www.senabluetooth.
SPH10 Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. SMH10™, SMH5™, SPH10™, SPH10S™, SPH10H™, SR10™, SM10™ are trademarks of Sena Technologies, Inc. or its subsidiaries. These trademarks may not be used without the express permission of Sena. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license. iPhone, iPod touch are registered trademarks of Apple Inc.
SPH10 CONTENTS 1. INTRODUCTION 2. PACKAGE CONTENTS 3. WEARING THE SPH10 3.1 Microphone Installation 3.2 Placing the Headset on Your Ear 4. POWERING ON/OFF AND CHARGING 4.1 Powering On 4.2 Powering Off 4.3 Charging 4.4 Low Battery Warning 4.5 Checking the Battery Level 5. VOLUME ADJUSTMENT 6. PAIRING THE SPH10 WITH BLUETOOTH DEVICES 6.1 Mobile Phone Pairing 6.2 Bluetooth Stereo Device Pairing 6.3 Bluetooth GPS Navigation Pairing 6.4 Pairing with the SENA SR10, Bluetooth Two-way Radio Adapter 7.
SPH10 Thank you for choosing the Sena SPH10, Bluetooth Stereo Headset and Intercom for outdoor sports and activities. With the SPH10, you can call handsfree on your Bluetooth mobile phone, listen to stereo music or voice instructions of GPS navigations by Bluetooth wirelessly, and have intercom conversations in full duplex with other SPH10 users. The SPH10 is compliant with the Bluetooth 3.
SPH10 2.
SPH10 3. WEARING THE SPH10 English • Boom Microphone • Mini Microphone 3.1 Microphone Installation • USB Power & Data Cable Two microphones are included in the package: a longboom microphone for high noise environment and a short microphone for indoor use. • Stereo Audio Cable • Boom Microphone Sponges Plug the microphone into the microphone port to fit triangle marks as described in the below picture.
SPH10 Since SPH10 is mostly exposed on external environment where noise prevails, microphone can be selected according to the noise level. For the highly noisy environment, boom-microphone is recommended allowing microphone to stay near user’s mouth. For the less-noisy environment, mini microphone is recommended allowing users to move freely. 3.2 Placing the Headset on Your Ear The speaker with microphone should be placed on the left ear. Then you can place earhooks over ears as shown: 4.
SPH10 4.5 Checking the Battery Level You can check the battery level in two different ways when the headset is powering on. 4.5.1 LED Indicator When the headset is powering on, the red LED flashes rapidly indicating the battery level. 4 flashes = High, 70~100% 3 flashes = Medium, 30~70% 2 flashes = Low, 0~30% 5. VOLUME ADJUSTMENT English 4.
SPH10 6. PAIRING THE SPH10 WITH BLUETOOTH DEVICES Before using the SPH10 Bluetooth headset with any of Bluetooth devices for the first time, you need to do the pairing operation. It can be paired with Bluetooth mobile phones, Bluetooth stereo devices such as MP3, or motorcycle specific Bluetooth GPS, and with other Sena Bluetooth headsets. This pairing operation is only required once for each Bluetooth device.
SPH10 1. If Bluetooth connection between the headset and a mobile phone is disconnected, tap the Phone Button to recover the Bluetooth connection immediately. 2. If Bluetooth connection between the headset and a media player is disconnected, press the Jog Dial for 1 second to recover the Bluetooth connection and play. 6.3 Bluetooth GPS Navigation Pairing You can listen to voice instruction from Bluetooth GPS navigation.
SPH10 The pairing diagram for multipoint GPS pairing is shown in the figure below. some GPS systems support mobile phone bridging over Bluetooth, you can pair the mobile phone to the GPS to use your mobile phone. Please refer to the user’s guide of your GPS for details. HFP Smart Phone HFP + Mobile Phone Pairing A2DP GPS Mobile Phone HFP + Mobile Phone Pairing (A2DP) HFP SPH10 Multipoint Pairing GPS Multipoint GPS Pairing SPH10 GPS Pairing as Mobile Phone 6.3.
SPH10 The Sena SR10 is a Bluetooth two-way radio adapter for group communication, and uses HFP as do most motorcycle specific GPS navigation systems. If you pair the SPH10 with a SR10 by multipoint pairing, the SPH10 is able to have two HFP devices at the same time: mobile phone and Sena SR10. 1. Turn on the headset and press the Jog Dial for 5 seconds until the red LED is rapidly flashing and you hear multiple beeps. 2.
SPH10 7. PAIRING WITH SELECTIVE PROFILE: A2DP STEREO OR HANDSFREE Smart Phone HFP + Mobile Phone Pairing A2DP Wired Connection HFP SPH10 If you have a MP3 stereo music phone such as a smartphone, sometimes you may need to selectively use the SPH10 for A2DP stereo music only or for mobile phone handsfree only. This instruction is for advanced users who want to pair the SPH10 to their smartphones only with one selective profile: A2DP stereo for music or HFP for phone call.
