User's Manual
Table Of Contents
- Contents
- Chapter 1: Regulatory Compliance Statements
- Federal Communications Commission (FCC) Compliance Notices
- Class B Interference Statement
- FCC Caution
- RF Radiation Exposure and Hazard Statement
- Non-Modification Statement
- Deployment Statement
- Outdoor operating restrictions
- Dynamic Frequency Selection (DFS) in the 5.0 GHz UNII bands
- Canadian IC Statements
- European Union and European Free Trade Association (EFTA) Regulatory Compliance
- Declaration of Conformity
- European Community Declaration of Conformity
- Countries of Operation and Restrictions of Use in the European Community
- Operation Using the 2.400 to 2.4835 GHz Channels in the European Community
- Operation Using the 5.15 to 5.25 GHz, 5.25 to 5.35 GHz, and 5.470 to 5.725 GHz Channels in the European Community
- Russia, Belarus, and Kazakhstan Requirement
- Antenna Statement
- Chapter 2: Devices with detachable antennas
- Chapter 3: English
- Kapitel 4: Deutsch
- Einführung
- Sicherheitsmaßnahmen
- Installation des WLAN-AP 8120-O
- Hardware
- Kabelanschlüsse
- Abdichten des Ethernet-UTP-Kabels
- Mounten eines WLAN-AP 8120-O an einem vertikalen Mast
- Mounten eines WLAN-AP 8120-O an einem horizontalen Mast
- Mounten eines WLAN-AP 8120-O an einer Wand
- Installation des Ethernet-Überspannungsableiters
- Installation des Power over Ethernet-Injektors
- Sicherheitshinweise
- Capítulo 5: Español
- Introducción
- Precauciones de seguridad
- Instalación del WLAN AP 8120-O
- Hardware
- Requisitos de cableado
- Impermeabilización del cable UTP Ethernet
- Instalación del WLAN AP 8120-O en un poste vertical
- Montaje del WLAN AP 8120-O en un poste horizontal
- Instalación del WLAN AP 8120-O en una pared
- Instalación del disipador de sobretensiones Ethernet
- Instalación del inyector Power over Ethernet
- Advertencias de seguridad
- Chapitre 6 : Français
- Capítulo 7: Português do Brasil
Chapter 3: English
About this task
Using the following procedures and information when installing the Avaya WLAN AP 8120-O.
Introduction
This section describes site conditions required before installing the WLAN AP 8120-O access
point.
Site Planning
Perform a visual inspection
to determine and document the physical characteristics of the site.
Ensure that the site planning meets the following requirements before you begin the
installation:
• Identify the roof area, wall, or tower for mounting the WLAN AP 8120-O.
• Choose a site with a clear line-of-sight from the transmitting antenna.
• Determine the access area, such as a stairway or a ladder.
• Identify existing equipment installations and assess the condition of proposed towers or
mounting structures.
• Assess environmental conditions, such as temperature, ventilation, and humidity.
Ethernet
The WLAN AP 8120-O must be closer than 100 meters from the Power over Ethernet (PoE).
Note:
Avaya recommends that you use outdoor CAT5E Ethernet cable for all external
connections.
Antenna
The WLAN AP 8120-O uses two 5.0 GHz and two 2.4 GHz antennas.
Caution:
Only use Avaya approved antennas with the WLAN AP 8120-O.
A WLAN AP 8120-O that
is outfitted with non-certified Avaya antennas is not supported under Avaya support
agreements.
Avaya WLAN 8100 Regulatory Information — WLAN AP 8120-O February 2012 19