SA51 TV Mount English User Manual FULL MOTION FLAT PANEL TV MOUNT 37”-80” 130 lbs +14°/-8° 75x75 ~ 800x450 ±80° 94-203 cm www.senecaav.com 59 kg VESA 3.2”-20” (8.
Table of Contents Table of Contents / Introduction . . . . . . . . . . . . . . 2 Supplied Parts & Hardware . . . . . . . . . . . . . . . . . . . 3 Setup - Step 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Setup - Step 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Setup - Steps 3 to 4 . . . . . . . . . . . . . . . . . . . . . . . . . 6 Setup - Steps 5 to 6 . . . . . . . . . . . . . . . . . . . . . . . . . 7 Other Seneca AV Products . . . . . . . . . . . . . . . . .
Supplied Parts and Hardware x4 A: M5 x 12mm Bolt x4 B: M6 x 12mm Bolt x4 C: M8 x 25mm Bolt x4 D: M5 x 30mm Bolt x4 E: M6 x 35mm Bolt x4 x4 G: M5/M6 14mm Plastic Spacer x8 H: M5/M6/M8 10mm Plastic Spacer x2 R: TV Bracket x4 I: M5/M6/M8 5mm Plastic Spacer x4 J: M5/M6 Washer TIP: - Before drilling tape over each hole to minimize the amount of dust - Avant de bande sur chaque trou de forage àréduire la quantité de poussière - Antes de perforar coloque cinta adhesiva sobre cada agujero para reducir a
Step 1: Attach TV Brackets There are a wide variety of TVs available that use an assortment of bolt sizes. We provide a selection of mounting bolts to fit most TVs. If you have any concerns about this mounting hardware or installation call Seneca AV directly at 1-855-430-4708 or email support@senecaav.com. Step 1.1 Select the correct size of bolt Seneca AV provides 3 bolt diameters (Metric sizes M5, M6 and M8) in various lengths. Part items: A, B, C, D, E, or F.
Step 2: Mount Wall Plate Before you start drilling, attach the wall plate template to your wall. It will make marking and drilling level pilot holes easier, and catch a lot of the dust. Remember to remove it before you attach the wall plate. Wood Stud Wall Brick or Concrete Wall The wall plate must be mounted to two wood studs. Use a stud sensor to locate the two studs, clearly marking the centers of the studs. Use a long level to make sure these marks are horizontally level.
CAUTION Read this section carefully prior to install. Step 3: Attach TV to TV Plate With the TV brackets firmly secured to the TV, use two people to lift the TV into position and hook the TV brackets onto the TV plate, as shown in Diagram D. Tighten safety bolts at the bottom of the TV brackets as shown in Diagram E.
Step 5: Tilt the TV The SA51 will tilt +14/-8° to provide the ideal viewing angle. Loosen the tilt lever on the right side by rotating it counter-clockwise from bottom to top as shown in Diagram H. (Loosen the tilt lever on the left side by rotating it counter-clockwise from top to bottom). To loosen further, flip the lever to avoid contact with the TV plate. Tilt the TV to the desired angle, then tighten the tilt levers by rotating them clockwise.
Check out more great products from Seneca AV SA21 SM61 SN21 Warranty Limited Warranty To Original Purchaser Seneca AV warrants the equipment it manufactures to be free from defects in material and workmanship for the following limited warranty period of: 24 months parts and labour.
