www.senabluetooth.
SMH10 Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. SMH10™, SMH5™, SPH10™, SPH10S™, SPH10H™, SR10™, SM10™ are trademarks of Sena Technologies, Inc. or its subsidiaries. These trademarks may not be used without the express permission of Sena. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license. iPhone, iPod touch are the registered trademark of Apple Inc.
SMH10 CONTENTS 1. 2. 3. 4. INTRODUCTION PACKAGE CONTENTS INSTALLING THE SMH10 ON YOUR HELMET POWERING ON/OFF AND CHARGING 4.1 4.2 4.3 4.4 4.5 Powering On Powering Off Charging Low Battery Warning Checking the Battery Level 5. VOLUME ADJUSTMENT 6. PAIRING THE SMH10 WITH BLUETOOTH DEVICES 6.1 6.2 6.3 6.4 Mobile Phone Pairing Bluetooth Stereo Device Pairing Bluetooth GPS Navigation Pairing Pairing with the Sena SR10, Bluetooth Two-way Radio Adapter 7.
SMH10 Thank you for choosing the Sena SMH10, Bluetooth Stereo Headset and Intercom for Motorcycles. With the SMH10, you can call handsfree on your Bluetooth mobile phone, listen to stereo music or voice instructions of GPS navigations by Bluetooth wirelessly, and have intercom conversations in full duplex with a passenger or other motorcycle riders. The SMH10 is compliant with the Bluetooth 3.
SMH10 2.
SMH10 • Cigarette Charger • 3.5mm Stereo Audio Jack Cable • Glued Surface Mounting Adapter 3. INSTALLING THE SMH10 ON YOUR HELMET English • USB Power & Data Cable To securely install the SMH10 on the helmet, please follow the procedure. 1. Loosen the two screws on the back plate of the speaker-microphone clamp unit using the enclosed Allen Wrench. Insert the back plate of the clamp unit between the internal padding and external shell of the helmet, and tighten the two screws.
SMH10 2. Please adjust the direction of the microphone so that the fin side of the microphone is facing outward; away from your lips. You can easily recognize it by touching the fin with your fingers. fin When installing the boom microphone included in the “Universal Microphone Kit”, place the velcro end of the boom microphone between the internal helmet cheek pad and the internal wall of the helmet shell.
SMH10 Attach ena recommends the clamp unit over the glued surface mounting S adapter. Even though the glued surface mounting adapter is provided for convenience, Sena does not assume any responsibility for use of it. Users may have to use the glued adapter at their own risk and responsibility. 5. Attach the headset main unit to the speaker-microphone clamp unit. Insert the bottom part of the main unit completely into the lower slot of the clamp unit first.
SMH10 4. POWERING ON/OFF AND CHARGING To power on and off the headset, you don’t need to press and hold any button for several seconds. Just short press the Jog Dial and the Phone Button simultaneously, and you will get quick on-and-off convenience. 4.1 Powering On Press the Jog Dial and the Phone Button at the same time for about 1 second to power on. The blue LED turns on and you will hear ascending beeps. 4.
SMH10 You can easily adjust the volume by rotating the Jog Dial. You will hear a beep when the volume reaches maximum or minimum level. The volume is set and maintained independently at different levels for each audio source even when you turn off and on the headset. For example, once you set the volume for mobile phone handsfree, it will not change even if you adjust the volume when you hear Bluetooth MP3 music. So you can always maintain the preferred optimum volume level for each audio source. 6.
SMH10 4. The mobile phone confirms that pairing has completed and the SMH10 is ready to use. You will hear a voice prompt from the SMH10 saying “Your headset is paired”. 5. If the pairing process is not completed within three minutes, the SMH10 will return to stand-by mode. 6.2 Bluetooth Stereo Device Pairing 1. If the Bluetooth stereo device is integrated with the mobile phone such as smartphones, you don’t need to pair the SMH10 with it separately.
SMH10 The pairing diagram for multipoint GPS pairing is shown in the figure below. 6.3.2 GPS Pairing as Mobile Phone If GPS is not only used for turn-by-turn voice instructions but also is your preferred Bluetooth stereo music source, you can pair the GPS to the SMH10 by following the simple procedures in “6.1 Mobile Phone Pairing”. When you do this, the SMH10 thinks the GPS is a mobile phone so you can no longer pair your mobile phone to the SMH10 directly.
SMH10 Note: You have to use a motorcycle specific GPS which transmits turn-byturn voice instruction to the headset by Bluetooth. Most automotive GPS systems don’t have this feature. 6.4 Pairing with the Sena SR10, Bluetooth Two-way Radio Adapter The Sena SR10 is a Bluetooth two-way radio adapter for group communication, and uses HFP as do most motorcycle specific GPS navigation systems.
SMH10 Smart Phone Wired Connection HFP SMH10 If you have a MP3 stereo music phone such as a smartphone, sometimes you may need to selectively use the SMH10 for A2DP stereo music only or for mobile phone handsfree only. This instruction is for advanced users who want to pair the SMH10 to their smartphones only with one selective profile: A2DP stereo for music or HFP for phone call. Two-way radio HFP Mobile Phone + Pairing A2DP Multipoint Pairing Wired Connection Sena SR10 English 7.
