Waterproof HD IP Camera Setup Guide Document Version: 1.0 Copyright 2017. All Rights Reserved. All trademarks and trade names are the properties of their respective owners.
Package Contents The following items should be included: If any of these items are damaged or missing, please contact your service provider immediately. 1. Waterproof HD IP Camera x 1 2. Stand x 1 3. Screw Terminal Adapter x 1 4. Screw/Anchor x 2 5. DC In Rubber x 1 6. Rubber Cap x 1 7.
Chapter 1 Introduction 1 This Chapter provides details of the Waterproof HD IP Camera's features, components and capabilities. Overview The Waterproof HD IP Camera has an Integrated Microcomputer and a high quality Mega Pixel Omni Vision CMOS Sensor, enabling it to display high quality live streaming video over your wired LAN, the Internet, and for the Waterproof HD IP Camera, an 802.11N Wireless LAN. Using enhanced H.
Features Standalone Design. The Waterproof HD IP Camera is a standalone system with built-in CPU and Video encoder. It requires only a power source and a connection to your LAN or Wireless LAN. Dual Video Support. The Waterproof HD IP Camera can support H.264 and MJEPG video for different image compression. Suitable for Home, Business or Public Facilities.
2 Chapter 2 Basic Setup This Chapter provides details on how to install and configure the Waterproof HD IP Camera. System Requirements To use the Wireless interface on the wireless model, other Wireless devices must be compliant with the IEEE802.11b, IEEE802.11g, or IEEE802.11n specifications. All Wireless stations must use compatible settings. Physical Details - Waterproof HD IP Camera Front Panel - Waterproof HD IP Camera Figure 2: Front Panel 1.
Rear Panel - Waterproof HD IP Camera Figure 3: Rear Panel 1. DC Power Input Connect the supplied 12V/1.5A power adapter here. Do not use other power adapters; doing so may damage the camera. 2. WPS/Reset Button This button has two functions: 1. WPS. Push the WPS button on the device and on your other wireless device to perform WPS function that easily creates an encryption-secured wireless connection automatically. WPS Pin Code Mode.
4. Network/Wireless LED (Green, Amber) On (Green) - Network (Wireless or LAN) connection is available. Off - Wireless or LAN is not connected or camera is not sending/receiving data. Blinking (Green) - Data is being transmitted or received via the LAN or Wireless connection. On (Amber) - If the LED is on for 5 seconds and then off, the WPS function is failed. Blinking (Amber) - WPS function is being processed. 5. Micro SD Card Slot Insert the SD card into the slot for additional storage if needed. 6.
Set up of Waterproof HD IP Camera 1. Assemble the Camera Attach the Camera Stand to the camera. Note: Due to the wide angle IR illumination and over exposure engine algorithm, please make sure that field of view produced by the camera doesn't cover the foreground object, such as table top or side wall. It is recommended to place the camera close to the edge of table top or tilt the camera away from side wall, to get the best video quality of the target at night. 2.
Wireless Connection Press the WPS button on the camera for 3-5 seconds and on your other wireless device as well to establish a wireless connection automatically. The wireless connection is successful when the Network/WPS LED (green) remains on. 3. Power Up Use only the power adapter provided. Using a different one may cause hardware damage. a. Run the AC Wire to the spice connector. b. Screw the red wire onto the positive (+) terminal of the terminal adapter. c.
*Note: The operating temperature of power adapter is 0C to 40C. Please ensure the power adapter is indoor usage. 4. Check the LEDs The Power LED will turn on briefly, then start blinking. It will blink during startup, which will take 55 to 57 seconds. After startup is completed, the Power LED should remain ON. The Network/WPS LED should be ON. Micro SD Card Installation 1. Remove the screw with a proper screwdriver, and then take the SD card cover out the camera. 2.
* Optional: Mounting the Waterproof HD IP Camera *Note: Please ensure camera is configured and added to the network before permanent mounting. Mount the Camera Mounting Suggestion Place the camera in a location near a power source. For mounting on a wall, please use the provided mounting plate. To get the best video quality for targets at night, make sure that the camera’s field of view does not include a large foreground object, such as tabletop or side wall.
1. Identify the location for mounting the camera. 2. Align the two mounting holes at the bottom of the camera stand with the two screws, and mount the mounting plate onto the screws. 3. Screw/attach the camera onto the camera stand. 4. There are two methods for Internet connection: Connect a USB to RJ-45 cable (Optional) to the USB port of the Wireless IP Camera. Then use a standard LAN cable to connect an available port on your router.
5. Connect the power cable into the back of the camera and then insert the rubber cap. Caution: Make sure the rubber cap is attached seamlessly and well-positioned to the camera so the water will not get into the camera. 6. Plug the adapter end into a power outlet. 7. Adjust the Wireless IP Camera to a desired position and secure it firmly.
Appendix A Specifications A Waterproof HD IP Camera Model Waterproof HD IP Camera Dimensions 76mm (W) x 76mm (H) x 48.6mm (D) (without stand) Operating Temperature -40 C to 50 C (Cold Start: -40ºC; Heater mode: -40ºC to 0ºC) Video compression H.
-Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
