User`s guide

91

Error Code Displayed Reason for error Possible remedy
e248
PPC4000 FAULT
Main processor failure Replace PPC4000
e249
PPC4000 FAULT
External watchdog timer malfunction Replace PPC4000
e250
PPC4000 FAULT
PPC4000 Internal Error Replace PPC4000
e251 SENSOR4 UNDER RNG PCV input is under 2mA Defective sensor or check wiring
e252 SENSOR4 OVER RNG PCV input is over 22mA Defective sensor or check wiring
e253 SENSOR4 UNDER RNG PCV input is under 2mA Defective sensor or check wiring
e254 SENSOR4 OVER RNG PCV input is over 22mA Defective sensor or check wiring
e255 NOT COMMISSIONED
User restored a file from the SD card that
has not been verified
Recommission current profile
e256
VFD1 OFF RATIO
VFD input is moving too slow to meet timeout Check VFD for proper setup
e257
VFD2 OFF RATIO
VFD input is moving too slow to meet timeout Check VFD for proper setup
e258 VFD BOARD FAULT VFD Board is missing or CPU is not programmed Replace VFD Board
e259
PPC4000 FAULT
VFD Board communication problem Replace VFD Board or PPC4000
e260
VFD1 MISSING
VFD was commissioned to current profile but is
not available
Replace VFD Board or fix VFD 1 use in setup
e261
VFD2 MISSING
VFD was commissioned to current profile but is
not available
Replace VFD Board or fix VFD 2 use in setup
e262
to
e265
Unused Unused
e266
VFD BOARD FAULT
VFD Board CPU error Replace VFD Board
e267
VFD BOARD FAULT
VFD Board CPU error Replace VFD Board
e268
VFD BOARD FAULT
VFD Board CPU error Replace VFD Board
e269
VFD BOARD FAULT
VFD Board CPU error Replace VFD Board
e270
VFD BOARD FAULT
VFD Board CPU error Replace VFD Board
e271
VFD BOARD FAULT
VFD Board CPU error Replace VFD Board
e272
VFD1 INPUT BELOW 4mA
VFD 1 input is less than 2 mA Defective input or check wiring
e273
VFD BOARD FAULT
VFD Board CPU error Replace VFD Board
e274
VFD BOARD FAULT
VFD Board CPU error Replace VFD Board
e275
VFD BOARD FAULT
VFD Board CPU error Replace VFD Board
e276
VFD BOARD FAULT
VFD Board has not been calibrated Replace VFD Board
e277
VFD BOARD FAULT
VFD Board CPU error Replace VFD Board
e278
VFD2 INPUT BELOW 4mA
VFD 2 input is less than 2 mA Defective input or check wiring
e279
VFD BOARD FAULT
VFD Board CPU error Replace VFD Board
e280
VFD BOARD FAULT
VFD Board communication problem Replace VFD Board or PPC4000
e281
CHECK VFD1 INPUT
VFD 1 input is either under 2mA either over 21mA Defective input or check wiring
e282
CHECK VFD2 INPUT
VFD 2 input is either under 2mA either over 21mA Defective input or check wiring
e283 P0 NOT COMMISSIONED p00 not commissioned Commission the p00 servo positions
e284 PPC4000 FAULT PPC4000 main CPU timing error Replace PPC4000 (notify Fireye about this error)
e285 PPC4000 FAULT PPC4000 main CPU timing error Replace PPC4000 (notify Fireye about this error)
e286 PPC4000 FAULT PPC4000 main CPU timing error Replace PPC4000 (notify Fireye about this error)
e287 PPC4000 FAULT PPC4000 main CPU timing error Replace PPC4000 (notify Fireye about this error)
e288 PPC4000 FAULT PPC4000 main CPU timing error Replace PPC4000 (notify Fireye about this error)