User's Guide www.senabluetooth.
Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. SMH10™, SMH5™, SPH10™, SPH10S™, SPH10H™, SR10™, SM10™ are trademarks of Sena Technologies, Inc. or its subsidiaries. These trademarks may not be used without the express permission of Sena. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license. Other trademarks and tradenames are those of their respective owners.
CONTENTS 1. INTRODUCTION 4 2. PACKAGE CONTENTS 7 3. INSTALLING THE SR10 9 3.1 Installing on the Handle Bar 3.2 Placing on the Belt / Pocket 4. POWERING ON/OFF AND CHARGING 9 9 10 4.1 Powering On 10 4.2 Powering Off 10 4.3 Charging 10 4.4 Low Battery Warning 10 5. PAIRING THE SR10 WITH BLUETOOTH DEVICES 12 5.1 Bluetooth Headset Pairing 12 5.2 Bluetooth Mobile Phone Pairing 12 6. USING THE SR10 13 6.1 Using Two-way Radios 13 6.2 Installing Wired PTT Button 13 6.
English 6.7 Fault Reset 17 6.8. Firmware Upgrade 17 7.
1. INTRODUCTION Thank you for choosing the Sena SR10. The SR10 is a Bluetooth two-way radio adapter and mobile phone handsfree gateway based on Bluetooth 2.1+EDR technology. Users can connect various two-way radios in the market with the SR10 and connect wirelessly to a variety of Bluetooth communication headsets. At the same time, as a Bluetooth mobile phone handsfree gateway, the SR10 lets users connect Bluetooth headsets to mobile phones as well.
English communications. Please read this user’s guide carefully before using the SR10. Also refer to www.senabluetooth.com for the latest version of the user’s guide and additional information related to Sena Bluetooth products.
Technical Specifications: • Bluetooth 2.1+EDR • Supporting profiles: Headset Profile, Hands-Free Profile (HFP) • Operating time: 12 hours • Standby time: 10 days • Battery charging time: 3.5 hours • Lithium polymer battery • Dimensions: 108 mm × 52 mm × 29 mm (4.3 in × 2.0 in × 1.1 in) • Weight: 81g (2.
English 2. PACKAGE CONTENTS • Main Unit Pairing Button • Bluetooth Headset Pairing Mode • Mobile Phone Pairing Mode PTT Button • Transmit Radio • Open Audio Channel DC Power Charging & Firmware Upgrade Port AUX2 Port • Mobile Phone, GPS Navigation, Radar/Laser Detector Main Port • 6-pin Hirose Connector for Two-way Radio Devices AUX1 Port • GPS Navigation or Radar/Laser Detector 2.
• DC Power Charger • USB Power & Data Cable • 3.
English 3. INSTALLING THE SR10 3.1 Installing on the Handle Bar 1. Place the rubber on the back of the main unit. 2. Put the joint pad on top of the rubber, and tighten the screw. 3. Place the main unit on the handle bar, wind the rubber band, and hang it on the hook. 3.2 Placing on the Belt / Pocket 1. Place the belt-clip on the back of the main unit, and tighten the screw. 2. Place the main unit on the belt with belt-clip.
4. POWERING ON/OFF AND CHARGING To power on and off the adapter, you don’t need to press and hold any button for several seconds. Just short press the Pairing Button and the PTT Button simultaneously, and you will get quick on-andoff convenience. 4.1 Powering On Press and hold the Pairing Button and the PTT Button at the same time for about 1 second to turn the power on. When the power is on, the blue LED light turns on. 4.
English 4.4 Low Battery Warning When the battery is running low, the red LED light will flash.
5. PAIRING THE SR10 WITH BLUETOOTH DEVICES 5.1 Bluetooth Headset Pairing 1. Turn on your Bluetooth headset and enter pairing mode, following the Bluetooth headset manual. 2. Turn on the SR10 and press and hold the Pairing Button for 5 seconds until the LED flashes red and blue alternatively. 3. When the pairing is successful, the blue LED flashes slowly. 5.2 Bluetooth Mobile Phone Pairing 1. Turn on the SR10 and press and hold the Pairing Button for 8 seconds until the red LED is rapidly flashing.
English 6. USING THE SR10 6.1 Using Two-way Radios 1. When SR10 is turned on and connected with a hand held twoway radio, the audio from the two-way radio will be directly sent to your Bluetooth headset. You can use the Bluetooth headset as a handsfree device for the two-way radio. 2. To talk using the two-way radio through SR10, press and hold the PTT Button until you finish talking. 6.2 Installing Wired PTT Button 1.
