0C Motorcycle Bluetooth Camera & Communication System ® SENA www.sena.
© 1998-2015 Sena Technologies, Inc. All rights reserved. Sena Technologies, Inc reserves the right to make any changes and improvements to its product without providing prior notice. Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. 20S™, PRISM™, Snowtalk™, 3S™, SMH10™, SMH5™, SMH5-FM™, SPH10™, SPH10H-FM™, SMH10R™, SPH10S™, SPH10H™, SR10™, SR10i™, SMH10™, EXPAND™, Bluetooth Pack for GoPro® are trademarks of Sena Technologies, Inc. or its subsidiaries.
CONTENTS 1 INTRODUCTION 2 PACKAGE CONTENTS 3 INSTALLING THE 10C ON YOUR HELMET 4 GETTING STARTED 4.1 Button Operation 4.2 Powering On and Off 4.3 Charging 4.4 Checking the Battery Level 4.4.1 LED Indicator 4.4.2 Voice Prompt Indicator 4.5 Volume Adjustment 4.6 Sena Softwares 4.6.1 Sena Device Manager 4.6.2 Sena Smartphone App 5 CAMERA OPERATION 5.1 Camera On or Off 5.2 Camera Modes 5.3 Video Recording 5.4 Photo Shooting 5.5 Video Tagging 5.6 Playback 6 PAIRING THE 10C WITH BLUETOOTH DEVICES 6.
9.1 Two-way Intercom 9.1.1 Starting Two-way Intercom 9.1.2 Ending Two-way Intercom 9.2 Three-way Intercom 9.2.1 Starting Three-way Intercom 9.2.2 Ending Three-way Intercom 9.3 Four-way Intercom 9.3.1 Starting Four-way Intercom 9.3.2 Ending Four-way Intercom 10 THREE-WAY CONFERENCE PHONE CALL WITH INTERCOM PARTICIPANT 11 UNIVERSAL INTERCOM 11.1 Universal Intercom Pairing 11.2 Two-way Universal Intercom 11.3 Three-way Universal Intercom 11.4 Four-way Universal Intercom 11.4.
15 FIRMWARE UPGRADE 16 TROUBLESHOOTING 16.1 Intercom Failure 16.2 Intercom Reconnection 16.3 Fault Reset 16.
1 INTRODUCTION Thank you for choosing the Sena 10C, Motorcycle Bluetooth Camera & Communication System. With the 10C, you can record videos, take photos, call handsfree on your Bluetooth mobile phone, listen to stereo music or voice instructions of GPS navigations wirelessly, and have intercom conversations in full duplex with a passenger or other motorcycle riders. The 10C is compliant with the Bluetooth 4.
● Supporting profiles: Headset Profile, Hands-Free Profile (HFP), Advanced Audio Distribution Profile (A2DP), and Audio Video Remote Control Profile (AVRCP).
2 PACKAGE CONTENTS 10C Headset Main Unit 10C Clamp Unit 10C Glued Surface Mounting Plate Speakers Wired Boom Microphone Wired Microphone USB Power & Data Cable Microphone Sponge (2) Velcro Pad for Speaker (2) Velcro Pad for Wired Boom Microphone Velcro Pad for Wired Microphone Boom Microphone Holder Velcro Pad for Boom Microphon Holder Foam Speaker Covers (2) Speaker Pad (Thick) (2) Speaker Pad (Thin) (2) Allen Wrench Cigarette Charger
3 INSTALLING THE 10C ON YOUR HELMET 1. Loosen the two screws on the back plate of the clamp using the enclosed Allen Wrench. Insert the back plate of the clamp unit between the internal padding and external shell of the helmet, and tighten the two screws. 2. Attach the headset main unit to the clamp. Insert the main unit in the clamp until you feel the click that signals a secure attachment. 3.
4 GETTING STARTED 4.
4.4.1 LED Indicator When the headset is powering on, the red LED flashes rapidly indicating the battery level. 4 flashes = High, 70~100% 3 flashes = Medium, 30~70% 2 flashes = Low, 0~30% 4.4.2 Voice Prompt Indicator When you power on the headset, keep pressing the Jog Dial and the Phone Button simultaneously for about 3 seconds until you hear high tone triple beeps. Then you will hear a voice prompt indicating the battery level is high, medium, or low. 4.
