Product Info

ManualsBrandsSercomm ManualsElectronicsRF Core Module

RCM-AD-A

The product supports LoRaWAN class A operation which is a simplex transmission or reception

capability. The reception capability is time-limited per the LoRaWAN protocol, in order to save

battery consumption.

Listed below are the main performance characteristics:

Features

Description

NFC

Read device version information

Modulation

LoRa

BLE

Bluetooth 5

NFC

Passive receiver 13,56MHz AM ISO/IEC 15693 Range

distance :1cm

FUOTA

FUOTA Capable (with MachineQ client)

Protocol

LoRaWAN v1.03

Frequency band

902-928MHz and 2.4-2.5GHz ISM Band

Activation

OTAA and ABP

Max Output power

+22Bm conducted

Microprocessor

nRF52840

Memory

ProgFlash 1MB

RAM 256 kB

Transceiver

SX1262

RF Sensitivity

SF7/500Khz: -120dBm

SF12/500Khz: -129 dBm

Sensitivity (conducted)

SF7/125kHz: better than -118dBm

SF12/125kHz: better than -131dBm

SF7/250KHz:+3dBr

SF12/250KHz:+3dBr

SF7/500KHz:+6dBr

SF12/500KHz:+6dBr

FSK /50kbps: better than -109dBm

Operating temperature

From -40°C to +60°C non-condensing,

Mechanical dimensions (in millimeters)

L 20.8 mm x W 24.4 mm x H 3.6 mm

Operating Temperature

Range : -40°C to + 60°C

Summary of content (8 pages)

PAGE 1
RCM-AD-A The product supports LoRaWAN class A operation which is a simplex transmission or reception capability. The reception capability is time-limited per the LoRaWAN protocol, in order to save battery consumption. Listed below are the main performance characteristics: Features Description NFC Modulation BLE NFC Read device version information LoRa Bluetooth 5 Passive receiver 13,56MHz AM ISO/IEC 15693 Range distance :1cm FUOTA Capable (with MachineQ client) LoRaWAN v1.03 902-928MHz and 2.4-2.
PAGE 2
RF matching diagram BLE antenna (U8) is chip antenna for BLE, and its RF trace is 50ohm strip-line from module to antenna. C2 and L4 are BLE antenna matching components. Ipex connector(U10) is for NFC antenna, and RF trace NFC1 has to be close to NFC2. C106 and C107 are NFC antenna matching components. C105 and C108 are the RF filter for reducing BLE harmonic. Lora antenna(ANT1) is primary antenna and carries TX and RX signals. Total RF path in Lora is 50ohm strip-line from module to antenna.
PAGE 3
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 4
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This module is intended for OEM integrators only.
PAGE 5
OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product.
PAGE 6
Industry Canada statement: This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
PAGE 7
This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed and operated with greater than 20cm between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
PAGE 8
End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed and operated with greater than 20cm between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 5604A-RCM0”. Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un appareil où l’antenne peut être installée et utilisée à plus de 20 cm entre l’antenne et les utilisateurs.