1n Dual Band Wireless Access Point User's Guide
TABLE OF CONTENTS CHAPTER 1 INTRODUCTION ............................................................................................. 1 Features of your Wireless Access Point ........................................................................... 1 Package Contents .............................................................................................................. 3 Physical Details ...............................................................................................................
Status Screen .................................................................................................................... 99 APPENDIX A SPECIFICATIONS ..................................................................................... 101 Wireless Access Point .................................................................................................... 101 APPENDIX B TROUBLESHOOTING .............................................................................. 104 Overview ................
Chapter 1 Introduction 1 This Chapter provides an overview of the Wireless Access Point's features and capabilities. Congratulations on the purchase of your new Wireless Access Point. The Wireless Access Point links your Wireless Stations to your wired LAN. With the Wireless Access Point, you can select either 2.4 GHz or 5 GHz radio bands, which provides the flexibility to manage a graceful transition from networks.
Wireless Access Point User Guide Upgradeable Firmware. Firmware is stored in a flash memory and can be upgraded easily, using only your Web Browser. PoE Support. You can use PoE (Power over Ethernet) to provide power to the Wireless Access Point, so only a single cable connection is required. Security Features Virtual APs. For maximum flexibility, wireless security settings are stored in Virtual AP. Up to 16 Virtual APs can be defined and used as any time. Multiple BSSIDs.
Introduction SNMP Support. SNMP (Simple Network Management Protocol) is supported, allowing you to use a SNMP program to manage the Wireless Access Point. When stores the configuration, will not affect the operation of SNMP and CLI. VPN Pass – through. Do not affect related application operation (such as ICMP, FTP, HTTP, Etc.) when in IP network, and support VPN Pass - through function.
Wireless Access Point User Guide Physical Details Front Panel LEDs Figure 2: Front Panel Antenna Ports (Left Side) Attach the 5G antennas here. Status On - Error condition. Off - Normal operation. Blinking - During start up, and when the Firmware is being upgraded. Power On - Normal operation. Off - No power Ethernet On - Corresponding LAN (hub) port is active. Off - No active connection on the corresponding LAN (hub) port.
Introduction Rear Panel Figure 3: Rear Panel Reset Button This button has two (2) functions: Reboot. When pressed and released, the Wireless Access Point will reboot (restart). Reset to Factory Defaults. This button can also be used to clear ALL data and restore ALL settings to the factory default values. To Clear All Data and restore the factory default values: 1. Hold the Reset Button until the Status (Red) LED blinks TWICE, usually more than 5 seconds. 2. Release the Reset Button.
Wireless Access Point User Guide Wall Mount Template The following image illustrates the mounting slots on the bottom of the device.
Chapter 2 Installation 2 This Chapter covers the physical installation of the Wireless Access Point. Requirements Requirements: TCP/IP network Ethernet cable with RJ-45 connectors Installed Wireless network adapter for each PC that will be wirelessly connected to the network. Procedure 1. Select a suitable location for the installation of your Wireless Access Point.
Wireless Access Point User Guide 2. 3. 4. Use a standard LAN cable to connect the "LAN" port on the Wireless Access Point to a 10/100/1000BaseT hub/switch on your LAN. Connect the supplied power adapter to the Wireless Access Point and a convenient power outlet, and power up. Check the LEDs: The Status LED should flash, then turn OFF. The Power and Ethernet LEDs should be ON. For more information, refer to Front Panel LEDs in Chapter 1.
Chapter 3 Access Point Setup 3 This Chapter provides details of the Setup process for Basic Operation of your Wireless Access Point. Overview This chapter describes the setup procedure to make the Wireless Access Point a valid device on your LAN, and to function as an Access Point for your Wireless Stations. Wireless Stations may also require configuration. For details, see Chapter 4 - PC and Server Configuration. The Wireless Access Point can be configured using your Web Browser.
Wireless Access Point User Guide current user name and password, as set on the Administration-Management-Account screen. Figure 7: Password Dialog 6. 7. 8. You will then see the Status screen, which displays the current settings and status. No data input is possible on this screen. See Chapter 5 for details of the Status screen. From the menu, check the following screens, and configure as necessary for your environment.
Access Point Setup System - Basic Settings Screen Click Basic Settings on the System menu to view a screen like the following. Figure 8: Basic Settings Screen Data - Basic Settings Screen Basic Settings Access Point Name It displays the default host name of the device. Enter a suitable name for this Access Point if required. Description If desired, you can enter a description for the Access Point. Country/Domain The country or domain which is matching your current location.
Wireless Access Point User Guide System - Time Settings Screen Figure 9: Time Settings Screen Data - Time Settings Screen TimeZone Time Settings Select either Manually or Automatically Manually Date - Select the date to match your location. Time - Enter the correct time. Automatically Current Time - It displays the current date and time. Time Zone - Choose the Time Zone for your location from the drop-down list.
Access Point Setup System - SNMP Settings SNMP (Simple Network Management Protocol) is only useful if you have a SNMP program on your PC. To reach this screen, select SNMP in the System section of the menu. Basic Screen Figure 10: Basic Screen Data - Basic Screen Basic SNMP v1/v2/v3 Use this to enable or disable SNMP as required. Contact The identification of the contact person. Device Name Enter the desired name for the device. Location The physical location of this node.