SPH10 7.2 HFP for Phone Call Only 1. Turn on the headset and press the Phone Button for 5 seconds until the LED flashes red and blue alternately and you hear multiple beeps. 2. Within 2 seconds, tap the Phone Button again, then the LED turns to blue flashing and the beeps turn to multiple mid-tone beeps. You will hear a voice prompt saying “Phone selective pairing”. 3. Search for Bluetooth devices on your smartphone. Select the Sena SPH10 in the list of devices detected on your phone. 4.
SPH10 5. The intercom pairing queue is ‘Last-Come, FirstServed’. If a headset has multiple paired headsets for intercom conversations, the last paired headset is set as first intercom friend. The previous intercom friend becomes second intercom friend, and third intercom friend. A B D C Note: Pairing A & B 4. You can make other pairings between the headset A and C, and between the headset A and D by following the same procedure as above.
SPH10 You can set the configuration of the SPH10 by the voice menu instruction as below. 1. To enter into voice configuration menu, press and hold the Jog Dial for 12 seconds until the LED shows solid blue and you hear high tone double beeps. You will also hear a voice prompt saying “Configuration menu”. 2. Rotate the Jog Dial clockwise or counter-clockwise to navigate between the menus. You will hear voice prompts for each menu items as below. 3.
SPH10 of beeps for an incoming call, you can answer the phone by saying “Hello” or any other word loudly. This is enabled from the factory but you can disable this. If this mode is disabled, you have to tap the Jog Dial or the Phone Button to answer an incoming call. 9.
SPH10 prompt, “Delete all pairings”, and tap the Phone Button to confirm. Taping the Jog Dial is not available for this setting. Voice Prompt “PLC setting” Factory Default Enable Enable Tap the Phone Button Voice Prompt “Exit configuration” Tap the Jog Dial Factory Default N/A Enable Tap the Phone Button Disable The PLC (Packet Loss Concealment) algorithm is enabled from the factory.
SPH10 10. FUNCTION PRIORITY The SPH10 operates in the following order of priority: (highest) Mobile phone, Intercom, Stereo music by audio cable, and (lowest) Bluetooth stereo music A lower priority function is always interrupted by a higher priority function. For example, stereo music is interrupted by intercom call, and intercom conversation is interrupted by incoming mobile phone call. 11.
SPH10 3. To track forward or track back, rotate while pressing the Jog Dial clockwise or counter clockwise. 1. To adjust the volume, rotate the Jog Dial. Note: 2. To play or pause music, press and hold the Jog Dial for 1 second until you hear a double beep. Bluetooth music is available only when the MP3 jack port remains open. Please make sure the audio cable is unplugged from the clamp unit to play music by Bluetooth.
SPH10 12. MOBILE PHONE CALL MAKING AND ANSWERING 1. When you have an incoming call, simply tap the Phone Button or the Jog Dial to answer the call. 2. You can also answer the incoming call by loudly speaking any word of your choice if Voice Activated Phone Answering is enabled. 3. To end a call, tap the Phone Button or press the Jog Dial for 2 seconds until you hear a beep, or wait for the called person to end the call. 4.
SPH10 13.1 Start and End Two-way Intercom 1. You can start an intercom conversation with one of any intercom friends by tapping the Jog Dial: single tapping to intercom with the first intercom friend, double tapping with the second intercom friend, and triple tapping with the third intercom friend.
SPH10 Button. When you hang up the phone call, the intercom will automatically be recovered. b. To reject the phone call and stay on the intercom conversation, press the Jog Dial for 2 seconds until you hear a beep. Unlike other motorcycle Bluetooth headsets, this prevents a user from being dropped out of an intercom conversation by an incoming mobile call. 2.
SPH10 English 14. THREE-WAY CONFERENCE INTERCOM 14.
SPH10 2. Start an intercom conversation with one of the two friends in your intercom group. For example, you (A) may start an intercom conversation with the intercom friend (B). Or intercom friend (B) may start an intercom call with you (A). (A) First Friend (B) Second Friend (C) (A) 24 (A) First Friend (B) 3. The second intercom friend (C) may join the intercom by making an intercom call to you (A). First Friend (B) 4.
SPH10 Jog Dial Operation Press for 1” Result Disconnect (B) & (C) Single tap Disconnect (B) Double tap Disconnect (C) End Three-way Intercom 15. FOUR-WAY CONFERENCE INTERCOM English However, you still have the intercom connection with your second intercom friend (C). 15.1 Start Four-way Intercom You can have four-way conference intercom with three other SPH10 users by adding one more intercom participant to the three-way intercom. While you are having three-way intercom as above in section 14.
