user manual REALIZE YOUR UBIQUITOUS DREAM Enjoy the ubiquitous mobile broadband service in your daily life
Contents .......................................................... 04 Introduction to the Product ................................................................................... 04 Functional Features Front side of CPE ......................................................................................... 04 Rear side of CPE .......................................................................................... 05 Configuration ...................................................................
Introduction to the Product Thank you for choosing our Indoor VoIP CPE, SWC-5x00W series. The VoIP CPE allows you to share a superior data communication by Ethernet and WiFi network, and to make Voice over Internet Protocol calls. The VoIP CPE comes with easy installation, reliable network connection, advanced security & authentication and mores. Please read this User Guide carefully to learn about SWC-5x00W series. It will help your various communication needs properly served at home and offices.
Rear side of CPE Antenna2 WiMAX Main Power Switch Antenna1 WiMAX Diversity PC Telephone Power Adapter Hardware Reset Item Details External Antenna Antenna1 : WiMAX Diversity Antenna2 : WiMAX Main Antenna3 : WiFi Separable external antenna User external type antenna attachable * Antenna Classification - 2.3G : M23 - 2.5G : M25 - 3.
Configuration Network Configuration Local Network Gateway External Network WiMAX PC Internet Telephone SEOWONINTECH Proprietary-Contents may change without notice To verify the normal operation of the router, check the following LEDs after connecting the router, modem, and PC with a LAN cable, as follows: 06 LED Normal Operation Actions to take if not illuminated PWR ON when connecting adapter Check for adapter power failure LAN1 / LAN2 ON when cable is connected normally Check for adapter
Package Configuration LAN Cable Antenna X 3 Tel Line User Manual Adapter This Document cannot be used without the authorization of SEOWONINTECH Main Unit 07
Configuration PC Configuration (Windows XP) This procedure is used to restore Windows XP’s TCP/IP setup to the default values. If Windows has just been installed for the first time on the PC, no changes should be required, but you should check to confirm that all values are normal according to the following. After completing the TCP/IP setup of the PC, connect PC and CPE with a LAN cable and turn CPE on before Windows starts up to determine whether an IP address is obtained from CPE automatically.
■ Double-click the Local Area Connection from the Network Connection list to select it. Double-click the Local Area Connection Click “Properties” in the Local Area Connection Status window.
Configuration SEOWONINTECH Proprietary-Contents may change without notice ■ 10 Double-click Internet Protocol (TCP/IP) to open its Properties window, and then select “Obtain an IP address automatically” and “Obtain a DNS Server address automatically”. Double-click TCP/IP ■ Select the‘Obtain an IP address automatically’ ‘Obtain a DNS Server address automatically’ and click OK After completing setup, click OK and close all of the Local Area Connection Properties windows.
How to check your IP address ■ To run the Command Prompt, click the Start button at the lower left corner of the Windows screen. Click Run, then enter “cmd” in the Open box, and click OK. Run cmd ■ When the Command Prompt window opens, enter the “ipconfig” command to verify the IP address, Subnet mask, and Gateway, which are automatically assigned to PC.
CPE Built-in Web Server Access The WEB GUI is used to manage a CPE and view its current status. You can access the web server that is built into the CPE, even when not connected to the Internet. To access the web server, open Internet Explorer or your Browser and type “192.168.1.1”, which is the IP address of CPE, in the address bar, as shown below: NOTE If the PC is connected to the CPE but is not connected to the Internet, entering the IP address of 192.168.1.
CPE Setup on the web page LAN Setup ■ Select “LAN” → “LAN Configuration” from the menu. Configure LAN IP address LAN IP address is used in the LAN that the CPE manages. Setup LAN IP address in “IP Address/Subnet Mask” text boxes. Initial Value is “192.168.1.1/255.255.255.0” and only the last byte in “Subnet Mask” box can be modified. ■ Configure DHCP server Enable DHCP server to lease IP address to the computer connecting to CPE with wired LAN.
CPE Setup on the web page SEOWONINTECH Proprietary-Contents may change without notice 02 Status 14 ■ Select “LAN” → “Status” from the menu. ■ You can see the details of the LAN configuration.
Switch Setting 01 Status Select “Switch” → “Status” from the menu. You can see the various configurations related to switch configuration, such as Switch mode and several filters.
