User Manual
Table Of Contents
- A Few Words of Thanks
- Chapter 1: Getting Started
- Rear Panel Connections
- Setting Up the Pro 3
- Using the Main Display
- Sound Banks
- Editing Programs
- Saving a Program
- Using Paraphonic Mode
- Exploring the Pro 3 in Greater Depth
- Chapter 2: Pro 3 Controls
- Oscillators
- Mixer
- Filters
- Amplifier Envelope
- Auxiliary Envelopes
- Low Frequency Oscillators
- Modulation
- Effects
- Arpeggiator
- Sequencer
- Normal, Gated, and Trigger Modes
- Programming the Sequencer
- Recording Phrases/Sequences A,B,C, or D.
- Sequencing Parameter Changes in Real-Time
- Copying a Sequence from One Track to Another
- Copying and Pasting an Entire Sequence
- Muting a Sequence Track
- Creating An Extended Sequence
- Paraphonic Sequencing
- Adding Rests, Ties, and Velocity
- Editing Duration
- Adding Ratcheting
- Editing Other Elements of a Sequence
- Setting or Changing the Destination of a Track
- Recording Additional Sequencer Tracks for Modulation
- Using Slew
- Turning off the Sequencer’s “Notes” Track
- Sequencer Parameters (Front Panel)
- Additional Sequencer Parameters (Display Menus)
- Cue Program
- Tuned Feedback
- Master Volume/Program Volume
- Transpose
- Hold
- Glide
- Pitch and Mod Wheels
- Touch slider
- Adding Aftertouch
- Distortion
- Play List
- Miscellaneous Parameters
- Global Settings
- Chapter 3: Programming the Pro 3
- Synthesis 101: Synth Bass
- Creating Synth Brass
- Creating a Hard-Sync Lead
- Chapter 4: Using the Pro 3 with External Devices
- Appendix A: Modulation Sources
- Appendix B: Modulation Destinations
- Appendix C: Troubleshooting and Support
- Appendix D: Calibrating the Pro 3
- Appendix E: Alternative Tunings
- Appendix F: MIDI Implementation
- Bookmark 1
- Bookmark 1
137
Pro 3 User’s Guide
Appendix F: MIDI Implementation
See subsequent sections for additional Continuous Controller (CC) and
Non-Registered Parameter Number (NRPN) messages received.
Transmitted Channel Messages
Status Second Third Description
1000 nnnn 0kkkkkkk 0000000
Note Off.
1001 nnnn 0kkkkkkk 0vvvvvvv
Note On.
1011 nnnn 0vvvvvvv 0vvvvvvv
Control Change; see “Transmitted Controller Messages”
1100 nnnn 0ppppppp
Program change, 0-127 for Programs 00-128 within
current Bank
1101 nnnn 0vvvvvvv
Channel Pressure
1110 nnnn 0vvvvvvv 0vvvvvvv
Pitch Bend LS Byte then MS Byte
Notes: 0kkkkkkk Note number 0 — 127
nnnn Channel number 0 to 15 (MIDI channel 1-16).
Ignored if MIDI channel set to ALL
0vvvvvvv Value
Transmitted Controller Messages
Status Second Third Description
1011 nnnn 0000 0001 0vvvvvvv Mod Wheel
1011 nnnn 0000 0010 0vvvvvvv Breath Controller: When assigned to Pedal/CV
1011 nnnn 0000 0100 0vvvvvvv Foot Controller: When assigned to Pedal/CV
1011 nnnn 0000 1101 0vvvvvvv Expression: When assigned to Pedal/CV
1011 nnnn 0000 0111 0vvvvvvv Volume: When assigned to Pedal/CV
1011 nnnn 0100 1010 0vvvvvvv Brightness: Assigned to Pedal/CV
1011 nnnn 0010 0000 0vvvvvvv Bank Select: 0 - 9
1011 nnnn 0100 0000 0vvvvvvv Damper pedal: Sends 0 if o, 0111 1111 when
on
1011 nnnn 0000 0111 0vvvvvvv Volume knob
See sections that follow for additional Continuous Controller (CC) and
Non-Registered Parameter Number (NRPN) messages transmitted.