Product specifications

Part No. 960-000159R_Rev. 1 © 2013, JCM Global, Corporation
8
Sentry® 2.0 Intelligent Bezel Software Guide April, 2013
B RIGHTNESS C ONFIGURATION
For a Banknote Validator that has been disabled, the Attract Brightness slider bar
(Figure 4 b) controls the Sentry 2.0 Display’s disabled Brightness level. The slider
bar can be used to specify a Brightness value ranging from 0 to 255.
REMOTE ACCESS DEVICE SETTINGS
The Handheld Remote Access Device is used to enable the Sentry 2.0 Bezel’s
“Attendant” and “Technician” Modes.
E NABLE /D ISABLE
To enable the Sentry 2.0 Bezel’s Remote capability in the Configuration Utility
Settings field, click to select the
Enable Remote Key Fob check box (Figure 4 c).
By doing so, the Handheld RAD can enter and exit Sentry 2.0 “Attendant” Mode.
Enabling Dual Mode
To enable
“Dual Mode,” click to select the “Tech Access for Attendant” check box.
When Dual Mode is enabled, operating the Handheld Remote Access Device will
allow the Sentry 2.0 Bezel to enter either “Attendant” and/or “Technician” Modes.
BANKNOTE DETECTION
A CCEPTANCE
To test the Sentry 2.0 Bezel’s Acceptance detection:
1. Insert an acceptable Banknote into the Banknote Validator.
2. When accepted, the Sentry 2.0's Screen will display a
"Thank you" response in the
primary Country’s Language.
R EJECTION
To test the Sentry 2.0 Bezel’s Rejection detection:
1. Insert an unacceptable Banknote into the Banknote Validator.
2. When rejected, the Sentry 2.0's Screen will not display
"Thank you".
P LAYER D ENOMINATION S CREEN
To clear displayed denominations, click on the large “Clear Denominations”
button (Figure 5 a).
NOTE: The Screen’s Device field must display as “Connected” to
perform this function (See Figure 5 b).
Part No. 960-000159R_Rev. 1 © 2013, JCM Global, Corporation
21
April, 2013 Software Guide Sentry® 2.0 Intelligent Bezel
TECHNICIAN MODE
In Technician Mode, a Technician can examine the Acceptance Rate and the
Banknote Validator’s Firmware Version. Technician Mode options are displayed
on the Sentry 2.0 Bezel. Use one of the following procedures to enter or exit from
Technician Mode:
E NTER /E XIT T ECHNICIAN M ODE U SING A PC
1. Launch the Sentry 2.0 Download and Configuration Utility software on your PC.
2. Connect a Micro-USB cable between your PC and the Controller Circuit Board
Micro-USB connector.
3. From your PC, click the Configuration Utility’s Diagnostics tab.
4. From the Set Mode field, click the Technician radio button (Figure 8).
E NTER /E XIT T ECHNICIAN M ODE U SING A R EMOTE A CCESS D EVICE (O PTIONAL )
1. Aim the Remote Access Device toward the Sentry 2.0 Bezel.
2. Press the Remote Access Device’s pushbutton.
E NTER /E XIT T ECHNICIAN M ODE VIA THE T ECHNICIAN S WITCH (C IRCUIT B OARD )
• Press the Technician Switch located on the Controller Circuit Board
(Figure 1).
NOTE: To exit from Technician Mode, click the Player or Attendant
radio buttons in the Set Mode field. The Sentry 2.0 reverts to Player
Mode if no other activity occurs for one (1) minute.
NOTE: To exit from Technician Mode, press the Remote Access
Device’s pushbutton again. The Sentry 2.0 reverts from Technician
Mode to Player Mode if no other activity occurs for one (1) minute.
NOTE: In Technician Mode, the Sentry 2.0 reverts to Player Mode if no
other activity occurs for one (1) minute.