Specifications

Accessories & Sensors
48 www.sensaphone.com
Sensaphone Accessories
Accessory
Series
Multi-Point Wireless I/O Accessory
4-20mA
Series
J Type Thermocouple / 4-20mA Converter
The Multi-Point Wireless I/O System is ideal for connecting dry contacts and/or a 4-20mA
transducer to a Sensaphone that is too far (or too expensive) to run cable. The system will replicate
these sensors up to a distance of 600’ indoors or up to 4 miles line of site ( at terrain, raised
antennas). The system includes a matched 1 Watt 900MHz transmitter and receiver. Two 24V
power supplies and omni-directional antennas are included.
The thermocouple to 4-20mA converter is useful when you need to monitor very high or very
low temperatures that can not be monitored with a standard Sensaphone temperature sensor.
Thermocouples are available in a variety of packages that may be perfectly suited to your
measuring application. The device can be used with any Sensaphone that supports 4-20mA inputs.
Thermocouple sold separate.
The XLink allows your Sensaphone to dial and receive calls using any cell phone with Bluetooth
technology. It provides telephone service to a Sensaphone by placing a cell phone next to the device.
The XLink will send all incoming calls to the Sensaphone and when the Sensaphone needs to dial
out, the call will be seamlessly completed through the cell phone.
This surge suppressor offers complete AC and phone line surge suppression. The retractable plug
prevents scratching of expensive portable electronics. A set of two RJ11 telephone line suppression
jacks protect dialup and voice/modem lines. The suppressor offers two total outlets in a space
saving direct plug-in format and diagnostic LEDs to warn of problems.
Part Name Part Number
Multi-Point Wireless I/O Accessory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-0205
Part Name Part Number
J Type Thermocouple / 4-20mA Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-0220
Part Name Part Number
Bluetooth Cell Phone Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-0230
Part Name Part Number
Surge Suppressor for Power & Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-0067
Accessory
Series
Bluetooth Cell Phone Interface
Accessory
Series
Surge Suppresor for Power & Phone
Sensaphone SCADA 3000 Accessories
SCADA
3000
SCADA 3000 Universal Input Expansion Module
SCADA
3000
SCADA 3000 Pulse Count Module
The SCADA 3000 Universal Input Module is an optional component for use with the SCADA
3000 system. The input channels are identical to those included on the SCADA 3000 main unit.
The Universal Input Module features eight channels that can be con gured to interface with
several different types of sensors and transducers, including: Normally Open/Normally Closed dry
contacts, digital logic, run time accumulation, 0–5V analog, 4–20mA analog and 10K thermistor
(ºC & ºF).
The SCADA 3000 Pulse Count Module features four totalizing pulse count channels and four virtual
channels that can be programmed to calculate various rates or to display count over ow. The four
pulse count channels are capable of counting pulses at a rate of up to 10,000 pulses per second
(10KHz). Each channel will totalize pulses up to one million and then reset to zero. The four virtual
channels can be programmed to calculate the pulse as either pulses per second, pulses per minute,
or pulses per hour.
The SCADA 3000 Relay Output Module is an optional component for use with the SCADA 3000
system. The output channels are identical to those included on the SCADA 3000 main unit. The
Relay Output Module features eight latching relay outputs that can be used to switch equipment
on and off. The relays are rated at 2 Amps at 125VAC and have integral contact protection. They
may be controlled manually or automatically via a ladder program or C-program. In addition, a
microprocessor watchdog circuit is integrated to maintain system reliability. LED indicators are
provided to show system power and module operation via a blinking pulse LED.
The SCADA 3000 Analog Output Module features four analog output signals that can be con gured
as 4–20mA, 0–20mA, or 0–10V. The outputs can be used to control equipment, drive digital
displays, or provide information to other computer devices. The individual outputs are capable of
driving up to 1000 Ohms. They may be controlled automatically via a ladder program or C-program.
The module also features a microprocessor watchdog circuit to maintain system reliability. LED
indicators are provided to show system power and module operation via a blinking pulse LED.
Part Name Part Number
SCADA 3000 Universal Input Expansion Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-3010
Part Name Part Number
SCADA 3000 Pulse Count Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-3020
Part Name Part Number
SCADA 3000 Relay Output Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-3040
Part Name Part Number
SCADA 3000 Analog Output Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FGD-3050
SCADA
3000
SCADA 3000 Relay Output Module
SCADA
3000
SCADA 3000 Analog Output Module