Instruction manual Set 860
Table Of Contents
- Important safety instructions
- Package contents
- Product overview
- Putting the Set 860 into operation
- Setting up the transmitter
- Connecting the transmitter to an audio source
- Connecting the transmitter to the power supply system
- Charging the stethoset receiver’s rechargeable battery
- Displaying the remaining operating time of the rechargeable battery
- Using the charging reminder function
- Selecting and replacing the ear pads
- Using the Set 860
- Cleaning and maintaining the Set 860
- Using additional functions
- If a problem occurs ...
- Specifications
- Manufacturer Declarations
- Warranty
- In compliance with the following requirements
- Statements regarding FCC and Industry Canada
- RF Radiation Exposure Information
- Information sur l’exposition aux rayonnements radio fréquence (RF)
- Cet émetteur ne doit pas être positionné à proximité d‘une autre antenne ou d‘un autre émetteur, ni utilisé avec une autre antenne ou un autre émetteur.
- Trademarks
If a problem occurs ...
Set 860 | 37
If a problem occurs that is not listed in the above table or if the problem cannot be solved with the
proposed solutions, visit the Set 860 product page at www.sennheiser.com for the most up-to-date
list of frequently asked questions.
You may also contact your local Sennheiser partner for assistance. To find a Sennheiser partner in your
country, search at www.sennheiser.com.
Sound only on
one ear
The balance is misadjusted. Adjust the balance. 23
The audio cable is not properly con-
nected.
Check the audio plug connection. 11
The TV has only a mono headphone
socket.
Use an adapter (mono to stereo jack
socket) to connect the transmitter to
the TV.
–
Sound is less
spatial
Mono operation is activated. Activate stereo operation. 30
Sound is dis-
torted
The audio cable is defective. Replace the audio cable. –
The signal of the audio source is
distorted.
Reduce the volume of the audio
source.
–
The volume on the stethoset
receiver is adjusted too high.
Reduce the volume on the stethoset
receiver.
22
You hear echoes
when using the
stethoset
receiver with a
TV
Some TVs can adjust a delay or
latency of the audio signal for the
digital audio output.
Check the audio output settings of
your TV and set the latency to “0”.
–
The battery
status display
goes off
The battery status display is set so
that it goes off after 30 seconds.
Set the battery status display so that
it is permanently displayed.
32
More than one stethoset receiver is
currently connected to the trans-
mitter.
This function is only possible when
only one stethoset receiver/receiver is
connected to the transmitter.
–
2 beeps during
operation
The rechargeable battery is almost
empty.
Recharge the rechargeable battery. 16
The operating
time decreases
The rechargeable battery is
exhausted.
Have the rechargeable battery
replaced by an authorized Sennheiser
service partner.
28
A hearing pro-
file, the balance
or stereo/mono
operation
cannot be acti-
vated or
changed
The settings protection function is
activated.
Deactivate the settings protection
function (for the hearing profile, the
balance and stereo/mono operation).
33
More than one stethoset receiver/
receiver is currently connected to
the transmitter.
This function is only possible when
only one stethoset receiver/receiver is
connected to the transmitter.
–
The stethoset
receiver does
not connect to
the transmitter
The stethoset receiver is not paired
with the transmitter.
Pair the stethoset receiver with the
transmitter.
29
The distance to the transmitter is
too large.
Reduce the distance between the ste-
thoset receiver and the transmitter.
–
4 stethoset receivers are currently
connected to the transmitter.
Up to 4 stethoset receivers can be
simultaneously used with the trans-
mitter.
–
Problem Possible cause Possible solution Page