User`s manual

36
English
79. TECHNICAL INFORMATION
Handset
•Amplied dB level (Amplify off):
0 to 15 dB in 5 steps
•Amplied dB level (Amplify on):
35 to 50 dB
•Tone control settings: 4
settings - T1, T2, T3, T4 (high
tone)
•Display Language: English,
French, Spanish
•Handset Talking Voice: English
(in both English and Spanish
modes), French
•Handset battery life:
Approximately 80 hours
Telephone Answering Machine
(TAM)
•Maximum recording time: 22
minutes
•Maximum # of messages &
memo: 50
•Maximum length of each
message / memo: 3 minutes
•# of Playback speed: 3
(Normal, Slow 1, Slow 2)
•New message audio alert: Yes
(beeps once every 30 seconds)
•TAM volume loudness level: 1
to 9
•Speakerphone in both base and
handset: Yes
•Number of rings before
answering: 2, 3, 4, 5, 6, SA (Toll
Saver)
•# of OGM: 2
•Maximum length of OGM
recording: 30 seconds
•Remote Access code: Yes
(default is “0000”)
•TAM Voice prompts: English,
French, Spanish
•TAM battery backup option:
Yes
•(requires user provided 4 AAA
size NiMH
•Rechargeable batteries; good
for ~3 hours)
Dimensions
•Handset size: 7.0” x 2.1” x 1.2”
•Base size: 6.7” x 3.1” x 5.0”
Weight
•Handset weight: 5.7 oz.
•Base weight: 16 oz.
Temperature range:
•Operating: 0 to 30°C
•Storage: -10 to 40°C
Power requirements:
•AC Adapter: UL listed 7.5vdc,
500 ma
•Base battery: 4 x AAA size
NIMH (optional and are
provided by user)
•Handset battery: 2 x AAA size
NIMH (included)
Note: Specications are subject
to change without any notice.
80. TROUBLE SHOOTING
Q1: Base Charging Indicator
is not on when handset is
placed on the base.
Ans: Move the handset slightly
to make better contact.
Q2: No CID information on an
incoming call.
Ans: Check your subscription
with your phone company.
Q3: No Dial tone.
Ans: Check AC adapter and
phone cord connection.
Make sure you’re not too
far from the base. If this is
a new handset, you must
register it to the base before
using.
Q4: When I press the key,
the handset just beeps but
there is no dial tone.
ANS: The handset probably lost
sync with the base. Press
and hold the key for 5
seconds to turn off the
handset power, and then
repeat to turn back on the
power. They should sync up
in about 5 – 30 seconds.
Q5: No display on handset.
Ans: Verify battery is OK; make
sure the handset is not
power-off.
Q6: Handset asher works but
handset does not ring.
Ans: Verify handset ringer volume
is not set at minimum; verify
“Non-Disturb” is not active.
Q7: Why is the red asher
always blinking?
Ans: This indicates you have
voice mail waiting in your
provider’s voice mail server.
Or, you have missed a call;
reviewing incoming call list
clears this indicator.
Q8: Static noise on the line.
Ans: Your phone may be
located near
a touch lamp, microwave, or
other appliance, If you have
a DSL computer modem
service, make sure you have
installed a DSL lter to block
the DSL noise.
Q9: How do I turn off the
talking keypad feature?
Ans: Open the battery
compartment and slide the
lower switch to its left or
OFF.
Q10: My phone display says
“HS locked” when I try to
dial or press any key.
Ans: Your phone is locked
because key was pressed
and held too long. To
unlock phone, just press and
hold key down for about
5 seconds.
Q11: Why is the base beeps
once every 30 seconds.
Ans: You have set the New
Message Audio Alert to
on and it beeps because
you have new messages in
your answering machine.