Certification Exhibit FCC ID: SDBZIGMOD10 IC: 2220A-ZIGMOD10 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Report Number: 10-0020.W06.11.A Manufacturer: Sensus Metering Systems, Inc. Model: ZIGMOD10 Manual 5015 B.U.
Inline Zigbee Module – User Manual [FCC ID: SDBZIGMOD10, IC: 2220A-ZIGMOD10] Revision 2.1, 20 September, 2010 Sensus USA This document contains proprietary information.
REVISION SUMMARY Date Author Change Description August 14, 2009 BG Baseline September 15, 2009 JAS Corrected Label information and added label Placement September 14, 2010 JAS Corrected antenna gain stipulation from 2 to 0dBi.
Sensus In-Line Zigbee Module – User Manual 1.0 Introduction This document details the installation and usage of the “Sensus In-Line Zigbee Module”. At present the module is designed to work in the Sensus iConA and iConAS electric meters although in future in may work with other electric meter designs. The module is designed to sit between the sensor board and the display board within the electric meter. When a Zigbee module is not installed a ribbon cable connects the sensor and display.
Sensus In-Line Zigbee Module – User Manual 2.0 Installation of the module within an electric meter First remove the meter outer cover. Carefully remove the meter inner cover. Disconnect the ribbon cable from the sensor pcb. Insert the Zigbee board into the connector that the display ribbon has been disconnected from. Insert the free end of the ribbon cable into the connector on the Zigbee module as shown in Figure 1. Add the jumper (short) to position J202 on the sensor board, as shown in Figure 2.
Sensus In-Line Zigbee Module – User Manual Figure 2 – Jumper must be fitted 5
Sensus In-Line Zigbee Module – User Manual 3.0 Module pin-out description Pin Ribbon Connector Number Board Edge Connector Description Description 1 MAINS_SENSE MAINS_SENSE Pass through 2 RELAY_TRIGGER RELAY_TRIGGER Pass through 3 RELAY_SWITCH_SENSE RELAY_SWITCH_SENSE Pass through 4 GROUND EXTRA_CS Ribbon is grounded. Board edge is a 5V active high interrupt line to the Zigbee module.
Sensus In-Line Zigbee Module – User Manual 16 7759_ZX 7759_ZX Sensory Zero Crossing Indictor 17 NOT USED NOT USED 18 NOT USED NOT USED 19 SPI_CLOCK SPI_CLOCK Sensor SPI Clock 20 SPI_DATA_IN SPI_DATA_IN Sensor SPI Data Appendix A General Statements Warning: Changes or modifications to this device not expressly approved by Sensus USA could void the user’s authority to operate the equipment.
Sensus In-Line Zigbee Module – User Manual Appendix B RF Energy Health Hazard Please pay attention to the following warnings: When servicing equipment and selecting a location for the In-Line ZigbeeModule, it is important to note that a minimum distance of 20 cm (7.9 inches) is required between personnel and ZigBee 2 Antenna to comply with a radio-frequency exposure limit of 1.0mW/cm . Professional installation required. The radio equipment described in this guide uses radio frequency transmitters.
Sensus In-Line Zigbee Module – User Manual Appendix C Industry Canada Specific Statements: The term “IC:” before the radio certification number only signifies that industry Canada technical specifications were met. This Class B apparatus meets all the requirements of the Canadian Interference Causing Equipment Regulations.
Sensus In-Line Zigbee Module – User Manual Appendix D Compliance Label and Placement: The ZigBee host shall display the following label to indicate use of the ZigBee module within the unit. Sensus Raleigh, NC 27615 Contains Mod No. ZIGMOD10 Contains FCC ID: SDBZIGMOD10 IC: 2220A-ZIGMOD10 This device complies with Part 15 of the FCC Rules and Industry Canada Requirements.
