Cut Sheet

ManualsBrandsSensor Switch ManualsLighting360° Occupancy Sensor, Ceiling Mount

SPECIFICATIONS

ORDERING INFO

OPTIONS

START-TO-HIGH TIMER (SH)

• Upon power up sensor holds lights on

and high for 20 min

OCCUPANCY CONTROLLED

DIMMING (D)

• Provides dimming outputs to control

0-10 VDC dimmable ballasts

• Provides a second occupancy time-

out period that enables the lights to go

to a dim setting before turning off

• Adjustable max/min dim setting

PHOTOCELL (P)

• Auto set-point calibration

• Two selectable modes of operation

• On/Off mode: Photocell has full

control during periods of occupancy

• Inhibit mode: Photocell can prevent

lights from turning on if adequate

daylight is available, but cannot turn

lights off

347 VAC (347)

• Allows sensor to be powered from

and switch 347 VAC

LOW TEMP/HIGH HUMIDITY (LT)

• Sensor is corrosion resistant to

moisture

• Operates down to -40º F/C

OVERVIEW

Designed for mounting heights of up to 45 ft

(13.72 m), the CMR 6 Series High Bay 360º

occupancy sensor provides Passive Infrared

(PIR) detection over a 15 to 20 ft (4.57 to 6.10

m) radial coverage pattern that overlaps the

areas lit by a typical high bay xture. This line

voltage sensor switches loads directly without

the need for a power pack. The CMR 6 sensor

is ideal for individual on/off control of T5/T8

uorescent lighting. HID bi-level lighting can

also be controlled when the Start-to-High (SH)

option is added to the CMR 6. For multiple xture

control, multiple low voltage CM 6, HM 50, and/

or HM 10 Series High Bay sensors and power

packs are recommended. To control 208/240

VAC and 480 VAC loads use the CMR 6 208

and CMR 6 480 Series sensors respectively. For

lower mounting height applications, CMR 9 or

CMR 10 Series sensors are recommended.

SENSOR OPERATION

The sensor detects changes in the infrared

energy given off by occupants as they move

within the eld-of-view. When occupancy is

detected, a self-contained relay switches the

connected lighting load on. The sensor is line

powered, switches line voltage, and requires no

eld calibration or sensitivity adjustments.

LAMPMAXIMIZER

This sensor also contains patent pending

LampMaximizer technology that allows users

to aggressively target energy savings while still

protecting lamp life. A minimum on timer, factory

set at 15 minutes, helps preserve lamp life by

eliminating all lamp cycles shorter than lamp

warranties specify.

A standard occupancy time delay is also present

that ensures lights turn off (assuming minimum

on timer has elapsed) if no occupancy is

detected. This timer is factory set at 10 minutes

to promote energy savings, but is adjustable

between 30 seconds and 20 minutes. These

adjustments can be done manually, through

the unit’s push-button, or automatically every

two weeks through an advanced mode, called

LampMaximizer+, that determines the optimum

time delay in order to maximize both lamp life

and energy savings. Additionally, this sensor

maintains statistics on total lamp on time and

number of cycles.

HIGH BAY 360º SENSOR

CEILING MOUNT • LINE VOLTAGE • PASSIVE INFRARED (PIR)

CMR 6

FEATURES

100% Digital PIR Detection,

Excellent RF Immunity

360º Coverage Pattern

Self-Contained Relay,

No Power Pack Needed

No Minimum Load Requirements

Interchangeable Hot & Load Wires,

Impossible to Wire Backwards

Push-Button Programmable

Adjustable Time Delays

No Field Calibration or Sensitivity

Adjustments Required

Convenient Test Mode

100 hr Lamp Burn-in Timer

Green LED Indicator

LAMPMAXIMIZER

TECHNOLOGY

• Protects Lamp Life while

Maximizing Energy Savings

• Minimum On Timer (15 min default)

• Occ. Time Delay (10 min defatult)

• LampMaximizer+ Mode -

Optimizes Lamp Life & Energy

Savings (disabled by default)

• Switch Counter (in 1000’s)

• Total Lamp On Time (in khrs)

PHYSICAL SPECS

SIZE 4.55” Dia. (11.56 cm)

1.55” Deep (3.94 cm)

WEIGHT 6 oz

MOUNTING 3.5” Octagon Box

Single Gang Handy Box

COLOR White

ELECTRICAL SPECS

MAXIMUM LOAD

800 W @ 120 VAC

1200 W @ 277 VAC

1500 W @ 347 VAC

MINIMUM LOAD None

MOTOR LOAD 1/4 HP

FREQUENCY 50/60 Hz

DIMMING LOAD Sinks < 20mA;

~40 Ballasts @ .5mA each

ENVIRONMENTAL SPECS

OPERATING TEMP

14º to 160º F (-10º to 71º C)

STORAGE TEMP

-14º to 160º F (-26º to 71º C)

RELATIVE HUMIDITY

20 to 90% non-condensing

SILICONE FREE

ROHS COMPLIANT

START-TO-HIGH TEMP/HUMIDITY

Blank = No STH Blank = None Blank = None Blank = 120/277 VAC Blank = Standard

SH = w/STH D = Occupancy P = Photocell 347 = 347 VAC LT = Low Temp

Controlled

Dimming

VOLTAGE

DIMMING

CMR 6 [START-TO-HIGH] [DIMMING] [PHOTOCELL] [VOLTAGE] [TEMP/HUMIDITY]

PHOTOCELL

C US LISTED

TITLE 24

MADE in U.S.A.

5 YEAR WARRANTY

Summary of content (2 pages)

PAGE 1
® CMR 6 HIGH BAY 360º SENSOR CEILING MOUNT • LINE VOLTAGE • PASSIVE INFRARED (PIR) SPECIFICATIONS FEATURES 100% Digital PIR Detection, Excellent RF Immunity 360º Coverage Pattern Self-Contained Relay, No Power Pack Needed No Minimum Load Requirements Interchangeable Hot & Load Wires, Impossible to Wire Backwards Push-Button Programmable Adjustable Time Delays No Field Calibration or Sensitivity Adjustments Required Convenient Test Mode 100 hr Lamp Burn-in Timer Green LED Indicator LAMPMAXIMIZER®
PAGE 2
Revised 10.29.2010 © 2010 Sensor Switch COVERAGE PATTERN 6 HIGH BAY 360º LENS • Best choice for 15 to 45 ft (4.57 to 13.72 m) mounting heights • 15 to 20 ft (4.57 to 6.10 m) radial coverage overlaps area lit by a typical high bay fixture • Excellent detection of large motion (e.g. walking) up to a 35 ft (10.76 m) mounting height • Excellent detection of extra large motion (e.g. forklifts) up to a 45 ft (13.72 m) mounting height LOW VIEW 0 ft 0m 15 4.6 HIGH VIEW 6 3 0m 3 6 9.1 6 3 0m 3 6 9.