SMH10 2. Within 2 seconds, tap the Jog Dial again, then the LED turns to red flashing and the beeps turn to double mid-tone beeps. You will hear a voice prompt saying “Media selective pairing”. 3. Search for Bluetooth devices on your smartphone. Select the Sena SMH10 in the list of devices detected on your phone. 4. Enter 0000 for the PIN. Some smartphones may not ask for PIN. 7.2 HFP for Phone Call Only 1.
SMH10 D B Note: C For example, after the pairing procedures listed above, headset D is the first intercom friend of headset A. Headset C is the second intercom friend of headset A, and headset B is the third intercom friend of headset Pairing A & B 4. You can make other pairings between the headset A and C, and between the headset A and D by following the same procedure as above. A A D B English 5. The intercom pairing queue is ‘Last-Come, First-Served’.
SMH10 9. SMH10 CONFIGURATION SETTING You can set the configuration of the SMH10 by the voice menu instruction as below. 1. To enter into voice configuration menu, press and hold the Jog Dial for 12 seconds until the LED shows solid blue and you hear high tone double beeps. You will also hear a voice prompt saying “Configuration menu”. 2. Rotate the Jog Dial clockwise or counter-clockwise to navigate between the menus. You will hear voice prompts for each menu items as below. 3.
SMH10 9.2 Enabling/Disabling Voice Activated Intercom Dial to restart the intercom. This is to prevent repeated unintentional intercom connections by strong wind noise. If you tap the Jog Dial to start an intercom conversation, it is not terminated by 20 seconds of silence. After turning SMH10 off and on, you can start intercom by voice again. 9.
SMH10 9.4 Enabling/Disabling PLC (Packet Loss Consealment) “PLC setting” Voice Prompt Factory Default Enable Factory Default N/A Enable Tap the Phone Button Enable Tap the Phone Button Disable Tap the Jog Dial Voice Prompt The PLC (Packet Loss Concealment) algorithm is enabled from the factory. It improves the audio quality of the intercom and mobile phone handsfree in the presence of data packet errors within the Bluetooth link. It is recommend that this setting is always enabled.
SMH10 The SMH10 operates in the following order of priority: (highest) (lowest) Mobile phone, Intercom, Stereo music by audio cable, and Bluetooth stereo music A lower priority function is always interrupted by a higher priority function. For example, stereo music is interrupted by intercom call, and intercom conversation is interrupted by incoming mobile phone call. 11. STEREO MUSIC English 10.
SMH10 You not only can adjust the volume but also use the functions such as play, pause, next track and previous track. 1. To adjust the volume, rotate the Jog Dial. 2. To play or pause music, press and hold the Jog Dial for 1 second until you hear a double beep. 20 3. To track forward or track back, rotate while pressing the Jog Dial clockwise or counter clockwise. Note: Bluetooth music is available only when the MP3 jack port remains open.
SMH10 1. When you have an incoming call, simply tap the Phone Button or the Jog Dial to answer the call. 2. You can also answer the incoming call by loudly speaking any word of your choice if Voice Activated Phone Answering is enabled. 3. To end a call, tap the Phone Button or press the Jog Dial for 2 seconds until you hear a beep, or wait for the called person to end the call. 4. To reject a call, press the Jog Dial for 2 seconds until you hear a beep while the phone is ringing. 5.
SMH10 13. TWO-WAY INTERCOM Terminate 13.1 Start and End Two-way Intercom 1. You can start an intercom conversation with one of any intercom friends by tapping the Jog Dial: single tapping to intercom with the first intercom friend, double tapping with the second intercom friend, and triple tapping with the third intercom friend.
SMH10 English incoming mobile call. 2. When you have an incoming intercom call during a mobile phone call, you will hear 4 high tone beeps, alerting you that there is an incoming intercom call. You will also hear a voice prompt saying “Intercom requested”. In this case, the intercom call does not override the mobile phone call because intercom has lower priority than mobile call. You have to hang up the mobile phone call to make or receive an intercom call.
SMH10 14. THREE-WAY CONFERENCE INTERCOM 14.1 Start Three-way Intercom Smart Phone Two-way radio HFP Mobile Phone + Pairing A2DP Wired Connection Audio from Two-way Radio SMH10 Multipoint Pairing Wired Connection GPS 1. You (A) need to be paired with two other friends (B & C) for threeway conference intercom.
SMH10 4. Now you (A) and two SMH10 intercom friends (B & C) are having a three-way conference intercom. English 2. Start an intercom conversation with one of the two friends in your intercom group. For example, you (A) may start an intercom conversation with the intercom friend (B). Or intercom friend (B) may start an intercom call with you (A). (A) (A) First Friend (B) First Friend (B) Second Friend (C) 3. The second intercom friend (C) may join the intercom by making an intercom call to you (A).
