User's Manual
Table Of Contents
- Contents
- Chapter 1: Regulatory Compliance Statements
- Federal Communications Commission (FCC) Compliance Notices
- Class B Interference Statement
- FCC Caution
- RF Radiation Exposure and Hazard Statement
- Non-Modification Statement
- Deployment Statement
- Outdoor operating restrictions
- Dynamic Frequency Selection (DFS) in the 5.0 GHz UNII bands
- Canadian IC Statements
- European Union and European Free Trade Association (EFTA) Regulatory Compliance
- Declaration of Conformity
- European Community Declaration of Conformity
- Countries of Operation and Restrictions of Use in the European Community
- Operation Using the 2.400 to 2.4835 GHz Channels in the European Community
- Operation Using the 5.15 to 5.25 GHz, 5.25 to 5.35 GHz, and 5.470 to 5.725 GHz Channels in the European Community
- Russia, Belarus, and Kazakhstan Requirement
- Antenna Statement
- Chapter 2: Devices with detachable antennas
- Chapter 3: English
- Kapitel 4: Deutsch
- Einführung
- Sicherheitsmaßnahmen
- Installation des WLAN-AP 8120-O
- Hardware
- Kabelanschlüsse
- Abdichten des Ethernet-UTP-Kabels
- Mounten eines WLAN-AP 8120-O an einem vertikalen Mast
- Mounten eines WLAN-AP 8120-O an einem horizontalen Mast
- Mounten eines WLAN-AP 8120-O an einer Wand
- Installation des Ethernet-Überspannungsableiters
- Installation des Power over Ethernet-Injektors
- Sicherheitshinweise
- Capítulo 5: Español
- Introducción
- Precauciones de seguridad
- Instalación del WLAN AP 8120-O
- Hardware
- Requisitos de cableado
- Impermeabilización del cable UTP Ethernet
- Instalación del WLAN AP 8120-O en un poste vertical
- Montaje del WLAN AP 8120-O en un poste horizontal
- Instalación del WLAN AP 8120-O en una pared
- Instalación del disipador de sobretensiones Ethernet
- Instalación del inyector Power over Ethernet
- Advertencias de seguridad
- Chapitre 6 : Français
- Capítulo 7: Português do Brasil
10. L'AP 8120-O WLAN est alimenté par un périphérique PoE (Power over Ethernet).
Choisissez l'une des options suivantes pour connecter à l'AP 8120-O WLAN un
parasurtenseur Ethernet et un injecteur PoE.
Remarque :
Si vous utilisez l'injecteur PoE d'Avaya, vous n'avez pas besoin d'utiliser le
parasurtenseur Ethernet fourni car l'injecteur assure la protection contre les
surtensions.
a. Pour connecter le parasurtenseur Ethernet fourni à l'AP 8120-O WLAN,
reportez-vous à la section Installation d'un parasurtenseur Ethernet à la
page 122.
b. Pour connecter l'injecteur PoE d'Avaya à l'AP 8120-O WLAN, reportez-vous à
la section Installation de l'injecteur PoE à la page 126.
Installation de l'AP 8120-O WLAN sur un tuyau horizontal
Pourquoi et quand exécuter cette tâche
Pour installer l'AP
8120-O WLAN sur un tuyau horizontal, procédez comme suit.
Procédure
1.
Placez les rondelles freins et plates sur les quatre vis d'assemblage à tête
hexagonale.
Illustration 80 : Fixation du support plat à l'arrière du boîtier
2. Serrez les vis afin de fixer le support plat à l'arrière du boîtier.
Installation de l'AP 8120-O WLAN
Avaya WLAN 8100 Regulatory Information — WLAN AP 8120-O February 2012 115