CPE Setup on the web page WLAN(WiFi) Setup 01 WiFi Setup WiFi configuration can be modified when Switch mode is Router (NAT) Mode. Be careful when you select WiFi Bridge mode. When WiFi Bridge mode is enabled. Wired LAN and WiFi interfaces are member of a single bridge. Wired LAN and WiFi interfaces have the same MAC address. SEOWONINTECH Proprietary-Contents may change without notice 16 When WiFi Bridge mode is disabled.
NOTE The Wired LAN interface’s IP address can be changed according to the WiFi Bridge mode. If you can’t access SWC-5x00W with WiFi after the modification of WiFi Bridge mode, try to access with “192.168.2.1”. ■ Select “WLAN” → “WiFi Setup” from the menu. ■ Configure WiFi Security Select Authentication Mode(Open, Shared, WPA-PSK, WPA2-PSK) Set whether encryption mode using WEP will be used or not. Set network key if using WEP encryption. ■ Finish setup by clicking “Save”.
CPE Setup on the web page 02 WiFi DHCP SEOWONINTECH Proprietary-Contents may change without notice WiFi DHCP can be configured when WiFi Bridge Mode is disabled. 18 Select “WLAN” → “WiFi DHCP” from the menu. Configure a WiFi IP Address WiFi IP address is used in the wireless LAN that CPE manages. Configure LAN IP address in “IP Address/Subnet Mask” text boxes. Initial Value is “192.168.2.1/255.255.255.0” and only last byte in “Subnet Mask” box can be modified.
■ Select “WLAN” → “Status” from the menu. ■ You can see a lot of information related to the WiFi configuration.
CPE Setup on the web page VoIP Settings 01 Status ■ SEOWONINTECH Proprietary-Contents may change without notice ■ 20 Select “VoIP” → “Status” from the menu. You can see a lot of information related to the VoIP configuration.
Application Setup 01 Firewall ■ Select “Application” → “Firewall” from the menu. ■ If you want to use the Firewall function, check the “Enable” checkbox. ■ Finish setup by clicking the“Apply”button. Then, you will be moved to the Rebooting Screen. ■ Changed configuration is applied immediately. This Document cannot be used without the authorization of SEOWONINTECH Firewall enables you to set the CPE so that it is not affected by external hacking attempts, including Ping Flooding or DoS.
CPE Setup on the web page 02 DMZ & Port Forwarding SEOWONINTECH Proprietary-Contents may change without notice The DMZ feature allows you to specify one computer on your network to be placed outside of NAT firewall. This may be necessary if the NAT feature is causing problems with an application such as a game or video conferencing application. Use this feature on a temporary basis, as the computer in the DMZ is not protected from attacks by hackers.
■ Select “Application” → “DMZ & Port Forwarding” from the menu. ■ Configure DMZ(Demilitarized Zone) Select whether or not to enable the DMZ function. Set the IP address to have all ports opened in “Private LAN IP” content. ■ ■ Finish setup by clicking the “Apply” button. Then, you will be moved to the Rebooting Screen. Configure Port Forwarding The port forwarding function can be configured when DMZ is disabled. Enter the information for Port Forwarding.
CPE Setup on the web page 03 VPN pass through SEOWONINTECH Proprietary-Contents may change without notice The VPN (Virtual Private Network) function is used to obtain access to a security network installed in a company or an organization via the Internet network. If there is a VPN Server outside, and one has access to the VPN Server via the Internet network by using CPE, this screen shows how to activate the security protocol supported by the appropriate VPN Server.
04 UPNP UPnP (Universal Plug and Play) is the standard for automatically detecting each other by using the internet and web protocol when a PC, peripheral devices, intelligent home appliances, or wireless equipment is connected to the network. When a user can add a certain device to the network using UPnP, the device will complete its own organization, receive the TCP/IP address, and discover the HTTP-based discovery protocol to publicize its ■ Select “Application” → “UPNP” from the menu.
CPE Setup on the web page 05 QoS SEOWONINTECH Proprietary-Contents may change without notice QoS (Quality of Service). On the internet or other network, the QoS can measure and improve transmission and error rates. It is a concept of attributes that can be guaranteed to a certain degree. If some high frequency video or multi video information needs to be transmitted consistently, it has a very special meaning.
■ Select “Application” → “QoS” from the menu. ■ To set the QoS, check“Shaping”or“Priority”. The desirable service quality class can be set. ■ Set the priority. ■ Check “Priority” and click “Apply”. The input window will appear. After entering all the inputs necessary for Priority Setting, press the “Add” button to see the added priority. Check the Shaping environment. After entering all the necessary inputs for shaping, press the “Add” button to see the added shaping.
