SMH10R Low Profile Motorcycle Bluetooth® Headset & Intercom 900m Intercom 980yds Ultra Slim & Feather Light www.senabluetooth.
SMH10R Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. SMH10™, SMH5™, SPH10™, SPH10S™, SPH10H™, SR10™, SM10™, SMH5-FM™, SMH10R™ are trademarks of Sena Technologies, Inc. or its subsidiaries. These trademarks may not be used without the express permission of Sena. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license. iPhone, iPod touch are registered trademarks of Apple Inc.
SMH10R CONTENTS 1. 2. 3. 4. INTRODUCTION PACKAGE CONTENTS INSTALLING THE SMH10R ON YOUR HELMET POWERING ON/OFF AND CHARGING 4.1 4.2 4.3 4.4 4.5 Powering On Powering Off Charging Low Battery Warning Checking the Battery Level 5. VOLUME ADJUSTMENT 6. SMH10R CONFIGURATION SETTING 6.1 Mobile Phone Pairing 6.2 Multipoint Pairing 6.3 Phone Selective Pairing 6.4 Media Selective Pairing 6.5 Enabling/Disabling Voice Activated Phone Answering 6.6 Enabling/Disabling Voice Activated Intercom 6.
SMH10R Thank you for choosing the Sena SMH10R, Low Profile Bluetooth Stereo Headset and Intercom. With the SMH10R, you can call handsfree on your Bluetooth mobile phone, listen to stereo music or voice instructions from your GPS navigation system by wireless Bluetooth, and have intercom conversations in full duplex with a passenger or other motorcycle riders. The SMH10R is compliant with the Bluetooth 3.
SMH10R 2.
SMH10R • Double Sided Adhesive Tapes for Main Unit • Microphone Sponges 3. INSTALLING THE SMH10R ON YOUR HELMET English • Velcro Pads for Main Unit To securely install the main unit of the SMH10R, you can use the velcro pad or double sided adhesive tape. Please follow the procedure below. 1. Peel off the cover of the adhesive tape of the velcro pad and attach it on the back plate of the main unit. • USB Power & Data Cable • Cigarette Charger 2.
SMH10R 4. Attach the main unit to the velcro pad of your helmet. 5. Place the speakers to the helmet along with the velcro pads, centered to your ear, in the ear pockets of the helmet. If the helmet has deep ear pockets, you can use the speaker pads to place the speakers closer to your ears. Attach the speaker connector to the 4 pin connector of the main unit cable. 6. There are two types of microphones that can be installed in your helmet.
SMH10R 4. POWERING ON/OFF AND CHARGING English 7. Attach the velcro pads to the battery pack in the same manner as the main unit and place the battery on the back side of your helmet. Attach the battery connector to the 2 pin connector of the main unit cable. 4.1 Powering On Press the Center Button and the (+) Button at the same time for 1 second to power on. The blue LED turns on and you will hear ascending beeps and “Hello”. 4.
SMH10R prompt, “Low battery”. 4.5 Checking the Battery Level You can check the battery level in two different ways when the headset is powering on. 4.5.1 LED Indicator When the headset is powering on, the red LED flashes rapidly indicating the battery level. 4 flashes = High, 70~100% 3 flashes = Medium, 30~70% 2 flashes = Low, 0~30% 4.5.
SMH10R You can set the configuration of the SMH10R by the voice menu instruction as below. 1. To enter into voice configuration menu, press and hold the Center Button for 10 seconds until the LED shows solid blue and you hear high tone double beeps. You will also hear a voice prompt, “Configuration menu”. 2. Tap the (+) Button or (-) Button to navigate between the menus. You will hear voice prompts for each menu items as below. 3.
SMH10R 6.1 Mobile Phone Pairing Voice Prompt “Phone pairing” Factory Default N/A To go into mobile phone pairing mode, tap the (+) Button or the (-) Button until you hear a voice prompt, “Phone pairing”. Please refer to section 7.1 for details on mobile phone pairing. If you tap the (+) or (-) Button, you can exit from the phone pairing mode. 6.
SMH10R 6.6 Enabling/Disabling Voice Activated Intercom Voice Prompt “VOX intercom” Factory Default Disable Enable / Disable Tap the Center Button Tap the (+) Button or the (-) Button until you hear a voice prompt, “VOX intercom”. If this feature is enabled, you can initiate an intercom conversation with the last connected intercom friend by speaking any word loudly enough.
SMH10R 6.9 Delete All Bluetooth Pairing Information Voice Prompt “Delete all pairings” Voice Prompt “Exit configuration” Factory Default N/A Factory Default N/A Enable / Disable Tap the Center Button Execute Tap the Center Button To delete all Bluetooth pairing information on the SMH10R, tap the (+) Button or the (-) Button until you hear a voice prompt, “Delete all pairings”. Tap the Center Button to confirm. 6.
SMH10R Tap Center Button Phone Pairing None Multipoint Pairing None Phone Selective Pairing None Media Selective Pairing None VOX Phone Enable / disable VOX Intercom Enable / disable VOX Sensitivity - Set up 1 /2 / 3 / 4 / 5 or cancel - Enter adjustment mode - Save and exit Voice prompt Enable / disable Delete All Pairings Execute Factory Reset Execute Exit Configuration Execute Voice Configuration Menu & Button Operations 7.
