User's Manual
Table Of Contents
- Contents
- Chapter 1: Regulatory Compliance Statements
- Federal Communications Commission (FCC) Compliance Notices
- Class B Interference Statement
- FCC Caution
- RF Radiation Exposure and Hazard Statement
- Non-Modification Statement
- Deployment Statement
- Outdoor operating restrictions
- Dynamic Frequency Selection (DFS) in the 5.0 GHz UNII bands
- Canadian IC Statements
- European Union and European Free Trade Association (EFTA) Regulatory Compliance
- Declaration of Conformity
- European Community Declaration of Conformity
- Countries of Operation and Restrictions of Use in the European Community
- Operation Using the 2.400 to 2.4835 GHz Channels in the European Community
- Operation Using the 5.15 to 5.25 GHz, 5.25 to 5.35 GHz, and 5.470 to 5.725 GHz Channels in the European Community
- Russia, Belarus, and Kazakhstan Requirement
- Antenna Statement
- Chapter 2: Devices with detachable antennas
- Chapter 3: English
- Kapitel 4: Deutsch
- Einführung
- Sicherheitsmaßnahmen
- Installation des WLAN-AP 8120-O
- Hardware
- Kabelanschlüsse
- Abdichten des Ethernet-UTP-Kabels
- Mounten eines WLAN-AP 8120-O an einem vertikalen Mast
- Mounten eines WLAN-AP 8120-O an einem horizontalen Mast
- Mounten eines WLAN-AP 8120-O an einer Wand
- Installation des Ethernet-Überspannungsableiters
- Installation des Power over Ethernet-Injektors
- Sicherheitshinweise
- Capítulo 5: Español
- Introducción
- Precauciones de seguridad
- Instalación del WLAN AP 8120-O
- Hardware
- Requisitos de cableado
- Impermeabilización del cable UTP Ethernet
- Instalación del WLAN AP 8120-O en un poste vertical
- Montaje del WLAN AP 8120-O en un poste horizontal
- Instalación del WLAN AP 8120-O en una pared
- Instalación del disipador de sobretensiones Ethernet
- Instalación del inyector Power over Ethernet
- Advertencias de seguridad
- Chapitre 6 : Français
- Capítulo 7: Português do Brasil
Installation des WLAN-AP 8120-O
In diesem Abschnitt werden die folgenden Verfahren beschrieben:
• Mounten eines WLAN-AP 8120-O an einem vertikalen Mast
•
Mounten eines WLAN-AP 8120-O an einem horizontalen Mast
• Mounten eines WLAN-AP 8120-O an einer Wand
• Installation eines Ethernet-Überspannungsableiters
• Abdichten eines Ethernet-Steckers für die Verwendung im Freien
• Installation eines PoE-Injektors (Power over Ethernet)
Hardware
Das Installationspaket enthält die folgenden Teile:
• 1 Access Point
Avaya WLAN-AP 8120-O
• 1 Montageset:
- 1 Flachhalterung
- 2 Basishalterungen
- 1 Schlauchschelle
- 4 Ankerbolzen
- 4 Halbrundschrauben
- 8 Sechskantschrauben
• 1 Ethernet-Überspannungsableiter
• 1 Dichtung zum Abdichten der Ethernet-Verbindung am Access Point
• 2 2,4-GHz-Antennen
• 2 5-GHz-Antennen
Anforderungen bezüglich Wärme- und Kältebelastung
Die Betriebstemperatur des WLAN 8100-AP 8120-O muss zwischen -40 und +60 °C liegen.
Kabelanschlüsse
Vor dem Anschließen des
AP 8120-O über ein Ethernet-UTP-Kabel müssen Sie sicherstellen,
dass das Kabel ordnungsgemäß abgedichtet ist, damit es im Freien verwendet werden kann.
Deutsch
52 Avaya WLAN 8100 Regulatory Information — WLAN AP 8120-O February 2012
Kommentare? infodev@avaya.com