.
PAGE 2
Top Mount Installation Step 1. Position Template • Check the cut-out template against the actual sink to ensure a proper sized cut-out. • Place the cut-out template in the desired location on the countertop. NOTE: Make sure clearance is suitable for backsplash, faucet and plumbing for the sink. Step 2. Trace Template • 2 Trace template on countertop with a pencil.
PAGE 3
Step 3. Cut Countertop • Cut the opening in the countertop by carefully following the traced line. NOTE: Please use the appropriate saw that best fits your countertop material.
PAGE 4
Step 4. Attach Mounting Hardware • • Attach mounting hardware to the prongs protruding from the underside of the sink rim. Make sure the hooked side of the mounting clip is facing away from the sink. NOTE: Maximum countertop thickness for Top Mount installation is 1 1/2". Push Step 5. Apply Silicone or Plumber's Putty • • 4 Clean and dry the surface around the opening of the sink. Turn the unit upside down to apply sealant. Apply siliconebased sealant (not included) underneath the edge of the sink.
PAGE 5
Step 6. Secure Sink to Countertop • • • • Insert the sink into the opening, check the alignment of the sink to the cutout in the countertop and press firmly. Tighten the screws in the front of the sink, followed by the ones in the back and on the sides of the sink. Remove excess silicone-based sealant. Allow sealant to set for 30-60 minutes.
PAGE 6
Step 7. Install Plumbing Fixtures • • Connect drain to sink. Connect trap to drain. Connect water supply connections to faucet according to manufacturer's instructions. Run water into sink and check for leaks. Maintenance Clean your sink on a regular basis with warm soapy water. Rinse the sink after using cleaning products. Wipe the sink surface with a soft cloth to remove any liquid residue. Do not cut food directly on the surface of the sink.
PAGE 7
Undermount Installation Step 1.
PAGE 8
Step 2. Position template • Check the cut-out template against the actual sink to ensure a proper sized cut-out. • Place the cut-out template in the desired location on the countertop. NOTE: Make sure clearance is suitable for backsplash, faucet and plumbing for the sink. Step 3. Trace Template • 8 Trace template on countertop with a pencil.
PAGE 9
Step 4. Cut Countertop • Cut the opening in the countertop by carefully following the traced line. NOTE: Please use the appropriate saw that best fits your countertop material. Step 5. Set up mounting brackets • Turn countertop over and align sink with countertop. Decide location for mounting brackets. • Mounting holes should be 1/2" from edge of sink.
PAGE 10
Step 6. Drill hole in countertop 3/8 • Drill 3/8" diameter x 1/2" deep hole in the countertop. • Insert anchors into drilled holes and lightly tap with a hammer until flush. 1/2 Step 7.
PAGE 11
Step 8. Secure sink to countertop • Use a bead of silicone (or preferred adhesive) around the rim of the sink. Check the alignment of the sink to the cutout in the countertop. Place sink over cutout hole and press firmly. Step 9. Attach mounting hardware • • Attach mounting hardware to secure bowl. Remove excess sealant from inside lip. Allow sealant to set for 30 - 60 minutes. NOTE: Use acetone or rubbing alcohol to remove any excess sealant.
PAGE 12
Step 10. Install Plumbing Fixtures • • Connect drain to sink. Connect trap to drain. Connect water supply connections to faucet according to manufacturer's instructions. Run water into sink and check for leaks. Maintenance Clean your sink on a regular basis with warm soapy water. Rinse the sink after using cleaning products. Wipe the sink surface with a soft cloth to remove any liquid residue. Do not cut food directly on the surface of the sink.