CPE Setup on the web page 06 DDNS SEOWONINTECH Proprietary-Contents may change without notice DDNS (Dynamic DNS) is a method for easily maintaining the DNS information of a PC that uses a dynamic IP address. In general, when a user accesses the internet, the internet service provider arbitrarily assigns one of the IP addresses not used at the moment, and this address is exclusively provided for the user while accessing the internet.
07 MTU ■ Select “Application” → “MTU” from the menu. ■ Set the maximum transmittable packet size. Enter a value between 500 and 1500. Finally, click the “Apply” button to finish setting. This Document cannot be used without the authorization of SEOWONINTECH The MTU (Maximum Transmission Unit) is the maximum sized packet or frame that can be transmitted in a packet or frame-based network such as TCP/IP. In general, the unit of octet is used.
CPE Setup on the web page Admin Setup 01 Version ■ ■ Select “Admin” → “Version” from the menu. You can see the versions of the SWC-5x00W firmware and the WiMAX firmware in use. SEOWONINTECH Proprietary-Contents may change without notice 02 Password 30 Select “Admin” → “Password” from the menu. Set the Password to be given to the Administrator who manages the CPE. ■ Enter the new password, and re-type it to confirm. ■ Finish setup by clicking the “Apply” button.
■ ■ ■ Select “Admin” → “CPE Upgrade” from the menu. Input the CPE firmware path directly, or search for the firmware file by clicking the “Browser” button. To start the firmware update, click “Apply” button.
CPE Setup on the web page ■ This will take several minutes, and time will vary according to the environment. In some case, a pop-up window asking to rebuild the system will be opened due to a version difference. If this occurs, click “Yes” to rebuild the system. SEOWONINTECH Proprietary-Contents may change without notice ■ 32 ■ CPE is rebooted automatically after the upgrade process is complete. Cau- To avoid failure of the CPE, do not power off the CPE during the upgrading process.
04 Reboot/Default Setting Select “Admin” → “Reboot/Default Setting” from the menu. ■ Select “Reboot” to reboot CPE. ■ Select “Reset to all default settings” to reboot CPE and initialize all CPE configuration. ■ To reboot the CPE, click “Apply” button. ■ CPE is rebooted automatically. It takes about 40 seconds.
Trouble Shooting Actions to be taken when the Internet is disconnected 01 Check the status of external type modem. - Check that the Link lamps of cable, modem are illuminated. 02 Check the LED status of CPE. - Check that the POWER LED is illuminated. - Check if the LEDs of WiMAX are illuminated. - For LAN port, check that the lamp of the port connected to the PC is illuminated. 03 Check the IP address of PC.
- Enter [192.168.1.100] for [IP Address], [255.255.255.0] for [Subnet Mask], and [192.168.1.1] for [Default Gateway]. - Click [Use the following DNS Server Address]. - For [Basic Setup DNS Server], enter the communication company server of each country. - Click [OK]. Click [OK] again in the [Local Area Connection Properties] window. For Windows XP For MAC OS X - From the “Apple” menu, Choose “System Preference..“ - Click on the [Network] icon in the [Internet & Network] category.
Operating Information Temperature Range for the SWC-5x00W - Operating temperature for the units is 0 ~ 40 C Power Rating AC for the SWC-5x00W SEOWONINTECH Proprietary-Contents may change without notice - 110-240V ~ 50/60Hz 0.
Safety Information Caution ■ Do not put any object on the product. ■ Avoid heating devices. ■ Never disassemble, repair or redeign the product. ■ Be careful not to let any alien particle get inside the product. ■ Do not leave the Product at a location where static electricity is severe, it can cause malfuction to the product. Do not put any metallic object (coin, hair pin) or flammable object inside the product or drop the product.
Legal Information WEEE Notice The disposal of this device is subject to the Waste from Electrical and Electronic Equipment(WEEE) Diretive of the European Union. The Drective aims to promote environmentally-friendly handling of WEEE by ecological disposal or reuse/refurbishment of the collected WEEE. This symbol on the device signifies that the device ought not to be discarded with mormal household garbage. You are obliged to hand over this device to a certified collection point at the end of its life.
Warranty Information Quality Warranty This product is the result of high-class craftsmanship based on strict quality control procedures. ■ ■ In case of Product failure or malfunction during normal usage, your product will be repaired free of charge within the Limited Warranty period. The Consumer shall bear any labor or parts charges not covered by this Limited Warranty. ■ At the request for repair, you must provide the proof of purchase and the warranty.
Memo