Wireless Access Point User Guide SNMPv3 Figure 11: SNMPv3 Screen Data - SNMPv3 Screen SNMPv3 User Name Enter the user name for SNMPv3. Authentication Protocol Select the authentication protocol used by SNMPv3. Authentication Key Enter the authentication key required by SNMPv3. Privacy Protocol Select the private protocol as required. Privacy Key Enter the private key here.
Access Point Setup SNMP Trap Figure 12: SNMP Trap Screen Data - SNMP Trap Screen SNMP Trap Server 1 Enter the IP address of the server 1. Server 2 Enter the IP address of the server 2 in case the server 1 is not available. Server Port Enter the port number for the server. Trap Periods Enter the desired hours (1 ~ 65535). Trap Threshold Rate of CPU Utilization When Rate of CPU Utilization reaches the threshold, then one SNMP trap will be sent out.
Wireless Access Point User Guide System - Log Settings If you have a Syslog Server on your LAN, this screen allows you to configure the Access Point to send log data to your Syslog Server. Figure 13: Syslog Settings Screen Data - Syslog Settings Screen Syslog Mode Select the desired Option: Disabled - Syslog server is not used. Broadcast - Syslog data is broadcast. Use this option if different PCs act as the Syslog server at different times.
Access Point Setup Mail Alerts Figure 14: Mail Alerts Screen Data - Mail Alerts Screen Email Alerts Email Alerts If enabled, an E-mail will be sent. If enabled, the e-mail address information (below) must be provided. Log Queue Length Enter the desired length of the log queue. The default is 20 entries. Log Time Threshold Enter the preferred value between 60 and 600, which determine how often the log will be emailed to you. Normally, this can be left at the default value. The default is 600 seconds.
Wireless Access Point User Guide Log Types Figure 15: Log Types Screen Data - Log Types Screen Log Types Log Types Use these checkboxes to determine which events are included in the log. Checking all options will increase the size of the log, so it is good practice to disable any events which are not really required. Unauthorized Login Attempt - If checked, the unauthorized users who attempted to login to the Access Point are logged.
Access Point Setup Wireless - Basic Settings Screen The settings on this screen must match the settings used by Wireless Stations. WLAN Figure 16: WLAN Settings Screen Data - WLAN Settings Screen Operation Wireless Radio Select the either Radio 1 or Radio 2 for the wireless feature. Radio Function Enable this to use the wireless feature.
Wireless Access Point User Guide Wireless Mode For 5G, select the desired option: 802.11a Only (5G) - only 802.11a connections are allowed. If you only have 802.11a, selecting this option may provide a performance improvement over using the default setting. 802.11n Only (5G) - only 802.11n connections are allowed. If you only have 802.11n, selecting this option may provide a performance improvement over using the default setting. 802.11a and 802.
Access Point Setup cause interference with other devices. Channel Bandwidth Select the desired bandwidth from the list. Extension Sub-Channel Select Above or Below Primary Channel from the list. Operation Mode Figure 17: Operation Mode Data - Operation Mode Settings Screen Operation Wireless Radio Select the either Radio 1 or Radio 2 for the wireless feature. Operation Mode Select the desired option from the list: AP: Choose this to make the device act as a normal AP.
Wireless Access Point User Guide Figure 18: Virtual APs Settings Data - Virtual APs Settings Screen VAPs Wireless Radio Select the either Radio 1 or Radio 2 for the wireless feature. VAP List All available VAPs are listed. Up to 16 VAPs/Radios can be supported. For each VAP, the following data is displayed: * If displayed before the name of the VAP, this indicates the VAP is currently enabled. If not displayed, the VAP is currently disabled. VAP Name The current VAP name is displayed.
Access Point Setup Separation" setting on the "Advanced" screen has been enabled.
Wireless Access Point User Guide Virtual AP Screen This screen is displayed when you select a VAP on the Virtual AP Settings screen, and click the Configure button. Figure 19: Virtual VAP Screen Data - Virtual VAP Screen Basic Settings VAP Name Enter a suitable name for this VAP. SSID Enter the desired SSID. Each VAP must have a unique SSID. Broadcast SSID If Disabled, no SSID is broadcast. If enabled, the SSID will then be broadcast to all Wireless Stations.
Access Point Setup Max Upstream Rate Enter the maximum upstream rate for the VAP. "0" means no limit. Station Rate Limit Max Downstream Rate Enter the maximum downstream rate for each wireless station. "0" means no limit. Max Upstream Rate Enter the maximum upstream rate for each wireless station. "0" means no limit. Security Security System Choose the security method from the drop-down list. Refer to the following section for more details.
Wireless Access Point User Guide All data transmission is encrypted using the WPA2 standard. Keys are automatically generated, so no key input is required. WPA and WPA2 with Radius - EITHER WPA or WPA2 require a Radius Server on your LAN to provide the client authentication according to the 802.1x standard. Data transmissions are encrypted using EITHER WPA or WPA2 standard. If this option is selected: This Access Point must have a "client login" on the Radius Server.
Access Point Setup Security Settings - None Figure 20: Wireless Security - None No security is used. Anyone using the correct SSID can connect to your network.