SMH10 Jog Dial Operation Press for 1” Result Disconnect (B) & (C) Single tap Disconnect (B) Double tap Disconnect (C) End Three-way Intercom 15. FOUR-WAY CONFERENCE INTERCOM 15.1 Start Four-way Intercom You can have four-way conference intercom with three other SMH10 users by adding one more intercom participant to the three-way intercom. While you are having three-way intercom as above in section 14.
SMH10 Jog Dial Operation Press for 1” Single tap Double tap Result Disconnect (B), (C) & (D) Disconnect (B) Disconnect (C) & (D) End Four-way Intercom 16. THREE-WAY CONFERENCE PHONE CALL WITH INTERCOM PARTICIPANT English 1. Press the Jog Dial for 1 second until you hear a beep to terminate four-way conference intercom. It terminates the intercom connections between you (A), and your intercom friends (B) and (C). 2.
SMH10 17. INTERCOM FAILURE When you try to start an intercom conversation with an intercom friend who is already having a conference intercom with other riders or a mobile phone call, you will hear a low tone double beep signifying an intercom busy signal. In this case, you have to try again later. 18. INTERCOM RECONNECTION If your intercom friend goes out of range while having an intercom conversation, you may hear static noise and eventually the intercom will be disconnected.
SMH10 The SMH10 supports firmware upgrade function. Please visit Sena Bluetooth web site at www.senabluetooth.com to check the latest software downloads. 22. CASE STUDY English 21. FIRMWARE UPGRADE Case 1 •iPhone for mobile phone call and stereo music streaming •ZumoTM 550 or ZumoTM 220 for GPS voice instruction •SMH10 for two-way intercom iPhone Mobile Call Music Intercom Conversation SMH10 Pairing: 8.1 Pairing: 6.1 GPS Voice SMH10 Pairing: 6.3.
SMH10 Case 3 Case 2 •iPhone for mobile phone call and stereo music streaming •ZumoTM 660/665 for GPS voice instruction •SMH10 for two-way intercom •iPhone for mobile phone call via ZumoTM 660/665 • ZumoTM 660/665 for GPS voice instruction and stereo music streaming •SMH10 for two-way intercom Pairing: Refer to ZumoTM 660/665 manual Mobile Call iPhone Mobile Call Music Intercom Conversation SMH10 Pairing: 8.1 ZumoTM 660/665 Pairing: 6.1 iPhone Mobile Call Music Pairing: 6.
SMH10 Case 4 Case 5 •iPhone for mobile phone call •iPod Touch for stereo music streaming •TomTom® Rider2 for GPS voice instruction •SMH10 for two-way intercom English •Feature phone for mobile phone call •iPod Touch for stereo music streaming •Two other SMH10s for three-way conference intercom Feature Phone iPhone Mobile Call Intercom Conversation SMH10 Pairing: 8.1 Pairing: 6.1 Mobile Call Music SMH10 Intercom Conversation Pairing: 6.2 Pairing: 8.1 Pairing: 7.
SMH10 Case 6 •iPhone for mobile phone call and stereo music streaming • Sena SR10 for two-way radio, GPS voice instruction, and radar detector alarm •SMH10 for two-way intercom iPhone Mobile Call Music Wired Connection Tow-way radio GPS Voice Alarm SMH10 Intercom Conversation SMH10 32 Pairing: 6.4 Pairing: 8.1 Wired Connection Sena SR10* Wired Connection Radar Detector The SMH10 has an internal, non-removable, rechargeable battery.
SMH10 DISPOSAL The crossed-out wheel bin symbol on the product, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies to the European Union and other locations where separate collection systems are available.
SMH10 CERTIFICATION AND SAFETY APPROVALS FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
SMH10 Industry Canada Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference (2) This device must accept any interference, including interference that may cause undesired operation of the device. Bluetooth License The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license.
SMH10 By way of purchasing this Device and not returning it for a full refund (see below), you are irrevocably releasing, indemnifying from any liability, loss, claim and expense (including attorney’s fees) and holding Sena harmless for any bodily injuries, harm or death as well as losses or damages in goods, to any Vehicles including your own, or to any property or asset that belong to you or to third parties, any of which may result from using the Device under any circumstances or conditions and irrespect
SMH10 Two-Year Limited Warranty Sena Technologies, Inc. (“Sena”) warrants that this product (“Product”) shall conform to and perform in accordance with published technical specifications and the accompanying written materials, and shall be free of defects in materials and workmanship, for a period of two (2) year from the date of purchase by the first consumer purchaser of the Product.
SMH10 THE SAME, EVEN IF SENA OR ITS DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL SENA OR ITS DEALERS TOTAL LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT. Return for Full Refund IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDITIONS, YOU MAY RETURN THIS DEVICE TO SENA FOR A FULL REFUND, PROVIDED THAT YOU DO SO NO LATER THAN 14 BUSINESS DAYS FOLLOWING THE PURCHASE OF THE DEVICE AND SUBJECT TO THE WRAPPING BEING INTACT. WHEN DOING SO, PLEASE REFER TO THIS SECTION.
3.0.0 www.senabluetooth.com User's Guide for Firmware v4.