SMH10R Sena SMH10R in the list of the devices detected on the mobile phone. 4. Enter 0000 for the PIN. Some mobile phones may not ask for the PIN. 5. The mobile phone confirms that pairing has completed and the SMH10R is ready to use. You will hear a voice prompt, “Your headset is paired”. 6. If the pairing process is not completed within three minutes, the SMH10R will return to stand-by mode. 7.
SMH10R 1. I f a Bluetooth connection between the headset and a mobile phone is disconnected, press the Center Button for 3 seconds until you hear a high tone single beep to recover the Bluetooth connection immediately. 2. If a Bluetooth connection between the headset and a media player is disconnected, press the Center Button for 1 second to recover the Bluetooth connection and play. 7.4 Bluetooth GPS Navigation Pairing You can listen to voice instruction from Bluetooth GPS navigation.
SMH10R The pairing diagram for multipoint GPS pairing is shown in the figure below. Smart Phone 7.4.2 GPS Pairing as Mobile Phone If GPS is not only used for turn-by-turn voice instructions but also is your preferred Bluetooth stereo music source, you can pair the GPS to the SMH10R by following the simple procedures in “7.1 Mobile Phone Pairing”. When you do this, the SMH10R thinks the GPS is a mobile phone. But SMH10R can directly pair an additional mobile phone.
SMH10R The Sena SR10 is a Bluetooth two-way radio adapter for group communication, and uses HFP as do most motorcycle specific GPS navigation systems. If you pair the SMH10R with a SR10 by multipoint pairing, the SMH10R is able to have two HFP devices at the same time: mobile phone and Sena SR10. 1. To enter into the voice configuration menu, press and hold the Center Button for 10 seconds until you hear a voice prompt, “Configuration menu”. 2.
SMH10R 8. PAIRING WITH SELECTIVE PROFILE: HFP OR A2DP STEREO If you have a MP3 stereo music phone such as a smartphone, sometimes you may need to selectively use the SMH10R for A2DP stereo music only or for mobile phone handsfree only. This instruction is for advanced users who want to pair the SMH10R to their smartphones only with one selective profile: A2DP stereo for music or HFP for phone call.
SMH10R 9.1 Pairing with Other SMH10R Headsets for Intercom Conversation The SMH10R can be paired with up to three other headsets for Bluetooth intercom conversation. 1. Turn on the two SMH10R headsets (A and B) that you would like to pair with each other. 2. Press and hold the Center Button for 5 seconds, then you will hear a mid-tone single beep and a voice prompt, “Intercom pairing”. 3. Simply tap the Center Button of any one of the two headsets A or B (It doesn’t matter that you choose A or B.
SMH10R 5. The intercom pairing queue is ‘Last-Come, First-Served’. If a headset has multiple paired headsets for intercom conversations, the last paired headset is set as first intercom friend. The previous intercom friend becomes second intercom friend, and third intercom friend. Note: For example, after the pairing procedures listed above, headset D is the first intercom friend of headset A. Headset C is the second intercom friend of headset A, and headset B is the third intercom friend of headset A. 9.
SMH10R You can listen to stereo music from your Bluetooth wireless audio device. The Bluetooth audio device must be paired with the SMH10R by following the “Bluetooth Stereo Device Pairing” procedures described in the 7.3 chapter. The SMH10R supports the Audio/Video Remote Control Profile (AVRCP), so if your Bluetooth audio device also supports the AVRCP, you can use the SMH10R to remotely control music playback.
SMH10R 12. MOBILE PHONE CALL MAKING AND ANSWERING redial”. - To cancel the voice dialing or redialing last number command, tap the Center Button while it is in progress. Answer 1. When you have an incoming call, tap the Center Button to answer the call. 2. You can also answer the incoming call by loudly speaking any word of your choice if Voice Activated Phone Answering is enabled, unless you are connected to intercom. 3.
SMH10R English 13. TWO-WAY INTERCOM Terminate 13.1 Start and End Two-way Intercom 1. You can start a one-on-one intercom conversation with any intercom friend by tapping the Center Button: Single tapping to intercom with the first intercom friend, double tapping with the second intercom friend, or triple tapping with the third intercom friend.
SMH10R 13.3 Intercom and Mobile Phone Call 1. When you have an incoming mobile phone call during an intercom conversation, you will hear a ring tone. You can choose whether to 1) answer the mobile phone call and stop the intercom conversation, or 2) reject the phone call and stay on the intercom conversation or 3) Ignore the incoming phone call and allow the caller to go to voice mail. a. To answer the phone call and stop the intercom conversation, tap the Center Button.
SMH10R English 13.5 Intercom and Two-way Radio As described in 6.4 of this user's guide, you can use a two-way radio and SMH10R Bluetooth intercom simultaneously by using the Sena SR10, a Bluetooth Two-way Radio Adapter, along with the SMH10R. Incoming audio from the two-way radio is not interrupting an intercom conversation but is heard in background.
