802.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied.
Table of Contents CHAPTER 1: INTRODUCTION ..........................................................1 FEATURES ................................................................................................1 PHYSICAL DETAILS.....................................................................................1 CHAPTER 2: INSTALLATION.............................................................2 Install Software ................................................................................................
Chapter 1: Introduction The Dual-band Wireless USB Dongle can access two different networks which could act in any WiFi station or AP combinations. Operating either in the Hz and 5GHz frequency bands, the Dual-band Wireless USB Dongle effectively increases the available wireless bandwidth and reduces wireless interference. The Dual-band Wireless USB Dongle also supports WiFi Direct feature that can easily build a WiFi P2P PAN network. The Dual-band Wireless USB Dongle supports 802.
Chapter 2: Installation Install Software Note: Do not insert the Wireless USB Adapter into the computer until the InstallShield Wizard finished installing. 1. Exit all Windows programs. Insert the included Installation CD into the computer. The CD-ROM will run automatically. Please click Next to process the installation. 2.When the following screen appears, click Finish to restart the computer to complete the software installation.
Chapter 3: Network Connection How to Make a Connection To make a connection with an access point, please follow below steps. Here takes Windows XP OS for example. Step 1: After set up the Wireless USB Adapter successfully, please launch the Configuration Utility. There are two ways to launch the utility by: (1) Double clicking the Intelligent Wireless LAN Utility icon on the desktop. (2) Or go to Start All Programs Intelligent Wireless LAN Utility Intelligent Wireless LAN Utility.
Chapter 4: Utility Configuration Station Mode Show Tray Icon: Check to show the wireless adapter icon at the tray. Disable Adapter: Check this to disable the wireless adapter. Radio off: Check this to turn OFF radio function. Windows Zero Config: Click to use windows built-in wireless utility. Close: Click to leave the Intelligent Wireless LAN Utility. General The General page displays the detail information of current connection. General Tab Status Shows the current connected status.
Profile Tab Profile Name Here shows a distinctive name of profile in this column. SSID The SSID is the unique name shared among all wireless access points in the wireless network. Add Click Add button to add a profile from the drop-down screen. Profile Name: Users can enter profile name at will. Network Name (SSID): The SSID is the unique network name (case-sensitive) shared among all wireless access points in the wireless network.
mutual authentication of the client and the network. It relies on client-side and server-side certificates to perform authentication and can be used to dynamically generate user-based and session-based WEP keys to secure subsequent communications between the WLAN client and the access point. LEAP: Light Extensible Authentication Protocol. It is an EAP authentication type used primarily in Cisco Aironet WLANs.
Channel Shows the currently channel in use. Encryption Shows the encryption type currently in use. Valid value includes WEP, TKIP, AES, None and TKIP/AES. Network Authentication Show the device network authentication. Signal Shows transmit power, the amount of power used by a radio transceiver to send the signal out. Type Network type in use, Infrastructure or Ad-Hoc mode. BSSID Shows Wireless MAC address. Supported Rate(s) Shows the transmitting data rate. Mode Supported wireless mode.
WPS The primary goal of Wi-Fi Protected Setup (Wi-Fi Simple Configuration) is to simplify the security setup and management of Wi-Fi networks. The STA as an Enrollee or external Registrar supports the configuration setup using PIN (Personal Identification Number) configuration method or PBC (Push Button Configuration) method through an internal or external Registrar. WPS Tab PIN Code 8-digit numbers. It is required to enter PIN Code into Registrar when using PIN method.
point. Channel: User can select the channel form the pull-down list. Wireless network security Network Authentication: There are several types of authentication modes including Open System, Shared Key, WPA-PSK and WPA2-PSK. Data encryption: For Open System and Shared Key authentication mode, the selection of encryption type is WEP. For WPA-PSK, WPA2-PSK, authentication mode, the encryption type supports both TKIP and AES. When encryption is set to WEP… ASCII: Only valid when using WEP encryption algorithm.
Rx Retry Shows information of packets failed transmit after hitting retry limit. Rx ICV Error Shows information of packets received with ICV error. Reset Click to reset counters to zero. ICS This page displays setting Internet connection sharing (ICS). Select a sharing public network and click Apply button to make a connection. Chapter 5: Remove To remove the utility and driver, please refer to below steps. (When removing the utility, the driver will be removed as well.) 1.