Wireless Access Point User Guide Security Settings - WEP This is the 802.11b standard. Data is encrypted before transmission, but the encryption system is not very strong. Figure 21: WEP Screen Data - WEP Screen WEP Data Encryption Select the desired option, and ensure your Wireless stations have the same setting: 64 Bit Encryption - Keys are 10 Hex (5 ASCII) characters. 128 Bit Encryption - Keys are 26 Hex (13 ASCII) characters. 152 Bit Encryption - Keys are 32 Hex (16 ASCII) characters.
Access Point Setup Authentication Normally, you can leave this at “Automatic”, so that Wireless Stations can use either method ("Open System" or "Shared Key".). If you wish to use a particular method, select the appropriate value "Open System" or "Shared Key". All Wireless stations must then be set to use the same method. Key Input Select "Hex" or "ASCII" depending on your input method. (All keys are converted to Hex, ASCII input is only for convenience.
Wireless Access Point User Guide Security Settings - WPA-PSK Like WEP, data is encrypted before transmission. WPA is more secure than WEP, and should be used if possible. The PSK (Pre-shared Key) must be entered on each Wireless station. The 256Bit encryption key is derived from the PSK, and changes frequently. Figure 22: WPA-PSK Screen Data - WPA-PSK Screen WPA-PSK Network Key Enter the key value. Data is encrypted using a 256Bit key derived from this key. Other Wireless Stations must use the same key.
Access Point Setup Security Settings - WPA2-PSK This is a further development of WPA-PSK, and offers even greater security, using the AES (Advanced Encryption Standard) method of encryption. Figure 23: WPA2-PSK Screen Data - WPA2-PSK Screen WPA2-PSK Network Key Enter the key value. Data is encrypted using a 256Bit key derived from this key. Other Wireless Stations must use the same key. Encryption The encryption method is AES. Wireless Stations must also use AES.
Wireless Access Point User Guide Security Settings - WPA-PSK and WPA2-PSK This method, sometimes called "Mixed Mode", allows clients to use EITHER WPA-PSK (with TKIP) OR WPA2-PSK (with AES). Figure 24: WPA-PSK and WPA2-PSK Screen Data - WPA-PSK and WPA2-PSK Screen WPA-PSK and WPA2-PSK Network Key Enter the key value. Data is encrypted using this key. Other Wireless Stations must use the same key. Encryption Select the desired encryption method from the list.
Access Point Setup Security Settings - WPA with Radius This version of WPA requires a Radius Server on your LAN to provide the client authentication according to the 802.1x standard. Data transmissions are encrypted using the WPA standard. Figure 25: WPA with Radius Screen Data - WPA with Radius Screen WPA with Radius WPA Encryption The encryption method is TKIP. Wireless Stations must also use TKIP.
Wireless Access Point User Guide Security Settings - WPA2 with Radius This version of WPA2 requires a Radius Server on your LAN to provide the client authentication according to the 802.1x standard. Data transmissions are encrypted using the WPA2 standard. Figure 26: WPA2 with Radius Screen Data - WPA2 with Radius Screen WPA2 with Radius WPA Encryption The encryption method is AES. Wireless Stations must also use AES.
Access Point Setup Security Settings - WPA and WPA2 with Radius EITHER WPA or WPA2 require a Radius Server on your LAN to provide the client authentication according to the 802.1x standard. Data transmissions are encrypted using EITHER WPA or WPA2 standard. Figure 27: WPA and WPA2 with Radius Screen Data - WPA and WPA2 with Radius Screen WPA and WPA2 with Radius WPA Encryption Select the desired encryption method from the list.
Wireless Access Point User Guide Security Settings - 802.1x This uses the 802.1x standard for client authentication, and WEP for data encryption. If this option is selected: This Access Point must have a "client login" on the Radius Server. Each user must have a "user login" on the Radius Server. Normally, a Certificate is used to authenticate each user. See Chapter4 for details of user configuration. Each user's wireless client must support 802.1x.
Access Point Setup Wireless - Radius Settings Clicking the Radius link on the Wireless menu will result in a screen like the following. Figure 29: Authentication Server Settings Data - Authentication Server Screen Authentication Server Primary IP Address Enter the name or IP address of the Radius Server on your network. Port Number Enter the port number used for connections to the Radius Server. Shared Secret Enter the key value to match the Radius Server.
Wireless Access Point User Guide Accounting Server Figure 30: Accounting Server Screen Data - Accounting Server Screen Accounting Server Primary IP Address Enter the IP address in the following fields if you want this Access Point to send accounting data to the Radius Server. Port Number The port used by your Radius Server must be entered in the field. Shared Secret Enter the key value to match the Radius Server.
Access Point Setup Wireless - Access Control This feature can be used to block access to your LAN by unknown or untrusted wireless stations. Click Access Control on the Wireless menu to view a screen like the following. Figure 31: Access Control Screen Data - Access Control Screen Wireless Radio Select the either Radio 1 or Radio 2 for the wireless feature. Enable Access Control Enable or Disable the Access Control feature as required.
Wireless Access Point User Guide Control Type There are three options: Open Allow Following MAC Addresses to Connect to Wireless network - It's only used for Access Control with Local Database. If selected, then clients with MAC Addresses in Local Database can connect to the wireless network. Deny Following MAC Addresses to Connect to Wireless network - It's only used for Access Control with Local Database.