SMH10R 14. THREE-WAY CONFERENCE INTERCOM 14.1 Start Three-way Intercom You (A) can have a three-way conference intercom with two other SMH10R friends (B & C) by establishing two intercom connections at the same time. While a three-way conference intercom is in progress, mobile phone connection of all three participants would be temporarily disconnected, but as soon as the conference intercom terminates or one of the participants leaves the intercom, all mobile phones would be automatically reconnected.
SMH10R Press for 1” (A) Single tap Double tap First Friend (B) Second Friend (C) Result English Center Button Disconnect (B) & (C) Disconnect (B) Disconnect (C) End Three-way Intercom 14.2 End Three-way Intercom When you are a member of an active three-way conference intercom, you can completely terminate the conference intercom or just disconnect an intercom connection with one of your active intercom friends. 1.
SMH10R 15. FOUR-WAY CONFERENCE INTERCOM 15.1 Start Four-way Intercom You can have four-way conference intercom with three other SMH10R users by adding one more intercom participant to the three-way intercom. While you are having three-way intercom as above in section 14.1, a new participant (D), who is an intercom friend of your intercom friend (C), may join the conference intercom by making an intercom call to your intercom friend (C).
SMH10R You can have a three-way conference phone call by adding an intercom friend to the mobile phone conversation. While having a mobile phone call, make an intercom call to one of your intercom friends (B, C or D) by tapping the Center Button once, twice or three times to form a three-way conference call with the person on the mobile phone line. To disconnect the intercom first and go back to your private mobile phone call, terminate the intercom by tapping the Center Button once.
SMH10R 19. RESET TO FACTORY DEFAULT SETTINGS When the SMH10R is not working properly or is in faulty status for any reason, you may reset by pushing the pin-hole reset button at the back of the headset main unit. Insert a paper clip into the reset pin-hole and press the reset button for a second with light pressure. The SMH10R will be switched off, and you have to turn the system back on and try again. However, this will not restore the headset to factory default settings. 21.
SMH10R Case 3 •iPhone for mobile phone call and stereo music streaming •ZumoTM 660/665 for GPS voice instruction •SMH10R for two-way intercom •iPhone for mobile phone call via Zumo 660/665 • Zumo 660/665 for GPS voice instruction and stereo music streaming •SMH10R for two-way intercom Pairing: Refer to ZumoTM 660/665 manual Mobile Call iPhone Mobile Call Pairing: 7.1 Music ZumoTM 660/665 iPhone Mobile Call Music Pairing: 7.1 GPS Voice Intercom Conversation SMH10R Pairing: 9.
SMH10R Case 4 Case 5 •Feature phone for mobile phone call •iPod Touch for stereo music streaming •Two other SMH10R for three-way conference intercom •iPhone for mobile phone call •iPod Touch for stereo music streaming •TomTom® Rider2 for GPS voice instruction •SMH10R for two-way intercom Feature Phone iPhone Mobile Call Intercom Conversation SMH10R Pairing: 9.1 Pairing: 7.1 Mobile Call Music SMH10R Pairing: 7.3 Intercom Pairing: 9.1 Conversation Pairing: 8.
SMH10R Case 6 iPhone Mobile Call Music Wired Connection Tow-way radio GPS Voice Alarm SMH10R Pairing: 7.5 Intercom Conversation Pairing: 9.1 SMH10R Wired Connection Sena SR10* Wired Connection Radar Detector The SMH10R has an external, rechargeable battery. The battery can be charged and discharged hundreds of times, but it will eventually wear out. Recharge the battery only with Sena approved chargers designated for this device.
SMH10R MAINTENANCE AND CARE DISPOSAL The SHM10R should be treated with care and the following suggestions will help you protect your warranty coverage. 1. Do not use or store the device in dusty, dirty areas. Its moving parts and electronic components can be damaged. 2. Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and wrap or melt certain plastics. 3. Do not store the device in cold areas.
SMH10R FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. •T his device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
SMH10R Please note that this product uses radio frequency bands not harmonized within EU. Within the EU this product is intended to be used in Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal, Spain, Sweden, United Kingdom and within EFTA in Iceland, Norway and Switzerland. Industry Canada Statement This device complies with Industry Canada license-exempt RSS standard(s).
SMH10R Sena hereby notifies you that using this Device may also be in contravention to local, federal, state or national laws or regulations, and that any use of the Device is entirely at your sole risk and responsibility. 1.
SMH10R negligence or other conduct of others, including the Company. 5. You confirm that you have read this release of liability and fully understand its terms and that you have given up substantial rights by not returning the Device for a full refund (see refund option below). Two-Year Limited Warranty Sena Technologies, Inc.
SMH10R Return for Full Refund IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDITIONS, YOU MAY RETURN THIS DEVICE TO SENA FOR A FULL REFUND, PROVIDED THAT YOU DO SO NO LATER THAN 14 BUSINESS DAYS FOLLOWING THE PURCHASE OF THE DEVICE AND SUBJECT TO THE WRAPPING BEING INTACT. WHEN DOING SO, PLEASE REFER TO THIS SECTION.
1.0.0 www.senabluetooth.com User's Guide for Firmware v4.
