Datasheet

ManualsBrandsSensata Crydom ManualsRelaysSolid State Relay DR45, 1NO, 45A, 600V, Screw Terminal 48 ... 600V 100mA ... 45A

• Output ratings up to 60 Amps at 600 VAC

• Built-in overvoltage protection

• Integral heat sink eliminates the need for complex

thermal calculations

• Cage clamp terminal type accept up to 3 AWG wire size

• IP20 touch-safe housing

• Contactor configuration

• AC or DC control

• C-UL-US Listed and VDE approved

• Plastic injection molding equipment

• Packaging equipment

• Industrial ovens

• Lighting control

• Pump control

• Conveyor drives

• HVAC&R

• Railway vehicles

Features

Applications

PRODUCT SELECTION

Control Voltage 45A

90-280 VAC/VDC DR4560A45x

4-32 VDC

60A

DR4560A60x

DR4560D60xDR4560D45x

| DR45 SERIES

AC SINGLE PHASE OUTPUT DIN RAIL MOUNT SSRS

Page 1

The DR45 is a powerful and compact solid state relay in a DIN rail 45mm wide package with an output rating up to 60 Amps

@ 40°C offering mounting flexibility (on panel or DIN rail) and convenient input connection options. Its high I²t capability

and optional built-in overvoltage protection make it suitable for demanding heating, motion and lighting applications.

Its contactor configuration and large cage clamp terminals allow connecting wires up to 3 AWG size on the output without

the use of any additional accessories making them truly ready-to-use devices, therefore reducing installation cost and

time.

UL Listed and VDE certified, the DR45 is a safe and versatile solid state relay with superior performance when compared to

previous generation and competitor products in similar sized packages.

Introduction

www.sensata.com

Summary of content (6 pages)

PAGE 1
| DR45 SERIES AC SINGLE PHASE OUTPUT DIN RAIL MOUNT SSRS Introduction The DR45 is a powerful and compact solid state relay in a DIN rail 45mm wide package with an output rating up to 60 Amps @ 40°C offering mounting flexibility (on panel or DIN rail) and convenient input connection options. Its high I²t capability and optional built-in overvoltage protection make it suitable for demanding heating, motion and lighting applications.
PAGE 2
ORDERING OPTIONS DR45 60 A 45 R P J Series DR45 Operating Voltage 60: 48-600 VAC Control Voltage (1) A: 90-280 VAC/VDC D: 4-32 VDC Rated Load Current 45: 45 Amps 60: 60 Amps Switching Type Blank: Zero Voltage Turn-On R: Instantaneous Turn-On (Motor Rating Certified) Overvoltage Protection Blank: Not Included P: Included Input Connector Blank: Screw Terminal J: Spring Terminal Required for valid part number For options only and not required for valid part number OUTPUT SPECIFICATIONS (2) Description
PAGE 3
GENERAL SPECIFICATIONS (2) Description Parameters Dielectric Strength, Input to Output (50/60Hz) Dielectric Strength, Input/Output to Case (50/60Hz) Minimum Insulation Resistance (@ 500 VDC) Maximum Capacitance, Input/Output Ambient Operating Temperature Range Ambient Storage Temperature Range (7) Short Circuit Current Rating (8) Weight (typical) Housing Material Heat Sink Material DIN Rail Clip Material Hardware Finish Input Terminal Screw Torque Range (lb-in/Nm) Load Terminal Screw Torque Range (lb-in/N
PAGE 4
EQUIVALENT CIRCUIT BLOCK DIAGRAMS/WIRING DIAGRAMS DC Control * TVS option available in “P” version +3/A1 Trigger Circuit OUTPUT DC V - 1/L1 INPUT + * 2/T1 -4/A2 Current Limiter AC/DC Control Load A V AC B Load Load can be wired in position A or B * TVS option available in “P” version Current Limiter +3/A1 AC/DC Converter Trigger Circuit OUTPUT -/ V INPUT AC/DC 1/L1 Load A +/ * -4/A2 2/T1 V AC B Load Load can be wired in position A or B INSTALLATION INSTRUCTIONS Mounting on D
PAGE 5
MECHANICAL SPECIFICATIONS Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] 1.43 [36.4] 2.94 [74.8] 3.62 [92] 1.88 [47.8] 4.39 [111.5] 0.91 [23.1] 1.77 [45] 5.36 [136] 6.08 [154.
PAGE 6
AGENCY APPROVALS, CONFORMANCES, ENVIRONMENTAL AND EMC Approvals (Tested and Certified according To) REG-Nr. xxxxxx E116949 UL 508 and C22.2 No.