Access Point Setup Wireless - QoS Settings QoS Screen Clicking the QoS link on the Wireless menu will result in a screen like the following. Figure 32: QoS Screen Data - QoS Screen Parameters Enable Upstream QoS Enable or Disable upstream QoS of Ethernet Port. The QoS includes four outbound priority queues. The packets from high priority queue will be processed first. Upstream Bandwidth Specify the maximum upstream bandwidth of the AP.
Wireless Access Point User Guide Wireless - Advanced Settings Parameters Screen Clicking the Parameters link on the Wireless menu will result in a screen like the following. Figure 33: Parameters Screen Data - Parameters Screen Parameters Wireless Radio Select the either Radio 1 or Radio 2 for the wireless feature. Fragmentation Length Enter the preferred setting between 256 and 2346. Normally, this can be left at the default value. Beacon Interval Enter the preferred setting between 20 and 1000.
Access Point Setup 802.11b Protection Mode The Protection system is intended to prevent older 802.11b devices from interfering with 802.11g transmissions. (Older 802.11b devices may not be able to detect that the 802.11g transmission is in progress.) Station Idle Time This indicates the time (seconds) of the station whose node will be deleted from AP if there is no traffic for the link. TX/RX Chainmask Select the desired TX/RX chainmask.
Wireless Access Point User Guide User Control Screen Click User Control on the Wireless menu to view a screen like the following: Figure 34: User Control Screen Data - User Control Screen User Control Wireless Radio Select the either Radio 1 or Radio 2 for the wireless feature. User Control Mode Select the method of controlling the Wireless Stations. It can be one of following options: Disable - This function is disabled.
Access Point Setup Auto Frequency Screen Figure 35: Auto Frequency Screen Data - Auto Frequency Screen Auto Frequency Wireless Radio Select the either Radio 1 or Radio 2 for the wireless feature. Auto Frequency Mode If enabled, the device can adjust its wireless channel at a specified interval. Auto Frequency Adjust Interval Specify the interval at which the device will scan and adjust its wireless channel.
Wireless Access Point User Guide Load Balance Screen Figure 36: Load Balance Screen Data - Load Balance Screen Load Balance Load Balance Mode Enable or disable this function. Load Balance Group Specify the group name. The feature will only work with the Access Points that are in same group. User Number Interval Specify the User Number Interval. When user number difference of Access Points reaches the interval, the new client will connect to the Access Point with fewer users.
Access Point Setup WMM Screen Figure 37: WMM Screen Data - WMM Screen WMM Wireless Radio Select the desired radio option from the list. WMM Support Check this to enable WMM (Wi-Fi Multimedia) support. This feature is also supported by your wireless clients, whose voice and multimedia traffic will be given a higher priority than other traffic.
Wireless Access Point User Guide TXOPlimit Transmission opportunity limit (TXOPLimit) indicates the maximum time, which a user can use a channel after a successful contention. The greater the TXOPLimit is, the longer the user can use the channel. The value 0 indicates that the user can send only one packet each time when it uses the channel. Band Select Screen Figure 38: Band Select Screen Data - Band Select Screen Band Select Band Select Function When 2.
Access Point Setup Rate Limitation Screen Figure 39: Rate limitation Screen Data - Rate limitation Screen Rate limitation Rate Limitation If this feature is enabled, it will be disconnected when one wireless client's link rate is lower than the specified lowest rate in a specified duration. Lowest Rate Select the lowest rate from the list. Rate Duration Choose the desired duration from the drop-down list.
Wireless Access Point User Guide Interference Detection Screen Figure 40: Interference Detection Screen Data - Interference Detection Screen Interference Detection Co-channel Interference Check it to enable the detecting interference of APs with same channels. Adjacent-channel Interference Check it to enable the detecting interference of APs with adjacent channels. Detecting Interval Specify the interval for detecting. Log by Syslog Enable it if you want to use this function.
Access Point Setup Network - Device Mode Screen Figure 41: Device Mode Screen Data - Device Mode Screen Device Mode If bridge mode is selected, then the device will act as an Access Point. If router mode is selected, then the device will act as a router.
Wireless Access Point User Guide Network - IP Settings Screen Figure 42: IP Settings Screen Data - IP Settings Screen IP Settings IP Settings Select the desired option from the drop-down list. Static - Select it if you want to configure one static IP Address for the Access Point. You need input following settings: IP Address: The IP Address of this device. Subnet Mask: The Network Mask associated with the IP |Address above. Default Gateway: The IP Address of your Gateway or Router.
Access Point Setup AC IP Address Enter the IP address for the AC. It's necessary when the IP Settings is "Static". AC DNS Name 1 Enter the primary DNS name for the AC. AC DNS Name 2 Enter the secondary DNS name for the AC. It is optional.
Wireless Access Point User Guide Network - VLAN Settings Screen Figure 43: VLAN Settings Screen Data - VLAN Settings Screen VLAN Settings Enable 802.1Q VLAN This option is only useful if the hubs/switches on your LAN support the VLAN standard. Native VLAN Enter the value for Native VLAN.
Access Point Setup Management VLAN Define the VLAN ID used for management. Wireless Radio Select the desired option from the list. VLAN Table 802.1p setting: Enter the values for VLAN ID, Default Priority, WMM VO Priority, WMM VI Priority, WMM BE Priority, WMM BK Priority in the table.
