xCAM User’s Guide
Table of Contents CHAPTER 1 INTRODUCTION.............................................................................................. 1 Overview ............................................................................................................................ 1 Physical Details - xCAM ................................................................................................... 2 Physical Details - XW3 ..........................................................................................
Chapter 1 Introduction 1 This Chapter provides information of the xCAM's features, components and capabilities. Overview Congratulations on the purchase of your new xCAM. The xCAM is a True Day/Night IP camera that features high definition 1280 x 720p video resolution and 802.11n WiFi connectivity. Features • Standalone Design. The xCAM is a standalone system with built-in CPU and Video • Dual Video Compressions. The xCAM supports H.264 and MJEPG video for different encoder.
Physical Details - xCAM Front - xCAM Figure 1: Front Panel IR LEDs IR LEDs provide illumination at night or in a dark environment. Lens No physical adjustment is required or possible for the lens, but you should ensure that the lens cover remain clean. The image quality is degraded if the lens cover is dirty or smudged. POWER indicator (Blue/Yellow) On (Blue) - The xCAM is paired. Flashing (Blue) - The xCAM is connected to router but not paired.
Rear - xCAM Figure 2: Rear Panel RJ-45 Jack This RJ-45 connector is used for power connection when the camera is under wireless mode. A customized PoE (Power over Ethernet) splitter, as a Y-cable, is provided to allow connection to PC for setup and pairing. Reset Button This button has two (2) functions: • Reboot. When pressed and released, the xCAM will reboot (restart). • Clear All Data. This button can also be used to clear ALL data and restore ALL settings to the factory default values.
Physical Details - XW3 XW3 LAN Port To be connected to the RJ-45 jack of xCAM for power feed and data exchange. Reset Button This button has the following function: • Reset to manufacturer default valued and reboot. When pressed and held over 10 seconds, the settings of the XW3 will be set to their default values. WPS Button Push the WPS button on the device and on your other wireless device to perform WPS function that easily creates an encryptionsecured wireless connection automatically.
Package Contents The following items should be included in the package: If any of these items are damaged or missing, please contact your dealer immediately.
Chapter 2 Basic Setup 2 This Chapter provides information on how to install and configure the xCAM. System Requirements • To use the Wireless interface on the wireless model, other Wireless devices must be compliant with the IEEE802.11n, IEEE802.11b or IEEE802.11g specifications. All Wireless stations must use compatible settings. Mode: Infrastructure SSID: ANY Wireless Security: Disabled Domain: USA Channel No.
6. Install the xCAM. Figure 3: Camera Installation a. Connect the provided Y-cable to the XW3 and the Home Gateway. b. Use the xCAM pigtail Ethernet RJ-45 to connect the LAN port of Y-cable. The wireless and wired modes cannot work simultaneously. It is recommended to first configure the wireless settings of an xCAM using wired mode. After configuration, disconnect the wire and power, and power on the xCAM again. Then, it will be ready for wireless operation. c.
Physical Installation Figure 4: Installation 1. Move the xCAM to where it is to be placed. 2. Connect the Ethernet cable to the LAN port of the xCAM and XW3. 3. Check and make sure that the Power LED is on.
Wall Mounting *Note: Please make sure that the xCAM is configured and added to the network before permanent mounting. 1. Use the electric drill for boring two holes in the desired position where you would like to install the xCAM. 2. Screw the two anchors into the holes of the wall. 3. Attach the xCAM to the wall and secure it with the two screws.
Note: The following steps are recommended: a. Mount the camera with the screw first. b. Adjust the angel by moving the opening of the stand. Install the other screw after the adjustment. 4. Ensure that the xCAM is secured firmly.
Appendix A Specifications A Spec xCAM Model xCAM Dimensions 76.8mm (W) x 76.8mm (H) x 38.6mm (D) (without stand) Operating Temperature 0° C to 40° C Video compression H.
Regulatory Approvals FCC Statement This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
