User manual
Table Of Contents
- Welcome Back, Old Friend
- Chapter 1: Getting Started
- Rear Panel Connections
- Setting Up the Prophet-5
- Exploring the Prophet-5
- Chapter 2: Prophet-5 Controls
- Global Settings
- Oscillators
- Mixer
- Filter
- Filter Envelope
- Amplifier Envelope
- Low Frequency Oscillator
- Wheel-Mod Controls
- Poly Mod
- Using the Vintage Knob
- Pitch and Mod Wheels
- Adding Aftertouch
- Glide Rate
- Unison
- Master Tune
- The Release Switch
- The Tune Button
- Key Priority Modes
- Chapter 3: Creating Sounds
- Synth Bass
- Creating Synth Brass
- Creating a Hard-Sync Lead
- Chapter 4: Using CVs and Gates
- Appendix A: Troubleshooting and Support
- Appendix B: Calibrating the Prophet-5
- Appendix C: Exporting and Importing Programs/Banks
- Appendix D: Alternative Tunings
- 1. 12-Tone Equal Temperament (non-erasable)
- 2. Harmonic Series
- 3. Carlos Harmonic Twelve Tone
- 4. Meantone Temperament
- 5. 1/4 Tone Equal Temperament
- 6. 19 Tone Equal Temperament
- 7. 31 Tone Equal Temperament
- 8. Pythagorean C
- 9. Just Intonation in A with 7-Limit Tritone at D#
- 10. 3-5 Lattice in A
- 11. 3-7 Lattice in A
- 12. Other Music 7-Limit Black Keys in C
- 13. Dan Schmidt Pelog/Slendro
- 14. Yamaha Just Major C
- 15. Yamaha Just Minor C
- 16. Harry Partch 11-Limit 43 Note Just Intonation
- 1. 12-Tone Equal Temperament (non-erasable)
- Bookmark 1
- Bookmark 1
33
Prophet-10 User’s Guide
Wheel-Mod Controls
Using LFO and Wheel-Mod
There are many ways to make creative use of the LFO and Wheel-Mod:
• To create vibrato, route the LFO’s triangle wave to freq A and freq B
in the wheel-mod section to create vibrato. Set the LFO frequency to
7 and the initial amount to 3. Make sure wheel-mod source mix is set
to fully counterclockwise to lfo. Using the Mod Wheel intensies the
effect.
• To create a chorusing effect, set osc a and osc b to sawtooth and set
their levels equally in the mixer. Then the LFO’s triangle wave to just
freq B with frequency set to 2 and initial amount set to 3. Make sure
wheel-mod source mix is set to fully counterclockwise to lfo. Using the
Mod Wheel intensies the effect.
• To create trills, route the LFO’s square wave to freq A and freq B in
the wheel-mod section. Set the frequency to 6 and the initial amount to
5. Make sure wheel-mod source mix is set to fully counterclockwise to
lfo. Using the Mod Wheel intensies the effect.
• To create an auto-wah effect, route the LFO’s triangle wave to filter in
the wheel-mod section. Set the frequency to 6 and the initial amount to
5. Then, in the Filter section, set cutoff to 0 and resonance to 5. Make
sure wheel-mod source mix is set to fully counterclockwise to lfo.
Using the Mod Wheel intensies the effect..
• To create subtle harmonic movement, route the LFO’s triangle wave to
filter in the wheel-mod section. Set the frequency to 3 and the initial
amount to 3. Then, in the Filter section, set cutoff to 4 and resonance
to 5. Make sure wheel-mod source mix is set to fully counterclockwise
to lfo. Using the Mod Wheel intensies the effect.