Wireless Access Point User Guide Network - IGMP Settings Screen Figure 44: IGMP Settings Screen Data - IGMP Settings Screen IGMP Settings IGMP Snooping This option is only useful if the hubs/switches on your LAN support the VLAN standard.
Access Point Setup Network - STP Screen Figure 45: STP Screen Data - STP Screen STP Enable Spanning Tree Protocol Enable this if you want to use this feature.
Wireless Access Point User Guide Network - Bridge Parameters Screen Figure 46: Bridge Parameters Screen Data - Bridge Parameters Screen Bridge Parameters Ageing Time This value indicates the ageing time on the bridge. If it is timeout, this station will be removed from the bridge table.
Chapter 4 PC and Server Configuration 4 This Chapter details the PC Configuration required for each PC on the local LAN. Overview All Wireless Stations need to have settings which match the Wireless Access Point. These settings depend on the mode in which the Access Point is being used. If using WEP or WPA-PSK, it is only necessary to ensure that each Wireless station's settings match those of the Wireless Access Point, as described below. For 802.1x modes, configuration is much more complex.
Wireless Access Point User Guide Using WPA-PSK/WPA2-PSK For each of the following items, each Wireless Station must have the same settings as the Wireless Access Point. Mode On each PC, the mode must be set to Infrastructure. SSID (ESSID) This must match the value used on the Wireless Access Point. The default value is wireless Note! The SSID is case sensitive. Wireless Security On each client, Wireless security must be set to WPA-PSK.
PC and Server Configuration Using WPA-Enterprise This is the most secure and most complex system. WPA-Enterprise mode provides greater security and centralized management, but it is more complex to configure. Wireless Station Configuration For each of the following items, each Wireless Station must have the same settings as the Wireless Access Point. Mode On each PC, the mode must be set to Infrastructure. SSID (ESSID) This must match the value used on the Wireless Access Point.
Wireless Access Point User Guide 802.1x Server Setup (Windows 2000 Server) This section describes using Microsoft Internet Authentication Server as the Radius Server, since it is the most common Radius Server available that supports the EAP-TLS authentication method.
PC and Server Configuration Figure 47: Components Screen 4. 5. Click Next. Select the Enterprise root CA, and click Next. Figure 48: Certification Screen 6. Enter the information for the Certificate Authority, and click Next.
Wireless Access Point User Guide Figure 49: CA Screen 7. 8. Click Next if you don't want to change the CA's configuration data. Installation will warn you that Internet Information Services are running, and must be stopped before continuing. Click Ok, then Finish. DHCP server configuration 1. 2. Click on the Start - Programs - Administrative Tools - DHCP Right-click on the server entry as shown, and select New Scope. Figure 50: DHCP Screen 3. 4. 5. Click Next when the New Scope Wizard Begins.
PC and Server Configuration Figure 51: IP Address Screen 6. Add exclusions in the address fields if required. If no exclusions are required, leave it blank. Click Next. 7. Change the Lease Duration time if preferred. Click Next. 8. Select Yes, I want to configure these options now, and click Next. 9. Enter the router address for the current subnet. The router address may be left blank if there is no router. Click Next. 10.
Wireless Access Point User Guide Certificate Authority Setup 1. 2. Select Start - Programs - Administrative Tools - Certification Authority. Right-click Policy Settings, and select New - Certificate to Issue. Figure 53: Certificate Authority Screen 3. Select Authenticated Session and Smartcard Logon (select more than one by holding down the Ctrl key). Click OK. Figure 54: Template Screen 4. 5. Select Start - Programs - Administrative Tools - Active Directory Users and Computers.
PC and Server Configuration Figure 55: Active Directory Screen 6. Select the Group Policy tab, choose Default Domain Policy then click Edit. Figure 56: Group Policy Tab 7. Select Computer Configuration - Windows Settings - Security Settings - Public Key Policies, right-click Automatic Certificate Request Settings - New - Automatic Certificate Request.
Wireless Access Point User Guide Figure 57: Group Policy Screen 8. 9. When the Certificate Request Wizard appears, click Next. Select Computer, then click Next. Figure 58: Certificate Template Screen 10. Ensure that your certificate authority is checked, then click Next. 11. Review the policy change information and click Finish. 12. Click Start - Run, type cmd and press enter. Enter secedit /refreshpolicy machine_policy This command may take a few minutes to take effect.
PC and Server Configuration Internet Authentication Service (Radius) Setup 1. 2. Select Start - Programs - Administrative Tools - Internet Authentication Service Right-click on Clients, and select New Client. Figure 59: Service Screen 3. 4. 5. 6. 7. 8. Enter a name for the access point, click Next. Enter the address or name of the Wireless Access Point, and set the shared secret, as entered on the Security Settings of the Wireless Access Point. Click Finish.
Wireless Access Point User Guide 11. Click Edit Profile... and select the Authentication tab. Enable Extensible Authentication Protocol, and select Smart Card or other Certificate. Deselect other authentication methods listed. Click OK. Figure 61: Authentication Screen 12. Select No if you don't want to view the help for EAP. Click Finish.
PC and Server Configuration Remote Access Login for Users 1. 2. 3. Select Start - Programs - Administrative Tools- Active Directory Users and Computers. Double click on the user who you want to enable. Select the Dial-in tab, and enable Allow access. Click OK.
