0R Low Profile Motorcycle Bluetooth Communication System
© 1998-2015 Sena Technologies, Inc. All rights reserved. Sena Technologies, Inc reserves the right to make any changes and improvements to its product without providing prior notice. Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. 10R™, 10U™, 10C™, Prism™, 20S™, Snowtalk™, 3S™, SMH10™, SMH5™, SMH5-FM™, SPH10™, SPH10H™, SPH10H-FM™, SMH10R™, SPH10S™, SPH10H™, ® SR10™, SR10i™, SM10™, EXPAND™, Bluetooth Pack for GoPro are trademarks of Sena Technologies, Inc.
CONTENTS 1 INTRODUCTION 2 PACKAGE CONTENTS 3 INSTALLING THE 10R ON YOUR HELMET 4 GETTING STARTED 4.1 Button Operation 4.2 Powering On and Off 4.3 Charging 4.4 Checking the Battery Level 4.4.1 LED Indicator 4.4.2 Voice Prompt Indicator 4.5 Volume Adjustment 4.6 Sena Softwares 4.6.1 Sena Device Manager 4.6.2 Sena Smartphone App 5 PAIRING THE 10R WITH BLUETOOTH DEVICES 5.1 Mobile Phone Pairing - Mobile Phone, Bluetooth Stereo Device 5.2 Second Mobile Phone Pairing - Second Mobile Phone, GPS, and SR10 5.
8.3.2 Ending Four-way Intercom 9 THREE-WAY CONFERENCE PHONE CALL WITH INTERCOM PARTICIPANT 10 UNIVERSAL INTERCOM 10.1 Universal Intercom Pairing 10.2 Two-way Universal Intercom 10.3 Three-way Universal Intercom 10.4 Four-way Universal Intercom 10.4.1 Four-way Universal Intercom Case 1 10.4.2 Four-way Universal Intercom Case 2 11 FM RADIO 11.1 FM Radio On/Off 11.2 Preset Stations 11.3 Seek and Save 11.4 Scan and Save 11.5 Temporary Preset 11.
CERTIFICATION AND SAFETY APPROVALS FCC Compliance Statement FCC RF Exposure Statement FCC Caution CE Declaration of Conformity Industry Canada Statement Bluetooth License WEEE (Waste Electrical and Electronic Equipment) SAFETY INFORMATION Product Storage and Management Product Use Battery PRODUCT WARRANTY AND DISCLAIMER Limited Warranty Warranty Exclusions Reasons for Limited Liabilities Limitation of Liability Liabilities Disclaimer Warranty Service Free-of-charge Service Charged Service Return for Full Re
1 INTRODUCTION Thank you for choosing the Sena 10R, Low Profile Bluetooth Stereo Headset and Intercom. With the 10R, you can call handsfree on your Bluetooth mobile phone, listen to stereo music or voice instructions of GPS navigations wirelessly, and have intercom conversations in full duplex with a passenger or other motorcycle riders. The 10R is compliant with the Bluetooth 4.
2 PACKAGE CONTENTS ● Headset Main Unit ● Speakers ● Attachable Boom Microphone ● Wired Microphone ● Battery Pack* ● Battery Pack Holder ● Speaker Pads ● Velcro Pad for Boom Microphone ● Velcro Pads for Speakers ● Velcro Pad for Wired Microphone ● Double Sided Adhesive Tapes for Battery Pack Holder ● Velcro Pads for Main Unit ● Double Sided Adhesive Tapes for Main Unit ● Microphone Sponges ● USB Power & Data Cable ● Cigarette Charger -------------------------------------------
3 INSTALLING THE 10R ON YOUR HELMET 메모 [2]: 스피커는 좌,우 분리되었음. 변경요 To securely install the main unit of the 10R, you can use the velcro pad or double sided adhesive tape. Please follow the procedure below. 1. Peel off the cover of the adhesive tape of the velcro pad and attach it on the back plate of the main unit. 2. Locate a suitable surface on your helmet to attach the unit, clean the location with a moistened towel, and allow to dry thoroughly. 3.
to the 2 pin connector of the main unit cable. To get rid of the battery pack from the battery pack holder, push the battery pack upward.
