User's Manual

mOUNTING
NETWORK CONFIGURATION
An nLight network backbone consists of one or more Bridges and a Gateway communicating
over either a CAT-5 wired or a ZigBee
®
wireless connection. If a wired connection is
required, one of the Bridge’s RJ-45 ports is used. The above diagram illustrates several
common Bridge congurations.
Bridge and power supply mount
directly to a 4” x 4” square box.
4
5
6
7
5
6
7
4
5
6
5
6
1
2
3
4
1
2
3
4
7
5
6
7
8
1
2
3
1
2
3
1
2
3
4
RJ-45 PORT
LEDBUTTON
OPERATIONAL INSTRUCTIONS
Conguring a Bridge is done by pressing the push-button on the side of the unit the
number of times corresponding to the desired function (listed below).
1 = Reset unit
2 = Join an nLight (Sensor Switch) wireless network that is accepting new members. For
5 minutes afterwards, the network will continue to accept other new members.
3 = Allow nLight devices with radios to join the Bridge’s current Sensor Switch wireless
network for 5 minutes.
4 = Disallow other nLight devices with radios from joining current network
5 = Start a new nLight (Sensor Switch) wireless network, and allow new members to
join for 5 minutes.
FCC COmPLIANCE
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation. As per 47 CFR Part 2.1091 (b), (d)(3) this device should generally be used in such a way that a separation distance of at
least 20 cm is normally maintained between the antenna and the body of the user, nearby persons, or other transmitters.
CAUTION: Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
LED FUNCTIONALITY
A LED is provided next to each RJ-45 port in order to provide status information for the Bridge. During normal operation, the will blink
when network trafc is detected. During conguration, the sequence in which the LEDs ash indicates the current state (listed below)
of the Bridge.
STATE: Allowing new network members
LED PATTERN: LED1 + LED4, then LED2 + LED3 (sequence repeats)
STATE: Joining (Starting) a network
LED PATTERN: LED1 (and LED 8 if present) will blink back the number of times the button was
pressed until the radio has joined a network. Once it has joined a network, it will begin blinking the
LED pattern for allowing network joining for 5 minutes.
STATE: Bridge is in Boot-Loader mode (contact Tech Services)
LED PATTERN: LED1 + LED3, then LED2 + LED4
STATE: Reset
LED PATTERN: LED1, then LED2, then LED3, then LED4, then LED3, then LED2, and then LED
1 (repeated several times)
NOTE: The state indicated by the LEDs on Port 1-4 is mirrored on the LEDs on Port 5-8 LEDs (if present).
900 Northrop Road, Wallingford, CT 06492 • 1.800.PASSIVE • FX 203.269.9621 • [e-mail] • www.sensorswitch.com
WARRANTY: Sensor Switch, Inc. warrants these products to be free of defects in manufacture and workmanship for a period
of 60 months. Sensor Switch, Inc., upon prompt notice of such defect will, at its option, provide a Returned Material Authorization
number and repair or replace returned product.
LImITATIONS AND ExCLUSIONS: This Warranty is in full lieu of all other representation and expressed and implied
warranties (including the implied warranties of merchantability and tness for use) and under no circumstances shall Sensor
Switch, Inc. be liable for any incidental or consequential property damages or losses.
®
© Sensor Switch, Inc. 2008
1
2
3
4