Use and Care Manual
Your SentrySafe Product
Your SentrySafe product has a number of features to keep your
firearms secure:
Lifetime After-Fire
Replacement
Guarantee
Unbolting Your SentrySafe
Executive Gun Safe
from the Shipping Pallet
Required Tools & Equipment
1
2
3
Remove the handle spoke from the plastic bag attached to
the front of your safe. Screw the spoke into the handle hub
below the lock.
Turn the handle clockwise to open the door of the safe.
Remove the black caps from the
inside bottom of the safe to
reveal the bolts.
Using an 17 mm wrench
remove the nuts in the
bottom of the unit.
NOTE: If the bolts turn when you
begin to remove the nuts, reach
between the slats of the pallet and hold the bolts,
by hand and/or with pliers, as you turn the nuts.
Once the nuts are removed, use a hammer to tap the bolts
through the bottom of the safe.
Close door and put handle in locked position.
With your helper, slide safe to one edge of pallet.
Tip the safe so that the edge moves to the floor.
Remove the pallet and stand the safe upright on the floor.
Replace the black caps on the bottom of the safe to
cover the holes.
Thank you for choosing SentrySafe to help keep your firearms secure and protected.
Please thoroughly read the following instructions to ensure the best experience with your new safe.
Fire-Resistant Executive Gun Safe Owner’s Manual
If your SentrySafe product is in a fire it will be sealed shut
making it necessary for it to be pried open. To help your family
begin again, SentrySafe will ship a replacement free of charge.
To be eligible for the After-Fire Replacement Guarantee you (the
original owner) must register your product using the included
registration form or by visiting SentrySafe.com/MyProfile.
For more information about the Lifetime After-Fire Replacement
Guarantee, visit SentrySafe.com/AfterFireReplacement.
Opening Your Safe
for the First Time
• ETL Verified Fire Protection
• UL Listed Type 1 Digital Lock
• UL Listed Residential Security Container
For more information about your safe, visit SentrySafe.com
Safe Warnings and
Important Information
• SentrySafe recommends that you do not store loaded guns
in this unit.
• If children live of visit your home, do not leave your
Executive Gun Safe open and unattended. Children at play
could accidently be locked inside the safe. Keep your safe closed
and locked at all times.
• Your safe is only part of your total security protection.
SentrySafe recommends that you store your safe in a closet,
office, basement, bedroom or any other location that is convenient
for you but out of direct line of sight from prying eyes.
• DO NOT store pearls in this safe unit. In the event of a fire, the
interior of your safe may reach up to 350˚F. While this temperature
is safe for your paper documents, digital media and other
valuables, pearls can be damaged at much lower temperatures.
• DO NOT store any film based technology or media in
this safe. This product is not intended to protect computer floppy
disks or diskettes, film cartridges, tapes, audio/video cassettes
or photo negatives.
WARNING: This is a two person operation and should not
be attempted without help. Before attempting to unbolt
your new safe, be certain someone is with you to help
steady the safe while you work.
Ensure the safe is standing
upright on a flat, level surface.
• 17 mm wrench
• Hammer
4
5
6
7
8
9
1
2
3
Pull the yellow tab on your lock
to remove the battery tray.
Remove the yellow tab from your
battery tray and insert a 9 volt
alkaline battery into the battery tray.
NOTE: Do not use rechargeable batteries
or any other type of non-alkaline battery. Do not mix old and
new batteries or other types of non-alkaline batteries.
Ensure battery is properly installed before reinserting battery
tray. Reinsert the battery tray into your lock until it clicks
into place.
NOTE: If your lock does not operate properly, don’t press any
buttons for five minutes and try it again.
The yellow lock-out screw tag is located in the
middle of the door jamb. Use the allen wrench
included in the accessories box inside your
safe to remove the lock-out screw.
After the screw is removed, discard and cover
the hole with the black cap also located in
the accessories box.
With the door in the open position, turn
the handle counter-clockwise until it stops,
and enter FACTORY CODE
“1” –“2” –“3” –“4” –“5”–“6” –“#”
into the digital keypad.
The safe will beep two times.
Turn the handle clockwise to the open
position and then counter-clockwise back
into the locked position.
Locate the additional spokes inside the
accessories box and screw them into
the handle hub.
4
5
6
7
8
Instructions
ALWAYS LEAVE THE DOOR OPEN WHEN
CHANGING AND CHECKING CODES.
2
Thank you for choosing SentrySafe!
Merci d’avoir choisi SentrySafe!
¡Gracias por elegir SentrySafe!
11