SPH10 connection. 1. Press the Jog Dial for 1 second until you hear a beep to terminate four-way conference intercom. It terminates the intercom connections between you (A), and your intercom friends (B) and (C). 2. Tap or double tap the Jog Dial to disconnect the intercom connection with one of the two intercom friends accordingly. However, when you disconnect the second friend (C) by double tapping the Jog Dial, you will be disconnected with the third participant (D) as well.
SPH10 When you try to start an intercom conversation with an intercom friend who is already having a conference intercom with other riders or a mobile phone call, you will hear a low tone double beep signifying an intercom busy signal. In this case, you have to try again later. 18. INTERCOM RECONNECTION If your intercom friend goes out of range while having an intercom conversation, you may hear static noise and eventually the intercom will be disconnected.
SPH10 20. FAULT RESET When the SPH10 is not working properly or is in faulty status for any reason, you may reset by pushing the pin-hole reset button at the back of the headset main unit. Insert a paper clip into the reset pin-hole and press the reset button for a second with light pressure. The SPH10 will be switched off, and you have to turn the system back on and try again. However, this will not restore the headset to factory default settings. 22.
SPH10 Case 3 •iPhone for mobile phone call via ZumoTM 660/665 • ZumoTM 660/665 for GPS voice instruction and stereo music streaming •SPH10 for two-way intercom Pairing: Refer to ZumoTM 660/665 manual Mobile Call iPhone ZumoTM 660/665 iPhone Mobile Call Pairing: 6.1 Music Intercom Conversation GPS Voice Intercom Conversation Pairing: 6.3.1 ZumoTM 660/665 Pairing: 8.1 SPH10 Mobile Call Music Pairing: 6.1 GPS Voice Pairing: 8.
SPH10 Case 4 •Feature phone for mobile phone call •iPod Touch for stereo music streaming • Two other SPH10s for three-way conference intercom Case 5 •iPhone for mobile phone call •iPod Touch for stereo music streaming •TomTom® Rider2 for GPS voice instruction •SPH10 for two-way intercom Feature Phone iPhone Mobile Pairing: 7.2 Call Mobile Pairing: 6.1 Call SPH10 Intercom Conversation Music Pairing: 8.1 Pairing: 6.2 SPH10 Intercom Conversation Pairing: 8.
SPH10 Case 6 iPhone Two-way radio Mobile Call Pairing: 6.1 Music Wired Connection Tow-way radio GPS Voice Alarm Pairing: 6.4 SPH10 Intercom Conversation Pairing: 8.1 Wired Connection Sena SR10 Wired Connection Radar Detector SPH10 GPS with headphone jack/audio line-out BATTERY INFORMATION The SPH10 has an internal, non-removable, rechargeable battery. Do not attempt to remove the battery from the device as you may damage the device.
SPH10 MAINTENANCE AND CARE The SPH10 should be treated with care and the following suggestions will help you protect your warranty coverage. 1. Do not use or store the device in dusty, dirty areas. Its moving parts and electronic components can be damaged. 2. Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and wrap or melt certain plastics. 3. Do not store the device in cold areas.
SPH10 CERTIFICATION AND SAFETY APPROVALS The crossed-out wheel bin symbol on the product, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies to the European Union and other locations where separate collection systems are available.
SPH10 • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC RF Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
SPH10 Bluetooth License The SPH10 is compliant with and adopts the Bluetooth® Specification 3.0 and has successfully passed all interoperability tests that are specified in the Bluetooth® specification. However, interoperability between the device and other Bluetooth®-enabled products is not guaranteed. WAIVER AND GENERAL RELEASE By using the SPH10 you waive all substantial legal rights including the right to sue. Please read the following carefully before using the device.
SPH10 the Device while riding a Vehicle are solely intended to address its technical capabilities and should not be misconstrued as if encouraging users to operate the Device while actively involved in traffic.
SPH10 Two-Year Limited Warranty Sena Technologies, Inc. (“Sena”) warrants that this product (“Product”) shall conform to and perform in accordance with published technical specifications and the accompanying written materials, and shall be free of defects in materials and workmanship, for a period of two (2) year from the date of purchase by the first consumer purchaser of the Product.
SPH10 distributor it was purchased through and providing proof of purchase or receipt date. Customer agrees to insure the Product or assume the risk of loss or damage in transit, to prepay shipping charges to Sena, and to use the original shipping container or equivalent. SERVICES HEREUNDER OR THE PERFORMANCE, USE OR INABILITY TO USE THE SAME, EVEN IF SENA OR ITS DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SPH10 English WARNING Sena informs that using this device in public traffic may not be authorized by the law. Please check your local law and use this device only out of public traffic such as private properties or closed circuits. If the simultaneous use of both ear speakers while riding a motorcycle is prohibited by your local law, please use only a single ear speaker while riding. Sena denies any liability should you choose not to respect this warning.
2.0.0 www.senabluetooth.com Users Guide User's Guide for Firmware v4.
