User's Manual

ManualsBrandsSercomm ManualsElectronicsZigBee Smoke Alarm

SZ-SMK02-US ZigBee SMOKE ALARM Installation Guide

The SZ-SMK02-US is a Smoke Alarm that is designed to detect smoke, which maybe a signal of a fire. This device can provide

more time by making alarms for you and your family to escape before a fire spreads. SZ-SMK02-US built-in a ZigBee module to

monitor battery status and will send message when battery capacity is low. Low battery message will be transmitted to a ZigBee

HA 1.2.1 certified coordinator.

Specification

Batter Type

3V lithium battery

(Duracell)DL123A

(Panasonic)CR123A

Operating Temperature

0 C to 50 C (31° - 122°F)

Operating Humidity

10% to 85% Non-condensing

Alarm Audibility

At least 85 dB at 3 meters

Dimention

120mm (diameter) x 53mm (depth)

Package Contents

LEDs

 Stand-by Mode: The device is under normal operation if the red LED flashes once for 344 seconds. When the device senses

smoke, the red LED will flash continuously and rapidly while sounds an audible alarm with 3 beeps, pause and 3 beeps.

 Low Battery Mode: The red LED flashes and the device begins to chirp once in 43 seconds. This warning should last for up

to 30 days. Please replace the battery before power is running out to secure your protection.

 Malfunction (Error) Mode: The yellow LED flashes 3 times and the device generates 3 beeps within 43 seconds. This

indicates the device is malfunctioned and needs to be repaired or serviced.

 Tamper Mode: When the device is removed from bracket, it will generate 3 beeps and the yellow LED is steadily on. The

detector will also be alarmed if it is not mounted into the bracket properly within 5 minutes after the battery is installed.

Summary of content (6 pages)

PAGE 1
SZ-SMK02-US ZigBee SMOKE ALARM Installation Guide The SZ-SMK02-US is a Smoke Alarm that is designed to detect smoke, which maybe a signal of a fire. This device can provide more time by making alarms for you and your family to escape before a fire spreads. SZ-SMK02-US built-in a ZigBee module to monitor battery status and will send message when battery capacity is low. Low battery message will be transmitted to a ZigBee HA 1.2.1 certified coordinator.
PAGE 2
Intallation Battery Installation/Replacement 1. 2. 3. 4. Open the battery cover of the device. Install the supplied battery correctly. Close the battery cover. Install the bracket. Note: you will hear a chirp after install the bracket which indicates the device is receiving battery power. Recommended Battery Operation  Please use a CR123A 3V battery. Use of a different battery may cause a detrimental effect on alarm operation.  Low temperature will reduce the battery life.
PAGE 3
Do not place the device in the following areas:  Combustion particles are the by-products of something that is burning. Thus, in or near areas where combustion particles are present you do not install the smoke alarms to avoid nuisance alarms, such as kitchens with few windows or poor ventilation, garages where there may be vehicle exhaust, near furnaces, hot water heaters, and space heaters.
PAGE 4
Wall Mounting 1. 2. 3. 4. 5. 6. Draw a six inches horizontal line at the place where you are going to install the device. Rotate the mounting bracket counterclockwise to remove it from the device. Draw 2 marks to locate the screws. Drill two holes at the marks and insert screws and wall plugs. Attach the bracket to the wall by using the supplied two screws and wall plugs. Attach the device onto the mounting bracket and turn it clockwise to fix it into place.
PAGE 5
3. Test/Silence Button The Test button is used to test if the device is working properly and mute the SZ-SMK02-US during alarm.  Test Press the Test button for about 3 seconds until it alarms. The device will generate 3 beeps, pause and 3 beeps. While the Alarm (red) LED will flash continuously and rapidly.  Silence If the device is alarming, press the Test button will have it silenced. If the smoke still remains after 10 minutes, the device will alarm again.
PAGE 6
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.