Wireless Access Point User Guide Using 802.1x Mode (without WPA) This is very similar to using WPA-Enterprise. The only difference is that on your client, you must NOT enable the setting The key is provided for me automatically. Instead, you must enter the WEP key manually, ensuring it matches the WEP key used on the Access Point. Figure 63: Properties Screen Note: On some systems, the "64 bit" WEP key is shown as "40 bit" and the "128 bit" WEP key is shown as "104 bit".
Chapter 5 Operation and Status 5 This Chapter details the operation of the Wireless Access Point and the status screens. Status Screen Use the Status link on the main menu to view this screen. Figure 64: Device Info Screen Data - Device Info Screen Access Point Hardware Version The version of the hardware currently used. Firmware Version The version of the firmware currently installed. Bootloader Version The version of the bootloader currently used.
Wireless Access Point User Guide System Status This screen is displayed when the System Status button is clicked. Figure 65: System Status Screen Data - System Status Screen Access Point Name The current name will be displayed. MAC Address The MAC (physical) address of the Wireless Access Point. Country/Domain The region or domain, as selected on the System screen. System Up Time This indicates how long the system has been running since the last restart or reboot.
Operation and Status Network Status This screen is displayed when the Network Status button is clicked. Figure 66: IP Settings Screen Data - IP Settings Screen TCP/IP IP Type The current IP type is displayed. IP Address The IP Address of the Wireless Access Point. Subnet Mask The Network Mask (Subnet Mask) for the IP Address above. Gateway Enter the Gateway for the LAN segment to which the Wireless Access Point is attached (the same value as the PCs on that LAN segment).
Wireless Access Point User Guide Ethernet This screen is displayed when the Ethernet button is clicked. Figure 67 Ethernet Screen Data - Ethernet Screen Ethernet Ethernet Status The current Ethernet status is displayed.
Operation and Status VLAN This screen is displayed when the VLAN button is clicked. Figure 68: VLAN Screen Data - VLAN Screen VLAN VLAN The current VLAN status is displayed. Management VLAN ID It displays the VLAN ID of Management VLAN.
Wireless Access Point User Guide Wireless Status Basic Screen Figure 69: Basic Screen Data - Basic Screen Basic AP Mode The current Access Point mode is displayed. Channel/Frequency The Channel currently in use is displayed. Wireless Mode The current mode (e.g. 802.11g) is displayed. WMM Support "Enabled" or "Disabled" is displayed for the WMM status. WMM Power Save Support "Enabled" or "Disabled" is displayed for the WMM Power Save status.
Operation and Status Virtual AP Status Screen Figure 70: Virtual AP Status Screen Data - Virtual AP Status Screen Virtual AP Status Wireless Radio Select the desired band (2.4 GHz or 5 GHz) used by this profile. Name The name you gave to this profile; if you didn't change the name, the default name is used. BSSID The BSSID assigned to this profile. SSID The SSID assigned to this profile. SSID Broadcast Indicates whether or not the SSID is broadcast.
Wireless Access Point User Guide Wireless Stations Screen Figure 71: Wireless Stations Screen Data - Wireless Station Screen Station List Wireless Radio Select the desired band (2.4 GHz or 5 GHz) used by this profile. Station ID The ID of each Wireless Station is displayed. If the ID is not known, "unknown" will be displayed. MAC Address The MAC (physical) address of each Wireless Station is displayed. SSID This displays the SSID used by the Wireless station.
Operation and Status WDS Status Screen Figure 72: WDS Status Screen Data - WDS Status Screen Wireless Radio Select the desired band (2.4 GHz or 5 GHz) used by this profile. Root AP Status The following table shows the current status of the root AP. WDS Client Status The following table shows the current status of the WDS Client.
Wireless Access Point User Guide Log Screen Figure 73: Log Screen Data - Log Screen Data Current Time The system date and time is displayed. Log The Log shows details of the connections to the Wireless Access Point. Buttons Refresh Update the data on screen. Save File Save the log to a file on your pc. Clear Log This will delete all data currently in the Log. This will make it easier to read new messages.
Operation and Status Statistics Screen Ethernet Screen Figure 74: Ethernet Screen Data - Ethernet Screen Ethernet Packets Received The number of packets received by the Access Point. Packets Sent The number of packets sent by the Access Point. Bytes Received The number of bytes received by the Access Point. Bytes Sent The number of bytes sent by the Access Point. Error Packets Received The number of error packets received. Drop Received Packets The number of drop packets received.
Wireless Access Point User Guide Wireless Screen Figure 75: Wireless Screen Data - Wireless Screen VAP1~VAP16 Wireless Radio Select the desired band (2.4 GHz or 5 GHz) used by this profile.
Operation and Status Packets Received The number of packets received by the Access Point. Packets Sent The number of packets sent by the Access Point. Bytes Received The number of bytes received by the Access Point. Bytes Sent The number of bytes sent by the Access Point. Error Packets Received The number of error packets received. Drop Received Packets The number of drop packets.
Chapter 6 Access Point Management 6 This Chapter explains when and how to use the Wireless Access Point's "Administration" Features. Overview This Chapter covers the following features, available on the Wireless Access Point’s Administration menu. AP Type Management Auto Config Config File Ping Test Auto Reboot Firmware Upgrade AP Type Figure 76: AP Type Screen Data - AP Type Screen Account AP Type Select the AP type as required.