4 GETTING STARTED 4.1 Button Operation The 10R is mainly controlled by the Bluetooth Handlebar Remote. The two are paired from the factory and are ready for immediate use. If the Handlebar Remote runs out of battery, you can use the control buttons on the headset to operate all functions.
● ● Speed Dial Turn on/off FM tuner 4.2 Powering On and Off 4.2.1 Headset To power on the headset, press the Center Button and the (+) Button at the same time while hearing ascending beeps and a voice prompt, “Hello”. To power off the headset, press the Center Button and the (+) Button at the same time while hearing descending beeps and a voice prompt, “Goodbye”. 4.2.2 Handlebar Remote To power on the device, tap the Front Button and the blue LED will appear.
when you reboot the headset. For example, once you set the volume for mobile phone handsfree, it will not change even if you adjust the volume for your Bluetooth MP3 music. However, if you adjust the volume during stand-by mode, it will affect volume levels of every audio source. Function Volume up Volume down Handlebar Remote Headset Move the Joystick up Tap the (+) Button Move the Joystick down Tap the (-) Button Button Operation Table for Volume Adjustment 4.6 Sena Softwares 4.6.
5 PAIRING THE 10R WITH BLUETOOTH DEVICES Before using the 10R Bluetooth headset with any other Bluetooth devices for the first time, you will need to pair them togeth er. You can pair the 10R with Bluetooth mobile phones, Bluetooth stereo devices such as MP3 players, or motorcycle specifi c Bluetooth GPS navigation, and with other Sena Bluetooth headsets. The pairing operation is required only once for each Bluetooth device.
2. You have to use a motorcycle specific GPS, which transmits turn-by-turn voice instructions to the headset by Bluetooth. Most automotive GPS systems do not have this feature. 3. The Sena SR10 is a Bluetooth two-way radio adapter for group communication, and uses Hands-Free Profile. The incoming audio from the two-way radio via SR10 is heard in the background while having an intercom conversation or a mobile phone call. 4. The GPS navigation or a radar detector could be connected to the SR10 by wire.
conversation. If the pairing process is not completed within one minute, the 10R will return to stand-by mode. Pairing A & B 4. You can make other pairing between headsets A and C, and between headsets A and D by following the same procedure as above. 5. The intercom pairing queue is ‘Last-Come, First-Served’. If a headset has multiple paired headsets for intercom conversations, the last paired headset is set as first intercom friend.
Pairing Intercom Pairing Tap the Rear Button Tap the (+) Button Press the Front Button for 5 seconds Press the Center Button for 5 seconds Tap the Front Button of any one of the two headsets Tap the Center Button of any one of the two headsets Button Operation Table for Bluetooth Pairing
6 MOBILE PHONE, GPS, SR10 6.1 Mobile Phone Call Making and Answering 1. When you have an incoming call, simply tap the Rear Button or the Front Button to answer the call. 2. You can also answer the incoming call by loudly speaking any word of your choice if Voice Activated Phone Answering (VOX Phone) is enabled, unless you are connected to intercom. 3.
Note: 1. Make sure that you connect the mobile phone and the headset to use the speed dial function. 2. You need to assign speed dial numbers before using the speed dial (please refer to section 13.1, “Assigning Speed Dial”).
7 STEREO MUSIC 7.1 Bluetooth Stereo Music The Bluetooth audio device must be paired with the 10R by following the “Bluetooth Stereo Device Pairing” procedures described in the section 7.1. The 10R supports the Audio/Video Remote Control Profile (AVRCP), so if your Bluetooth audio device also supports the AVRCP, you can use the 10R to remotely control music playback. Not only can you adjust the volume but you can also use functions such as play, pause, next track and previous track. 1.
