User`s manual

32
English
“AUDIO SETTING”.
4. Press or key and to
scroll to ”RING SETUP”.
5. Press key and the screen
displays “INT RING”.
6. Press or to display
either “INT RING” or “EXT
RING”.
(INT RING means setting the
internal intercom ringer.)
(EXT RING means setting the
external incoming call ringer.)
70. EXTERNAL INCOMING CALL
RINGER
1. While “EXT RING” is shown,
press to select.
2. Press key and the screen
displays “MELODY”.
3. Press key and the screen
displays the current ringer and
sound the current ringer, such
as “MELODY 1”.
4. Press or key to scroll
to different ringer melody (ten
different ringer sounds are
available)
5. After selecting the ringer
sound, press key to
conrm and the screen
displays “MELODY” again.
6. Press or to display
“VOLUME”.
7. Press key and the screen
displays current volume of
ring tone, such as “VOLUME
3”
8. Press or to scroll to
different ring volume (5 levels)
9. Press key to conrm the
new selection on display. A
sound of “di du” indicates a
successful selection.
10. Press key to exit to standby
mode
71. INTERCOM RINGER
1. While off-line, press key
and it displays “CALL LOG”.
2. Press or key to scroll to
“HS SETTINGS.
3. Press key to conrm and it
displays “AUDIO SETTING”
4. Press or key to scroll to
”RING SETUP”.
5. Press key and the screen
displays “INT RING”.
6. Press key to conrm
and the screen displays
“MELODY”.
7. Press key and the screen
displays the current ringer and
sound the current ringer, such
as “MELODY 1”
8. Press or key to select
different ringer (ve different
internal ringer sounds)
9. After selecting the ringer
sound, press key to
conrm and the screen
displays “MELODY” again.
10. Press or to scroll to
“VOLUME”.
11. Press key and the screen
displays current volume of
ring tone, such as “VOLUME
3”
12. Press or to select the
proper ring volume (5 levels)
13. Press key to conrm the
new selection and a sound of
“di du” indicates a successful
selection.
14. Press key to exit to standby
mode
72. KEYPAD TONE AND WARNING
TONE SETTING
1. While off-line, press key
and the screen displays
“CALL LOG”.
2. Press or key to scroll to
“HS SETTINGS”.
3. Press key to conrm.
4. Press or key to scroll to
“TONE SETUP”.
5. Press key to conrm.
6. Press or to display
either “KEY TONE”,
“BATTERY LOW” or “RANGE
ALARM”
Key Tone select
7. While “KEY TONE” is shown,
press key and the screen
displays either “ON” or “OFF”.
8. Press or to display
“ON”
9. Press key to conrm and
the screen displays “KEY
TONE” again.
10. Press key to exit to off-line.
Battery Low Warning Tone
Detailed setting step is similar to
that of setting the KEY TONE.
(Note: While talking, there will be
a “di” sound when the battery
is low if the this ALARM is set
to ON. While off-line, there will
be no alarm sound; only battery
capacity symbol is displaying on
screen.)
Out-Of-Range Warning Tone
Detailed setting step is similar to
that of setting the KEY TONE.
(Note: While talking, there will
be a long “di” sound when the
handset is out-of-range from the
base if the RANGE ALARM is set
to ON.)
73. FORWARD AN INCOMING CALL
FROM HANDSET 1 TO HANDSET 2
1. On Handset 1, press
PAGE
key and then press “2” on the
keypad. This pages Handset
2 while putting the outside call
on HOLD.
2. When Handset 2 rings, press
TALK
key on Handset 2 to
answer the page.
3. Over the intercom, tell
Handset 2 that an outside call
is waiting.
4. Press key on Handset 1
to transfer the call and then
press key on Handset 1 to
exit.
(Note: If within 30 seconds
there is no answer, the call will
ring back to Handset 1.)
74. CONFERENCE CALL
This allows two handsets
conferencing with the incoming
caller.