Access Point Management Management Screen Account Screen The Account screen allows you to assign or modify the names and passwords for the administrator and maintainer. It is recommended that this be changed, using this screen. Figure 77: Account Screen Data - Account Screen Account Admin User Name Enter the login name for the Administrator. The administrator has the maintenance and operation for all the functions.
Wireless Access Point User Guide Re-enter to Confirm Re-enter the desired login password. Method Screen Figure 78: Method Screen Data - Method Screen Method Enable Wireless Web Access Enable this to allow wireless client access the device. Enable HTTP Enable this to allow admin connections via HTTP. If enabled, you must provide a port number in the field below. Either HTTP or HTTPS must be enabled. HTTP Port Number Enter the port number to be used for HTTP connections to this device.
Access Point Management Control Screen This feature can be used to block access to your LAN by unknown or untrusted wireless stations. Figure 79: Control Screen Data - Control Screen Turn IP Management Control On Select the desired option, as required Enable or Disable the Management Control feature. Select either Allow following IP addresses to Manage the Device or Deny following IP addresses to Manage the Device. Enter the physical IP address and Subnet Mask of each Wireless station.
Wireless Access Point User Guide Auto Config To reach this screen, select Auto Config in the Administration section of the menu. Figure 80: Auto Config Screen Data - Auto Config Screen Auto Config Auto Config If enabled, this AP will perform Auto Configuration. FTP Server Enter the address for the FTP server. User Name Enter the login name for the FTP server. Password Enter the login password for the FTP server. Config File Enter the full path of the firmware in the FTP server.
Access Point Management Config File This screen allows you to Backup (download) the configuration file, and to restore (upload) a previously-saved configuration file. You can also set the Wireless Access Point back to its factory default settings. To reach this screen, select Config File in the Management section of the menu.
Wireless Access Point User Guide Defaults Revert to factory default settings To erase the current settings and restore the original factory default settings, click Restore to Defaults button. Note! This will terminate the current connection. The Access Point will be unavailable until it has restarted. By default, the Access Point will act as a DHCP client, and automatically obtain an IP address. You will need to determine its new IP address in order to re-connect.
Access Point Management Ping Test This screen allows you to perform a "Ping". These activities can be useful in solving network problems. Figure 82: Ping Test Screen Data - Ping Test Screen Ping Ping Test Mode Select the desired option from the drop-down list. Ping IP Address Enter the IP address you wish to ping. The IP address can be on your LAN, or on the Internet. Note that if the address is on the Internet, and no connection currently exists, you could get a "Timeout" error.
Wireless Access Point User Guide Auto Reboot If you have a Syslog Server on your LAN, this screen allows you to configure the Access Point to send log data to your Syslog Server. Figure 83: Auto Reboot Screen Data - Auto Reboot Screen Auto Reboot Mode Reboot Interval Select the desired Option: Disable - Auto Reboot feature is not used. Enable - Auto Reboot feature is in use. Enter the desired time for reboot interval.
Access Point Management Firmware Upgrade The firmware (software) in the Wireless Access Point can be upgraded using your Web Browser. You must first download the upgrade file, and then select Upgrade Firmware in the Management section of the menu. You will see a screen like the following. Figure 84: Firmware Upgrade Screen To perform the Firmware Upgrade: 1. 2. 3. Click the Browse button and navigate to the location of the upgrade file. Select the upgrade file.
Chapter 7 Access Point Mode 7 This Chapter explains configuration and operation when in "Access Point". Overview There are two modes available on the Device Mode screen. Router - In this mode, this device can provide shared Internet Access to all your LAN users. Also, by default, it acts a DHCP Server, providing an IP address and related information to all Wireless and LAN users. Bridge - The device links your Wireless Stations to your wired LAN.
Access Point Mode Home Screen If in Access Point mode, the home screen will look like the example below. Figure 85: Home Screen - Bridge Mode Note that the menu has changed, many of the options in Router mode are the same as Bridge mode. The screens available are: Device Mode - change back to Router mode, if desired. System - this screen and related sub-screens are the same as in Router mode. Wireless - this screen and related sub-screens are the same as in Router mode.
Wireless Access Point User Guide Device Mode Screen This screen is used to change back to Router mode, if desired. Figure 86: Device Mode Screen Data - Device Mode Screen Device Mode Select the desired device mode for the router: Router - In this mode, this device can provide shared Internet Access to all your LAN users. Also, by default, it acts a DHCP Server, providing an IP address and related information to all Wireless and LAN users.
Access Point Mode Status Screen In Access Point mode, the Status screen looks like the example below. Figure 87: Device Info Screen - Bridge Mode Data - Device Info Screen (Bridge Mode) Device Info Hardware Version The version of the hardware currently used. Firmware Version The version of the firmware currently installed. Bootloader Version The version of the bootloader currently used. Serial Number The serial number of the device. AP Type The current AP type is displayed.
Wireless Access Point User Guide VLAN Screen In Access Point mode, the VLAN screen looks like the example below. Figure 88: VLAN Screen Data - VLAN Screen VLAN VLAN(802.1Q) It displays the status (Enabled or disabled) of VLAN. Management VLAN ID It displays the VLAN ID of Management VLAN.
