User Manual
Table Of Contents
- Evolver Operation Manual
- Dave Smith Instruments
- 1210 Cabrillo Hwy N
- Half Moon Bay, CA 94019-1449
- For Technical Support, E-mail to:support@davesmithinstruments.com
- Contents
- Quick Start 6
- Basic Operation FAQs 11
- Inside Evolver 12
- Signal Flow Diagram 13
- Main Parameters 14
- Sequencer Operation 18
- Program Parameters 21
- Modulation Destination Table 38
- Modulation Source Table 40
- MIDI Implementation 41
- Welcome…
- Register
- Version 3.0 Notes
- Quick Start
- Program Notes
- Bank 1
- Bank 4
- Programs 80 – 128 are sounds meant to played from a keyboard; some have sequences programmed, and some do not. Most respond in different ways to keyboard pressure and mod wheel.
- Special thanks to Program contributors, including:
- Craig Wiper
- Basic Operation FAQs
- The Analog Side
- The Digital Side
- Sequencer Operation
- While the sequencer is running, if you hold the Shift button when you hit the Stop button, the sequence will continue running until finished (according to the length of Sequence 1), and will stop after playing step 1.
- A simple “tap tempo” feature is available. With the sequencer off, hold the Reset button, and then hold the Start/Stop button for a count of four; then lift up the Start/Stop button in time. The sequencer will start with the new tempo. Note – the actual speed will depend on the Clock Divide setting. The count will match if Clock Divide is set to 4n. If set to 8n, it will play twice as fast as your “tap”, and so forth.
- Program Parameters
- Display
- Destination
- 0ff
- No destination selected
- 01F
- Oscillator 1 Frequency
- 0AL
- Oscillator All Level
- noL
- Noise Level
- El
- External In Level
- 01P
- Oscillator 1 Pulse width
- F43
- Frequency Mod (FM) Amount; Osc 4 -> 3
- F34
- Frequency Mod (FM) Amount; Osc 3 -> 4
- R43
- Ring Mod (Amplitude) Amount; Osc 4 -> 3
- R34
- Ring Mod (Amplitude) Amount; Osc 3 -> 4
- FL
- Lowpass filter frequency
- FLS
- Filter Split –separation between left / right
- Res
- Resonance
- UCA
- VCA amount
- Fbf
- Feedback frequency
- Fba
- Filter Amount
- Dt1
- Delay 1 Time
- DA1
- Delay 1 Amount
- L1f
- LFO 1 Frequency
- L2f
- LFO 2 Frequency
- L3f
- LFO 3 Frequency
- L4f
- LFO 4 Frequency
- Additional Sequencer-Only Modulation Destinations
- Display
- Destination
- CL0
- Sequencer clock (BPM) multiplier
- n0
- MIDI note number
- uel
- MIDI Velocity
- Modulation Sources
- Display
- Source
- 0ff
- No Source selected
- SE1
- Sequence 1
- fen
- Filter Envelope
- MIDI Implementation
- MIDI Messages
- System Exclusive Messages
- 0
- No destination selected
- 1
- Oscillator 1 Frequency
- 10
- Oscillator All Level
- 11
- Noise Level
- 12
- External In Level
- 13
- Oscillator 1 Pulse width
- 16
- Frequency Mod (FM) Amount; Osc 4 -> 3
- 17
- Frequency Mod (FM) Amount; Osc 3 -> 4
- 18
- Ring Mod (Amplitude) Amount; Osc 4 -> 3
- 19
- Ring Mod (Amplitude) Amount; Osc 3 -> 4
- 20
- Filter frequency
- 21
- Filter Split –separation between left / right
- 22
- Resonance
- 23
- Highpass Frequency
- 24
- VCA amount
- 25
- Pan
- 26
- Feedback frequency
- 27
- Feedback Amount
- 28
- Delay Time 1
- 29
- Delay Time 2
- 30
- Delay Time 3
- 31
- Delay Time All
- 32
- Delay Amount 1
- 33
- Delay Amount 2
- 34
- Delay Amount 3
- 35
- Delay Amount All
- 36
- Delay Feedback 1
- 37
- Delay Feedback 2
- 38
- LFO 1 Frequency
- 39
- LFO 2 Frequency
- 40
- LFO 3 Frequency
- 41
- LFO 4 Frequency
- Sequencer only destinations
- 69
- Tempo Clock multiplier
- 70
- MIDI Note Out
- Modulation Sources
- 0
- No Source selected
- 1
- Sequence 1
- 9
- Filter Envelope
Shape: 6 2 see table Selects the LFO waveshape:
Display LFO Shape
tri
Triangle
rsa
Reverse Sawtooth
Sat
Sawtooth
pul
Pulse (square wave)
rnd
Random – changes once per cycle for sample-and-hold
effects
Amount: 6 3 0…100, 1…100 Sets the amount of LFO, 0-100. When you go
past 100, the scale starts over at 1, but now Key Sync is on. This means that this LFO
will restart every time you hit a key.
Destination: 6 4 see table LFO 1 destination - see the Modulation Destination
table on page 38 for a list of possible destinations.
Envelope 3
Envelope 3 is a general purpose envelope for modulation purposes.
Amount: 7 1 -99…+99 Amount of envelope 3
Destination: 7 2 see table Envelope 3 destination - see the Modulation
Destination table on page 38 for a list of possible destinations.
Delay: 7 1 S 0…100 Delay time of Envelope 3, prior to Attack
Attack: 7 3 0…110 Attack time of ADSR envelope generator 3
Decay: 7 4 0…110 Decay time
Sustain: 7 5 0…100 Sustain Level
Release: 7 6 0…110 Release time
Velocity: 7 2 S 0…100 Amount of MIDI velocity controlling the level envelope 3.
31