8 INTERCOM Please make sure your intercom devices are paired as described in section 5.4, “Intercom Pairing”. 8.1 Two-way Intercom 8.1.1 Starting Two-way Intercom You can start an intercom conversation with one of any intercom friends by tapping the Front Button: Tap the Front Button once to intercom with the first intercom friend, tap the Front Button twice to intercom with the second intercom friend, and tap the Front Button three times to intercom with the third intercom friend.
intercom conversation with the intercom friend (B). Or intercom friend (B) may start an intercom call with you (A). 3. The second intercom friend (C) may join the intercom by making an intercom call to you (A). 4. Now you (A) and two 10R intercom friends (B & C) are having a three-way conference intercom. 8.2.2 Ending Three-way Intercom You can completely terminate the conference intercom or just disconnect an intercom connection with one of your active intercom friends. 1.
Please note that in this case, the new participant (D) is an intercom friend of (C), not of you (A). 8.3.2 Ending Four-way Intercom As same in the case of three-way intercom, you can completely get out of the four-way conference intercom or just disconnect a single intercom connection. 1. Press the Front Button for 1 second until you hear a beep to terminate four-way conference intercom. It terminates the intercom connections between you (A), and your intercom friends (B) and (C). 2.
9 THREE-WAY CONFERENCE PHONE CALL WITH INTERCOM PARTICIPANT 1. When you have an incoming mobile phone call during an intercom conversation, you will hear a ring tone. You can choose whether to 1) answer the mobile phone call and stop the intercom conversation, or 2) reject the phone call and stay on the intercom conversation. a. To answer the phone call and stop the intercom conversation, tap the Rear Button or the Front Button. The VOX Phone feature does not work if you are connected to intercom.
10 UNIVERSAL INTERCOM You can have an intercom conversation with non-Sena Bluetooth headsets using the Universal Intercom function. Non-Sena Bluetooth headsets can be connected to the Sena Bluetooth headset if they support the Bluetooth Hands-Free Profile (HFP). The working distance may differ depending on the performance of Bluetooth headset that it is connected to. In general, it is shorter than normal intercom distance since it uses the Bluetooth Hands-Free Profile.
between the headset and the phone is disconnected temporarily. If you disconnect the intercom call, the mobile phone connection is made again automatically so that you can use a mobile phone call function. 1. You (A) need to be paired with a non-Sena Bluetooth headset (B) and another 10R headset (C) for the three-way conference intercom. 2. Start an intercom conversation with non-Sena Bluetooth headset (B) in your intercom group.
none-Sena Bluetooth headset or 2) two 10Rs and two non-Sena Bluetooth headsets. You may have a couple of other Four-way Universal Intercom configurations, 1) your headset (A), a non-Sena Bluetooth headset (B), another 10R (C), and a non-Sena Bluetooth headset (D), 2) your headset (A), a non-Sena Bluetooth headset (B), and two other 10R headsets (C and D). You may make the four-way Universal Intercom call the same way as a normal fourway intercom call. 10.4.
10.4.2 Four-way Universal Intercom Case 2 Three 10R headsets (A, C and D) and one non-Sena Bluetooth headset (B) The procedure is the same as case 1 described in section 11.4.1.
11 FM RADIO 11.1 FM Radio On/Off To turn on the FM radio, press the Rear Button for 1 second until you hear a mid-toned double beep sound. You will then hear a voice prompt, “FM on”. To turn off the FM radio, press the Rear Button for 1 second until you hear a voice prompt, “FM off”. When you power it off, the 10R will remember the last station frequency. When you power it on, the last station frequency will be playing. 11.2 Preset Stations You can listen to preset stations while listening to the FM radio.
11.5 Temporary Preset With the temporary preset function, you may temporarily preset stations automatically without changing the existing preset stations. Tap the Rear Button three times to automatically scan for 10 temporary preset stations. The temporary preset stations will be cleared when the system is powered off. 11.6 Region Selection You can select the proper FM frequency region from the Sena Device Manager.
12 FUNCTION PRIORITY The 10R operates in the following order of priority: (highest) Mobile phone Intercom Music sharing by Bluetooth stereo music FM Radio (lowest) Bluetooth stereo music A lower priority function is always interrupted by a higher priority function. For example, stereo music is interrupted by intercom call, and an intercom conversation is interrupted by an incoming mobile phone call.