Appendix A Specifications A Wireless Access Point Hardware Specifications LAN port 1 x RJ45 auto-sensing 10/100/1000BASE-TX Ethernet with 802.3af+ PoE. Can support Full Duplex and Half Duplex transfer function. Antennae 4 external omni antennas Operating Temperature -10 C to 50 C Operating Humidity 10% - 90% non-condensing Power Adapter 12V/1A External Console Port 1 x RJ45-base Console Wireless Interface Standards IEEE 802.11a/b/g/n 2.
Wireless Access Point User Guide Connectivity Up to 128 clients per band (256 total) 102
Appendix A - Specifications FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Wireless Access Point User Guide FCC RF Radiation Exposure Statement 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Appendix B Troubleshooting B Overview This chapter covers some common problems that may be encountered while using the Wireless Access Point and some possible solutions to them. If you follow the suggested steps and the Wireless Access Point still does not function properly, contact your dealer for further advice. General Problems Problem 1: Can't connect to the Wireless Access Point to configure it.
Wireless Access Point User Guide Problem 2: My PC can't connect to the LAN via the Wireless Access Point. Solution 2 Check the following: The SSID and WEP settings on the PC match the settings on the Wireless Access Point. On the PC, the wireless mode is set to "Infrastructure" If using the Access Control feature, the PC's name and address is in the Trusted Stations list. If using 802.1x mode, ensure the PC's 802.1x software is configured correctly.
Appendix C About Wireless LANs C Overview Wireless networks have their own terms and jargon. It is necessary to understand many of these terms in order to configure and operate a Wireless LAN. Wireless LAN Terminology Modes Wireless LANs can work in either of two (2) modes: Ad-hoc Infrastructure Ad-hoc Mode Ad-hoc mode does not require an Access Point or a wired (Ethernet) LAN. Wireless Stations (e.g. notebook PCs with wireless cards) communicate directly with each other.
Wireless Access Point User Guide Different Access Points within an ESS can use different Channels. To reduce interference, it is recommended that adjacent Access Points SHOULD use different channels. As Wireless Stations are physically moved through the area covered by an ESS, they will automatically change to the Access Point which has the least interference or best performance. This capability is called Roaming. (Access Points do not have or require Roaming capabilities.
Appendix C - About Wireless LANs If this option is used: The Access Point must have a "client login" on the Radius Server. Each user must have a "user login" on the Radius Server. Each user's wireless client must support 802.1x and provide the login data when required. All data transmission is encrypted using the WPA standard. Keys are automatically generated, so no key input is required. 802.1x This uses the 802.1x standard for client authentication, and WEP for data encryption.
Appendix D Command Line Interface D Overview If desired, the Command Line Interface (CLI) can be used for configuration. This creates the possibility of creating scripts to perform common configuration changes. The CLI requires a Telnet connection to the Wireless Access Point. Using the CLI - Telnet 1. Start your Telnet client, and establish a connection to the Access Point. e.g. Telnet 192.168.0.228 2. You will be prompted for the user name and password.
Appendix D - Command Line Interface get beaconinterval Display Beacon Interval get channel Display Radio Channel get country Display Country/Domain get defaultkey Display Default Key Index get description Display Access Point Description get dhcp Display DHCP Mode get dhcpserverendip Display DHCP Server End IP Address get dhcpserverstartip Display DHCP Server start IP Address get dnsserver Display IP Address of DNS Server get dot1xdynkeyupdate Display 802.
Wireless Access Point User Guide get psk Display Pre-shared Key get radiusserver Display RADIUS Server IP Address get radiusport Display RADIUS Port Number get radiussecret Display RADIUS Shared Secret get remoteptmp Display PTMP's Remote MAC Address List get remoteptp Display PTP's Remote MAC Address get roguedetect Display Rogue AP Detection Mode get rogueinteval Display Interval of Every Rogue AP Detection get roguelegal Display Legal AP List of Legal AP get roguetrap Display Rogue AP
Appendix D - Command Line Interface get systemname Display Access Point System Name get telnet Display Telnet Mode get time Display Current System Time get timezone Display Time Zone Setting get uptime Display Access Point Up Time get username Display Login User Name get vapname Display Virtual AP Name get version Display Firmware Version get vlan Display VLAN Operational State get vlanid Display the VLAN ID get wirelessmode Display Wireless LAN Mode get wirelessseparate Display Wire
Wireless Access Point User Guide set dnsserver Set DNS Server IP Address set dot1xdynkeyupdate Set 802.1x Dynamic Key Update Mode set dot1xdynkeylife Set 802.1x Dynamic Key Life Time (in Minutes) set dot1xkeytype Set 802.
Appendix D - Command Line Interface set roguelegal Add/Delete Legal AP MAC/OUI set roguesnmp Set Rogue AP Detection SNMP Trap Mode set roguetype Set Rogue AP Definition set rtsthreshold Set RTS/CTS Threshold set security Set Wireless Security Mode set shortpreamble Set Short Preamble set snmpreadcommunity Set SNMP Read Community set snmpwritecommunity Set SNMP Write Community set snmpmode Set SNMP Mode set snmpmanagemode Set SNMP Manager Mode set snmptrapmode Set SNMP Trap Mode set sn
Wireless Access Point User Guide set wmm Set WMM Mode set wmmnoack Set WMM No Acknowledge factoryrestore Restore to Default Factory Settings apply To make the changes take effect exit Quit the telnet 116
