User's Manual

~
41
~
2.
Press
HOLD
soft key to put call on hold.
3.
Press
OPTION
soft key to enter feature list for selection.
4. Press number 2 and enter a two-digit Handset ID to call another handset
extension.
a.
Un
-
announced Call Transfer
:
Press END before the destination handset answers, the call is
automatically transferred to the destination handset.
b.
Announced Call Trans
fer
:
(1) Speak to the destination handset.
(2) Press XFER soft key or the END to end announcement. The call is transferred
to the destination handset.
Notes:
1. If the destination handset does not answer after handset paging
timeout, the call is routed back to the originating handset.
2. Above described “Call Transfer” is for DuraFon PRO handset-to handset
call transfers
.
Call Manager (Register to 1X base only)
“Call Manager” feature allows the handset to be set to receive all incoming,
transferred, and 2-Way/Intercom calls OR just transferred and 2-Way/
Intercom calls. The option is selectable by base 1 to base 4. Besides, this
feature allows you to select a specific base station to make an outgoing call.
1.
Decide whether to receive the incoming, transferred,
and 2
-
Way/Intercom
calls from a specific base station:
a. Press MENU - 8 to enter the Call Manager function.
The screen will display:
b.
Press 1 to enter “incoming” setti
ng.
c.
Use or Scrolling keys to select a base from
base 1 to base 4.
d.
Then press the

YES NO
key to switch between
Yes and No, then press SAVE key to confirm the
setting.
e.
Repeat the process until all base stations from



11

Main Menu: 
8. Call Manager
9. System



11

Call Manager: 
1. Incoming
2. Outgoing



11

Receive Calls
From base 1: 
SAVE YES NO
~
42
~
which calls are to b
e accepted have been
selected for the handset
2. Decide whether to select a specific base station to make
outgoing call:
a.
Press
MENU
-
8
to enter the Call Manager function.
b.
Press 2 to enter “Outgoing” setting.
c.
Use or to select either On or Off.
d.
Scroll to On and press
SAVE
if you want to select a
specific base station before you make an
outgoing call. The default setting is Off.
Change System Settings by Administrator (Register to 1X base only)
There are four types of system setting that can be adjusted by Administrator.
1.
Dial Mode
a.
Press
MENU
-
9
and enter the two
-
digit base ID to
enter the System mode
.
b.
Press 1 to enter Dial Mode
selection
c. You can adjust the dial mode between Tone and
Pulse.
d
.
The default s
etting is Tone.
2.
Flash
a. Press MENU-9 and enter the two-digit base ID to
enter the System mode.
b.
Press 2 to enter Flash selection
c. You can adjust the flash time from 100ms to 900 ms (9
levels to choose from.) For example, press “2” if the
desired flash time is 200ms. You will see “Done” once
you finish the setting.
d
.
The default setting is
6
00ms.
Notes:
If the
base station is adjunct to a PBX system, it is
recommended to adjust the flash time of DuraFon 1X to
match the PBX spec.
3.
Clear HS
a.
This function is useful if you want to replace a new



11

System: 
1. Dial Mode
2. Flash



11

Main Menu: 
8. Call Manager
9. System



11

Flash:
1-9 * 100msec
(600msec)
Flash(msec)
:





11

Done



11

System: 
2. Flash Time
3. Clear HS



11

Select Base
On
SAVE