13 CONFIGURATION SETTING You can set the configuration of the 10R by the voice menu instruction described below. 1. To enter into voice configuration menu, press and hold the Front Button for 12 seconds until the LED shows solid blue and you hear high toned double beeps. You will also hear a voice prompt, “Configuration menu”. 2. Move the Joystick up or down to navigate between the menus. You will hear voice prompts for each menu item as below. 3.
13.1 Mobile Phone Pairing Voice Prompt "Phone pairing" Factory Default N/A To go into mobile phone pairing mode, tap the (+) Button or the (-) Button until you hear the voice prompt, “Phone pairing”. Please refer to section 5.1 for details on mobile phone pairing. If you tap the (+) Button or the (-) Button, you can exit from the phone pairing mode. 13.
13.5 Assigning Speed Dial Voice Prompt "Speed dial" Factory Default N/A Execute Tap the Center 1. To assign a phone number as a speed dial, tap the (+) Button or the (-) Button until you hear a voice prompt, “Speed dial”. 2. Tap the Center Button, and you will hear a voice prompt, “Speed dial one” and “Phone connected”. 3. Tap the (+) Button or the (-) Button to select one of three speed dial numbers and you hear a voice prompt, “Speed dial (#)”. 4.
disabled if you are connected to intercom. If this feature is disabled, you have to tap the Center Button to answer an incoming call. 13.8 Enabling/Disabling Voice Activated Intercom Voice Prompt “VOX intercom” Factory Default Disable Enable/Disable Tap the Center Button If this feature is enabled, you can initiate an intercom conversation with the last connected intercom friend by voice. When you want to start intercom, say a word such as “Hello” loudly or blow air into the microphone.
- Voice prompts for configuration setting menu - Voice prompts for battery level indicator - Voice prompts for speed dial - Voice prompts for FM radio functions 13.11 Enabling/Disabling RDS AF Voice Prompt “RDS AF setting” Factory Default Enable Enable/Disable Tap the Center Button RDS AF allows a receiver to re-tune to the second frequency location when the first signal becomes too weak. With RDS AF enabled on the receiver, a radio station with more than one frequency can be used. 13.
Voice Prompt “Delete all pairings” Factory Default Execute N/A Tap the Center Button To delete all Bluetooth pairing information of the 10R, tap the (+) Button or the (-) Button until you hear a voice prompt, “Delete all pairings”, and tap the Center Button to confirm. 13.
Tap (+) Button or (-) Button Tap Center Button Phone Pairing None Second Mobile Phone Pairing None Phone Selective Pairing None Media Selective Pairing None Speed Dial Execute Audio Boost Enable/Disable VOX Phone Enable/Disable VOX Intercom Enable/Disable VOX Sensitivity -Enter adjustment mode - Save and exit Voice Prompt Enable/Disable RDS AF Setting Enable/Disable Sidetone Enable/Disable Advanced Noise Control Enable/Disable Delete All Pairings Execute Factory Reset Execute
14 FIRMWARE UPGRADE The 10R supports firmware upgrades. You can update the firmware using the Sena Device Manager (please refer to section 4.6.1, “Sena Device Manager”). Please visit Sena Bluetooth website at www.sena.com to check the latest software downloads.
15 TROUBLESHOOTING 15.1 Intercom Failure When you try to start an intercom conversation with an intercom friend who is unavailable within range or already having a conference intercom with other riders or a mobile phone call, you will hear a low tone double beep signifying an intercom busy signal. In this case, you have to try again later. 15.
16 OPERATION QUICK REFERENCE Type Basic Function Mobile Phone Function Button Duration LED Beep Power on Center Button & (+) Button 1 sec Solid blue Ascending beeps Power off Center Button & (+) Button Tap Solid red Descending beeps Volume adjustment (+) Button or (-) Button Tap - - Answer & end phone call Center Button Tap - - Speed dial (+) Button 3 secs - Mid-tone single beep Reject incoming call Center Button 2 secs - - Center Button 5 secs Red flashing Mid-tone s
Save preset while scanning (-) Button tap - High tone double beeps
CERTIFICATION AND SAFETY APPROVALS FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules.
