NA502S Multiple RF Home Gateway User Guide i
Table of Contents CHAPTER 1 INTRODUCTION .............................................................................................. 1 Package Contents .............................................................................................................. 1 Features .............................................................................................................................. 1 LEDs .....................................................................................................
Chapter 1 Introduction 1 This Chapter provides an overview of the Multiple RF Home Gateway's features and capabilities. Congratulations on the purchase of your new Multiple RF Home Gateway. The Multiple RF Home Gateway is a consumer electronic device, which is designed to bridge all appliances of your home, from IP cameras to sensors, and allow you to monitor and manage them over the Internet. Most of the devices can be paired with the gateway via a single button push.
LEDs Front Panel The Multiple RF Home Gateway has 9 LEDs. POWER (Green) WiFi (Green) Z-Wave (Green) ZigBee (Green) Bluetooth LE On - Power On/Normal Operation Off - Power Off Flashing - Rebooting. On - WPS mode is selected. On (5 seconds) - WiFi connection is established. Off - No WiFi connection available. Flashing - Data is being transmitted or received via the Wireless connection. On - Z-Wave mode is selected.
(Green) 3G (Green) 433MHz/345MHz (Green) Service (Green) Voice (Green) Voice Button On (5 seconds) - Bluetooth sensor added or synchronization is successful. Off - Bluetooth module is in idle mode. Flashing - Bluetooth module is in active mode. On - 3G connection established. Off - No active 3G connection. Flashing - Data is being transmitted or received via the 3G connection. On - 433MHz/345MHz mode is selected.
Sync Button Reset After selecting the RF mode, push the Sync button to synchronize the gateway and sensors. Push the Sync button for three seconds again to stop the synchronization process if needed. This button has two (2) functions: Reboot. When pressed and released, the Multiple RF Home Gateway will reboot (restart). Clear All Data. This button can also be used to clear ALL data and restore ALL settings to the factory default values.
Chapter 2 Initial Installation 2 This Chapter covers the software installation of the Multiple RF Home Gateway. Requirements Use a standard 10/100/1000 BaseT network (UTP) cable with RJ45 connector. Procedure 1. Choose an Installation Site Select a suitable place to install the Multiple RF Home Gateway. 2. Connect Battery Plug Connector The supplied backup battery can provide excellent continuous power source when disconnecting power to the device. 1.
3. Attach the back cover to the device with the screws. 3. Connect LAN Cable Use a standard LAN cable to connect the device to the Ethernet port on the Multiple RF Home Gateway. 4. Power Up Connect the supplied power adapter to the Multiple RF Home Gateway. Use only the power adapter provided. Using a different one may cause hardware damage. 5. Check the LEDs The Power LED should be ON. The WiFi LED should be ON (provided the PC is also ON.
Initial Installation SIM Card Installation 1. 2. 3. Ensured the device is powered off. Remove the screws on the back cover of the device with a screwdriver. Find the location of the SIM card tray. 4. Push the SIM card cover upward. 5. 6. 7. Insert the SIM card into the slot. Make sure the SIM card is installed correctly. Put the SIM card cover back. Attach the back cover to the device with the screws.
Chapter 3 Configuration 3 This Chapter provides Setup details of the Gateway. Configuration The Multiple RF Home Gateway can offer customers with seamless communication between devices and clouds while at home or away. This gateway is designed to provide complete connectivity with all certified devices including cameras, security systems and WiFi/ZigBee/ZWave/Bluetooth/3G devices.
Appendix A Specifications A Multiple RF Home Gateway Model Multiple RF Home Gateway Dimensions 222mm(W) * 148mm(D) * 48mm(H) Operating Temperature 0 C to 40 C Buttons 4 Network Protocol: TCP/IP Network Interface: 1 * 10/100/1000BaseT (RJ45) LAN connection LEDs 9 Battery 2S1P 18650 Battery USB Port 1 * USB 2.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules.
