Datasheet

ManualsBrandsSensata Crydom ManualsRelaysSolid State Relay Single Phase Power Plus DC, SPST-NO, 20A, 72V, Screw Terminal

Power Plus DC Series

• Ratings from 10A to 100A @ 100 VDC

• LED Status Indicator

• Relays are easily paralleled for higher-current

applications

• UL Approved, CE Compliant to EN60950-1

• Improved SEMS screw and washer

• Redesigned housing with anti-rotation barriers

For Generation 3 datasheet click here

• Mosfet Output

• DC control

• EMC Compliant to Level 3

• Epoxy Free Design

• Optional IP20 Cover

• PWM to 1K Hz

PRODUCT SELECTION

Control Voltage 10A 20A 40A 60A 80A 100A

4-32 VDC DC100D10 DC100D20 DC100D40 DC100D60 DC100D80 DC100D100

AVAILABLE OPTIONS

Not all part number combinations are available.

Contact Crydom Technical Support for information on

the availability of a specific part number.

Required for valid part number

For options only and not required for valid part number

Series

Operating Voltage

100: 1-100 VDC

Thermal Pad

Blank:

Not Included

H: Included

Control Voltage

D: 4-32 VDC

Cover

Blank: Not Included (IP00)

C: Included (IP20)

Rated Load Current

10: 10 Amps

20: 20 Amps

40: 40 Amps

60: 60 Amps

80: 80 Amps

DC D100 HC40

Termination

Blank: Screws & clamps

K: Installed standoffs with (1)

screws for PC Board

mounting (IP00 only)

100: 100 Amps

OUTPUT SPECIFICATIONS

(2)

Description 100A60A20A

Recommended Operating Voltage [Vdc] 1-72 1-72 1-72

Absolute Maximing Rating [Vdc] 100 100 100

Maximum Off-State Leakage Current @ Rated Voltage [mA] 0.1 0.1 0.1

Maximum Load Current [Adc]

(1)(3) 20 60 100

Minimum Load Current [mA]

(4) 2.5 2.5 2.5

Maximum Surge Current (10msec) [Adc] 91 180 330

Maximum On-State Voltage Drop @ Rated Current [Vdc] 0.24 0.36 0.4

Maximum On-State Resistance [RDS-ON] [mΩ] 12 6 4

Thermal Resistance Junction to Case (Rjc) [°C/W] 0.73 0.45 0.27

Minimum Heat Sink for Rated Current @ 40°C [°C/W] 5 1 0.5

80A40A10A

1-72 1-72 1-72

100 100 100

0.1 0.1 0.1

10 40 80

2.5 2.5 2.5

66 136 220

0.13 0.28 0.40

13 7 5

1.27 0.58 0.34

N/R 2 0.5

Maximum Pulse Width Modulation Frequency [Hz] (5) 1000 900 700

1000 900 700

INPUT SPECIFICATIONS

(2)

Description DC Control

Control Voltage Range 4-32 VDC

Maximum Reverse Voltage -32 VDC

Minimum Turn-On Voltage (6) 4 VDC

Must Turn-Off Voltage 1 VDC

Minimum Input Current (for on-state) 11 mA

Maximum Input Current 14 mA

Nominal Input Impedance Current Regulated

Maximum Turn-On Time [µsec] 75

Maximum Turn-Off Time [µsec] 150

Do not forget to visit us at: www.crydom.com

Datasheet

Panel Mount

Summary of content (8 pages)

PAGE 1
Panel Mount Datasheet Power Plus DC Series • Ratings from 10A to 100A @ 100 VDC • LED Status Indicator • Relays are easily paralleled for higher-current applications • UL Approved, CE Compliant to EN60950-1 • Improved SEMS screw and washer • Redesigned housing with anti-rotation barriers • Mosfet Output • DC control • EMC Compliant to Level 3 • Epoxy Free Design • Optional IP20 Cover • PWM to 1K Hz For Generation 3 datasheet click here PRODUCT SELECTION Control Voltage 4-32 VDC 10A 20A 40A 60A 80A
PAGE 2
Panel Mount Datasheet GENERAL SPECIFICATIONS (2) Description Parameters Dielectric Strength, Input/Output/Base (50/60Hz) Minimum Insulation Resistance (@ 500 VDC) Maximum Capacitance, Input/Output Ambient Operating Temperature Range (7) Ambient Storage Temperature Range Weight (typical) Housing Material Hardware Finish Baseplate Material Input Terminal Screw Torque Range (in-lb/Nm) Load Terminal Screw Torque Range (in-lb/Nm) SSR Mounting Screw Torque Range (in-lb/Nm) Input/Load Terminal Screw Torque Range
PAGE 3
Panel Mount Datasheet MECHANICAL SPECIFICATIONS (2) Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] Screw Termination 1.1 [27.9] 0.49 [12.4] 1 1.88 [47.6] OUTPUT INPUT 1.1 [27.9] 0.49 [12.4] 0.89 [22.6] Mounting Hole/Slot 0.19 [4.9] DIA. +2 1 2.25 [57.3] 1.7 [43.2] S O L I D S TAT E R E L AY 4 Hex Standoff Termination (“K” Option) (1) 1.88 [47.6] INPUT 1.0 [25.4] 1.0 [25.4] 1.75 [44.5] 1.75 [44.5] 1.1 [27.9] 0.49 [12.4] 1.7 [43.2] 1.75 [44.5] 2.25 [57.
PAGE 4
Panel Mount Datasheet SURGE CURRENT INFORMATION Single Pulse (i) Duty Factor (10%) (ii) DC100D10 100 Surge Current (Amp) Surge Current (Amp) 60 40 20 75 50 25 0 0.1 1 10 100 1000 0.1 DC100D40 10 100 1000 DC100D60 350 300 Surge Current (Amp) 250 200 150 100 50 250 200 150 100 50 0.1 1 10 100 Surge Duration (msec) 0 1000 10 100 1000 Surge Duration (msec) DC100D80 600 550 500 450 400 350 300 250 200 150 100 50 0 1 0.
PAGE 5
Panel Mount Datasheet THERMAL DERATE INFORMATION (iii) SSR metal base plate acting as heat sink, it must be exposed to free ambient air.
PAGE 6
Panel Mount Datasheet AGENCY APPROVALS EN60950-1: Meets the requirements of sections1.5: 1,7: 2.9: 2.10.5.3: 4.2: 4.5: 4.7: IEC 61000-4-2 Electrostatic Discharge Level 3 IEC 61000-4-4 Electrically Fast Transients Level 3 IEC 61000-4-5 Electrical Surges Level 3 E116950 ACCESORIES Recommended Accessories New Accessories! Protective Cover & Hardware Kits Protective Cover Part number: KS101 Clear plastic cover compatible with all new S1 designs.
PAGE 7
Panel Mount Datasheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. • Disconnect all power before installing or working with this equipment. • Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. • Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo.
PAGE 8
Panel Mount Datasheet ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.