Product guide

Accessories
& Sensors
Accessories
& Sensors
52 WWW.SENSAPHONE.COM
WWW.SENSAPHONE.COM
53
General Accessories
SENSAPHONE
Monitoring Sensor
Specifications
Description
Package Contents
Specifications
Description
Package Contents
(1) Dual setback thermostat
(1) Instruction booklet
(1) Hardware mounting kit
Dual Setback Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-0064
12VDC Power Supply for Dual Setback Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . XFR-0024
Power Supply:
2 AA alkaline batteries
Connection:
2, 3, 4 or 5 wires
Maximum Load:
1.5 A / 30 VAC per output
Number of programs:
4 programs per day, 28
programs
Heat setting range:
40° to 85°F (5° to 30°C)
A/C setting range:
60° to 105°F (16° to 40°C)
Compatibility:
400 and 800
*Specifications subject to change
without notice
For use exclusively with the Sensaphone 400 and 800, this is a “setback” thermostat with
an LCD readout. It lets you enter the desired setpoint for both your “away” and “home”
temperatures. A control signal, sent from your Sensaphone, switches between these two
settings.
Dual Setback Thermostat
Magnetic Reed Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-0006
(1) Sensor
(1) Spacer
(1) Sensor casing
(1) Magnet
(4) Mounting screws
(1) Installation instructions
Dimensions:
Part w/ screw terminals:
2.5” x .75”
x .5”
63mm x 19mm x 13mm
Part w/ magnet:
2.5 ” x .75”
x .625”
63mm x 19mm x 16mm
Housing:
White plastic
Compatibility:
All Sensaphone models
*Specifications subject to change
without notice
The magnetic reed switch may be used with all Sensaphone models to detect any unauthorized
entry or intrusion. They are usually installed on doors and windows to detect their opening and
closing. Several magnetic reed switches may be wired in series.
Magnetic Reed Switch
General Accessories
SENSAPHONE
Monitoring Sensor
Specifications
Description
Package Contents
Specifications
Description
Package Contents
(1) Carbon dioxide sensor
(1) Installation instructions
Carbon Dioxide Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-0068
CO
2
Range:
0-2,000 PPM
Accuracy:
± 50 PPM
Operating Temp Range:
32° to 122°F (0° to 50°C)
Response Time:
2 Minutes for 90% step
change
Housing:
White plastic
Compatibility:
1400, 1800, 2000, 2800,
Express II, SCADA 3000
WEB600 and CELL682.
*Specifications subject to change
without notice
The Sensaphone Carbon Dioxide sensor will allow you to monitor levels of Carbon Dioxide
from 0-2,000ppm with any Sensaphone that will accept a 4-20mA input signal. The sensor will
need a 24VDC power supply to operate (Part # FGD-0053)
Carbon Dioxide (CO
2
)Sensor
Surge Suppressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-0067
(1) Surge suppressor
(1) 6-ft telephone cord
(1) Instruction manual with
warranty information
Voltage Compatibility:
120 VAC
Output capacity:
15 Amps
AC Suppression joule
rating:
1050 joules
Diagnostic LEDs:
Two built in LEDs confirm
suppressor “protection
present” and outlet
“grounded” status
Clamping voltage:
150V
Unit Dimensions:
3.5” x 2.5” x 1.75”
89mm x 63mm x 44mm
*Specifications subject to change
without notice
The Traveler surge suppressor offers complete AC and phone line surge suppression for your
Sensaphone and other electronic devices. The compact housing weighs less than 4 ounces. The
retractable plug prevents scratching of expensive portable electronics. A set of RJ11 telephone
line suppression jacks protect dialup and voice/modem lines. The suppressor offers 2 total
outlets in a space saving direct plug-in format and diagnostic LEDs to warn of wiring problems
and suppressor damage. $50,000 Ultimate Lifetime Insurance (USA & Canada Only).
Surge Suppressor for both Power and Phone