Industry Canada Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. Bluetooth License ® The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license.
● In some regions, it is prohibited by law to ride motorcycles or bicycles while wearing headsets. Therefore be certain to comply with all relevant laws in the region before using the product. ● Use of the product at a high volume for a long period of time may damage your eardrums or hearing ability. Keep the volume at a modest level. ● Do not cause impact to the product or touch it with sharp tools as this may damage the product.
PRODUCT WARRANTY AND DISCLAIMER Limited Warranty Limited Warranty Sena Technologies, Inc. (“Sena”) guarantees the product quality based on the technical specification stated in the product manual, and data regarding product warranty. Here, product warranty extends to the product only. Sena will not be liable for any loss, damage of human life, or loss of property which may result from using the product beyond defective parts or flaws that occur due to problems in manufacture.
● When you use the product while you operating any vehicle or equipment such as motorcycles, scooters, mopeds, ATVs, or quad-bikes (hereinafter called as "transportation means"), you must take complete caution regardless of the location of such operation. ● Use of the product on the road may cause such risks as fracture, serious disability, or death.
In addition to damages which may occur due to the use of the product, Sena will not be liable for damages of the product which occur due to the following events. In the event the product is misused or used for purposes other than its intended purposes. In the event the product is damaged because the user does not follow the content of the product manual. In the event the product is damaged because it has been left unattended or has undergone any other accident.
1.0.0 CERTIFICATION ET HOMOLOGATION EN TERMES DE SÉCURITÉ Déclaration de conformité FCC Cet appareil est en conformité avec la partie 15 de la réglementation FCC. L'exploitation est autorisée aux deux conditions suivantes : (1) Cet appareil ne doit pas créer d’interférences préjudiciables et (2) Cet appareil doit accepter toutes les interférences reçues, y compris celles qui pourraient entraver son bon fonctionnement.
Déclaration de conformité IC (Industrie Canada) Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) Cet appareil ne doit pas créer d'interférences. (2) Cet appareil doit accepter toutes les interférences reçues, y compris celles qui pourraient entraver son bon fonctionnement.
Utilisation du produit ● Dans certaines régions, la loi interdit le port d'écouteurs en étant à moto ou à vélo. Assurez-vous donc de respecter toutes les lois correspondantes dans la région avant d'utiliser le produit. ● L'utilisation du produit à volume élevé pendant une période prolongée peut endommager les tympans ou la capacité auditive. Garder le volume sonore à un niveau modéré. ● Ne pas heurter le produit ou le toucher avec des outils tranchants car cela pourrait l'endommager.
● ● Ne jamais utiliser un chargeur endommagé. Il pourrait exploser et/ou causer des accidents. La durée de vie de la batterie dépend des conditions, des facteurs environnementaux, des fonctions en cours d'utilisation du produit et des appareils utilisés conjointement. Garantie limitée Garantie limitée Sena Technologies, Inc. (« Sena ») garantit la qualité du produit sur la base des caractéristiques techniques énoncées dans le manuel du produit et les données concernant la garantie du produit.
● Sena, en collaboration avec les employés, responsables, partenaires, filiales, représentants, agents, entreprises et fournisseurs impliqués, seuls vendeurs de Sena (collectivement désignés comme « l'entreprise ») vous recommandent, avant d'utiliser le produit et des appareils similaires de différentes marques y compris leurs modèles dérivés, de recueillir à l'avance toutes les informations pertinentes et d'être entièrement préparé quant aux conditions météorologiques et routières ainsi qu'à l'état de la
POUR LE PRODUIT PAR L'ACHETEUR. Exonération de responsabilités Outre les dommages pouvant survenir en raison de l'utilisation du produit, Sena n'est pas tenu responsable des dommages du produit survenant en raison des situations suivantes. ● Dans le cas où il est fait mauvais usage du produit ou qu'il est utilisé dans un but autre que celui prévu. ● Dans le cas où le produit est endommagé car l'utilisateur ne suit pas le contenu du manuel du produit.
SENA www.sena.com User's Guide for Firmware v1.
