Product guide

Accessories
& Sensors
Accessories
& Sensors
50 WWW.SENSAPHONE.COM
WWW.SENSAPHONE.COM
51
General Accessories
SENSAPHONE
Monitoring Sensor
Specifications
Description
Package Contents
Specifications
Description
Package Contents
Spot Water Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-0013
(1) Spot water detector
(1) Installation instructions
(1) 8’ wire
Normality:
Normally closed
Number per input:
Multiple, wired in series
Dimensions:
2.25” x 1.125” x 3.625”
57mm x 28mm x 92mm
Housing:
Black Plastic
Compatibility:
All Sensaphone models
*Specifications subject to change
without notice
The water detection sensor can be used with all Sensaphone models to detect the presence
of water on a horizontal surface. Independently powered by internal lithium batteries. The
batteries should last for approximately 3-5 years. When the batteries start to run down, the
sensor will automatically cause an alarm dial out when no water is present. Multiple sensors
can be wired in series to a single input.
Spot Water Detector
Normality:
Normally Closed
Number per input:
5
Dimensions:
5.48” x 3.3” x 1.35”
Housing:
Black plastic
Compatibility:
All Sensaphone models
*Specifications subject to change
without notice
The Sensaphone zone water detector is for detecting the presence of water on a floor or in a
false ceiling. It comes with 10’ of WaterRope capable of covering a larger area than the
FGD-0013 water sensor. Up to ten WaterRopes can be cascaded from a single sensor for
even greater coverage. Works with all Sensaphone products and operates on two AA batteries
(installed).
(1) Zone water detector
(1) 10’ of WaterRope
(5) Adhesive cable clamps
(1) Wall mounting kit
(4) Rubber feet
Zone Water Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-0056
Zone Water Detector
General Accessories
SENSAPHONE
Monitoring Sensor
Specifications
Description
Package Contents
Specifications
Description
Package Contents
Infra–Red Motion Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-0007
(1) Infra–Red motion detector
(2) AA batteries
(1) Installation instructions
Dimensions:
4” x 6” x 1.5”
101mm x 152mm x 38mm
Housing:
White plastic
Normality:
Normally closed
Range:
Approximately 40’
Battery Life:
3-5 years
Compatibility:
All Sensaphone models
*Specifications subject to change
without notice
The passive infra-red motion detector can be used with all Sensaphone models to monitor the
movement of warm bodies in a specific area. It will cause an alarm if motion is detected. Its
range of detection covers approximately forty feet of area. Multiple sensors can be wired in
series to a single output.
Infra–Red Motion Detector
Smoke Detector 110V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-0049
Smoke Detector 110V w/battery backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-0049-B
Smoke Detector 220V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-0049-220V
(1) Smoke detector
(1) Wiring harness
(1) Mounting template
(1) Instruction manual
Dimensions:
6.5” diameter x 2.625”
165mm x 67mm
Weight:
6.5
ounces (3kg)
Housing:
White plastic
Operating Temp Range:
40° to 100°F (4° to 37°C)
Compatibility:
All Sensaphone models
*Specifications subject to change
without notice
The Smoke Detector with built-in relay utilizes a photoelectric sensing method and is designed
for use in commercial and residential applications. The device requires hard–wired 120VAC
60Hz power (220VAC 50 Hz optional). The detector features two sets of dry alarm contacts:
one form-A SPST and one form-C SPDT. The detector has tandem interconnect capability
allowing up to 6 devices to be connected together. A 90dBA audible horn is included.
Also available with optional battery backup or in 220V. The detector can be used with all
Sensaphone models.
Smoke Detector