Manualshelf

User Manual

ManualsBrandsSensize ManualsElectronicsSensize Tracker v2 CAT-M
51525354555657585960
Table Of Contents
SARA-R4 series-AT commands manual
UBX-17003787 - R16
7Network service
Page 57 of 401
Parameter Type Description
• 80: 80 ms measurement gap repetition period corresponding to the measurement
gap pattern ID 1 (see Table 8.1.2.1-1 of 3GPP TS 36.133 [83])
<tti_bundling> Number TTi (Transmission Time interval) bundling status:
• 0: off
• 1: on
<NBMsinr> Number Logarithmic value of SINR values expressed in 1/5th of a dB. The range goes from 0 to
250 which translates to a range from -20 dB to 30 dB
<esm_cause> Number ESM cause value as defined in 3GPP TS 24.301 [68]
<emm_state> Number EMM state value as defined in 3GPP TS 24.301 [68]. Allowed values:
• 0: EMM-NULL
• 1: EMM-DEREGISTERED
• 2: EMM-REGISTERED-INITIATED
• 3: EMM-REGISTERED
• 4: EMM-TRACKING-AREA-UPDATING-INITIATED
• 5: EMM-SERVICE-REQUEST-INITIATED
• 6: EMM-DEREGISTERED-INITIATED
• 7: undefined (or invalid)
<tx_pwr> Number TX power value in 1/10 dBm if device is in traffic, 255 otherwise
<drx_cycle_len> Number Idle DRX cycle length in 10 ms radio-frame units
<tmsi> String TMSI in hexadecimal format, with most significant byte first
<P-CID> Number E-UTRAN cell Physical Cell ID; the range is 0-503, 65535 if not known or not
detectable.
<RSRP_value> String Current Reference Signal Received Power (RSRP) expressed in dBm, the range goes
from "-140.00" dBm to "-44.00" dBm.
<RSRQ_value> String Current Reference Signal Received Quality (RSRQ) expressed in dB, the range goes
from "-20.00" dB to "-3.00" dB.
7.9.4Notes
SARA-R412M
• Set the command to <mode>=5 only if the module is not registered on 2G RAT.
7.10Edit Verizon wireless APN table +VZWAPNE
+VZWAPNE
SARA-R404M SARA-R410M-01B SARA-R410M-02B SARA-R410M-52BModules
SARA-N4
Syntax PIN required Settings saved Can be aborted Response time Error referenceAttributes
partial No NVM No - +CME Error
7.10.1Description
Reads and writes the APN table stored in the NVM:
• The set command causes the APN table on the DUT to be overwritten. Only Class 3, 6 and 7 APNs can be
overwritten to any customer defined string.
• The read command queries the APN table that is currently on the DUT, starting from the first entry to the
last; it returns each APN entry in a new line.
7.10.2Syntax
Type Syntax Response Example
Set AT+VZWAPNE=<wapn>,<apncl>,
<apnni>,<apntype>,<apnb>,
<apned>,<apntime>
OK AT+VZWAPNE=1,1,"IMS","IPv6",
"LTE","Enabled",0
OK
Read AT+VZWAPNE? [+VZWAPNE: <apncl>,<apnni>,
<apntype>,<apnb>,<apned>,
<apntime> [..]]
OK
+VZWAPNE: 1,"IMS","IPv4v6","LTE",
"Enabled",0
+VZWAPNE: 2,"VZWADMIN",
"IPv4v6","LTE","Enabled",0