6.3 Ports and Cables The SR10 has one Main Port and two AUX ports for wired connection with other devices. Below is a list of compatible cables and devices: • Main: 6-pin Hirose connector type two-way radio cable * • AUX1: 3.5mm 3-pole audio jack cable for GPS, radar detectors or laser detectors ** • AUX2: 3.5mm 3-pole audio jack cable for GPS, radar detectors or laser detectors, or 3.
6.4 Using Mobile Phone 6.4.2 For Wired Connection Users can connect a mobile phone to the AUX2 Port by wire in order to use Bluetooth handsfree. In this case, the SR10 combines audio from the Main Port and the AUX2 Port together and redirects to the Bluetooth headset. For information on mobile phones and cable compatibility, please visit www. senabluetooth.com/support. 6.
sound from the wired devices for a certain period of time, the SR10 disconnects itself from the Bluetooth headset. Even if there is no incoming sound from the wired devices, users can also connect the SR10 manually to the Bluetooth headset by double tapping the PTT Button. Users can also double tap the PTT Button while the SR10 is already connected to the Bluetooth headset to prevent it from disconnecting itself automatically.
6.7 Fault Reset If the SR10 is not working properly or is in a faulty status for any reason, you may reset by pushing the small reset button at the top of the SR10 main unit. By using a paper clip or a pencil tip, lightly press and hold the reset button for 1 second. The SR10 will be switched off. Turn the SR10 back on to use it. However, this will not restore the SR10 to factory default settings. 6.8 Firmware Upgrade The SR10 supports firmware upgrade function. Please visit Sena Bluetooth web site at www.
7.
English BATTERY INFORMATION The SR10 has an internal, non-removable, rechargeable battery. Do not attempt to remove the battery from the device as you may damage the device. The battery can be charged and discharged hundreds of times, but it will eventually wear out. Recharge the battery only with Sena approved chargers designated for this device. Use of an unapproved charger may present a risk of fire, explosion, leakage, or other hazard.
MAINTENANCE AND CARE The SR10 should be treated with care and the following suggestions will help you protect your warranty coverage. 1. Do not use or store the device in dusty, dirty areas. Its moving parts and electronic components can be damaged. 2. Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and wrap or melt certain plastics. 3. Do not store the device in cold areas.
English DISPOSAL The crossed-out wheel bin symbol on the product, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies to the European Union and other locations where separate collection systems are available.
CERTIFICATION AND SAFETY APPROVALS • FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: - This device may not cause harmful interference, and - This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
- Consult the dealer or an experienced radio/TV technician for help. • FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. The antenna used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures.
product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. For further information please consult http://www.senabluetooth.com. Please note that this product uses radio frequency bands not harmonized within EU.
25 English all interoperability tests that are specified in the Bluetooth® specification. However, interoperability between the device and other Bluetooth® -enabled products is not guaranteed.
WAIVER AND GENERAL RELEASE By using the SR10, you waive any legal rights including the right to sue. Please read the following carefully before using the device. If you do not accept all terms of this agreement, you should immediately return the product for a full refund. By using the SR10, you agree to be bound to this agreement and forfeit the right to sue.
actively involved in traffic. from any liability, loss, claim and expense (including attorneys fees) and holding Sena harmless for any bodily injuries, harm or death as well as losses or damages in goods, to any Vehicles including your own, or to any property or asset that belong to you or to third parties, any of which may result from using the Device under any circumstances or conditions and irrespective of jurisdiction.
debts, demands, actions and liability which may arise, directly or indirectly, from using the Device for any distress, pain, suffering, discomfort, loss, injury, death, damages to or in respect to any person or property however caused, WHETHER ARISING FROM THE NEGLIGENCE OR OTHERWISE, and which may hereafter accrue to you on some future date as a result of said use, to the fullest extent permitted by law. 2.
whether caused in whole or in part by the negligence or other conduct of others, including the Company. 5. You confirm that you have read this release of liability and fully understand its terms and that you have given up substantial rights by not returning the Device for a full refund (see refund option below). • Two-Year Limited Warranty Sena Technologies, Inc.
specified functions, or any other non- conformance caused by or attributable to: (a) any misapplication or misuse of the Product; (b) failure of Customer to adhere to any of Sena’s specifications or instructions; (c) neglect of, abuse of, or accident to, the Product; or (d) any associated or complementary equipment or software not furnished by Sena.
PARTS OR SERVICES HEREUNDER OR THE PERFORMANCE, USE OR INABILITY TO USE THE SAME, EVEN IF Sena OR ITS DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL Sena OR ITS DEALERS TOTAL LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT.
WARNING Sena informs that using this device in public traffic may not be authorized by the law. Please check your local law and use this device only out of public traffic such as private properties or closed circuits. Sena denies any liability should you choose not to respect this warning.
1.1.1 User's Guide for Firmware v1.2 www.senabluetooth.