5 CAMERA OPERATION 5.1 Camera On or Off To turn on or off the camera, press the Camera Button and the Phone Button simultaneously. The green LED turns on while the camera is on. The camera goes to sleep mode after five minutes of inactivity. To wake up the camera, tap the Camera Button. 5.
1GB 9 min 12 min 24 min 2GB 18 min 24 min 48 min 4GB 36 min 48 min 1 h 36 min 8GB 1 h 12 min 1 h 36 min 3 h 12 min 16GB 2 h 24 min 3 h 12 min 6 h 24 min 32GB 4 h 48 min 6 h 24 min 12 h 48 min Note: - You cannot record videos without a micro SD card. - The headset gives a warning and automatically stops recording when the micro SD card is full or the battery runs out. Your video will be saved before the headset powers off.
3. Move right and left by rotating the Jog Dial clockwise or counter clockwise. 4. Select an item or play a video by tapping the Camera Button. 5. Move back or cancel by tapping the Jog Dial. Note: You can choose to view only videos, only photos, or all videos and pictures by tapping the Phone Button.
6 PAIRING THE 10C WITH BLUETOOTH DEVICES Before using the 10C Bluetooth headset with any other Bluetooth devices for the first time, you will need to pair them together. You can pair the 10C with Bluetooth mobile phones, Bluetooth stereo devices such as MP3 players, or motorcycle specific Bluetooth GPS navigation, and with other Sena Bluetooth headsets. The pairing operation is required only once for each Bluetooth device.
5. The HFP device confirms that the pairing is completed and the 10C is ready to use. You will hear a voice prompt, “Your headset is paired”. Note: - If the GPS is also your preferred Bluetooth stereo music source, you can pair the GPS to the 10C by following the simple procedures in “6.1 Mobile Phone Pairing”. - You have to use a motorcycle specific GPS, which transmits turn-by-turn voice instructions to the headset by Bluetooth. Most automotive GPS systems do not have this feature.
Pairing A & C Pairing A & D 5. The intercom pairing queue is ‘Last-Come, First-Served’. If a headset has multiple paired headsets for intercom conversations, the last paired headset is set as first intercom friend. The previous intercom friend becomes second intercom friend, and third intercom friend. Note: For example, after the pairing procedures listed above, headset D is the first intercom friend of headset A.
4. Enter 0000 for the PIN. Some smartphones may not ask for PIN. 7 MOBILE PHONE, GPS, SR10 7.1 Mobile Phone Call Making and Answering 1. When you have an incoming call, simply tap the Phone Button or the Jog Dial to answer the call. 2. You can also answer the incoming call by loudly speaking any word of your choice if Voice Activated Phone Answering (VOX Phone) is enabled, unless you are connected to intercom. 3.
4. After selecting the last number redial menu, you will hear a voice prompt, “Last number redial”. Then, to redial the last phone call number, tap the Phone Button. 5. To call one of the speed dials, rotate the Jog Dial clockwise or counter-clockwise to navigate between the menus until you hear a voice prompt, “Speed dial (#)”. Then, tap the Phone Button. 6. If you want to exit the speed dial immediately, rotate the Jog Dial until you hear a voice prompt, “Cancel”, and tap the Phone Button or the Jog Dial.
8 STEREO MUSIC 8.1 Bluetooth Stereo Music The Bluetooth audio device must be paired with the 10C by following the “Bluetooth Stereo Device Pairing” procedures described in the section 7.1. The 10C supports the audio/Video Remote Control Profile (AVRCP), so if your Bluetooth audio device also supports the AVRCP, you can use the 10C to remotely control music playback. Not only can you adjust the volume but you can also use functions such as play, pause, next track and previous track. 1.
9 INTERCOM Please make sure your intercom devices are paired as described in section 6.3, “Intercom Pairing”. 9.1 Two-way Intercom 9.1.1 Starting Two-way Intercom You can start an intercom conversation with one of any intercom friends by tapping the Jog Dial: single tap to intercom with the first intercom friend, double tap to intercom with the second intercom friend, and triple tap to intercom with the third intercom friend. Start Two-way Intercom Conversation (10C 그림으로 교체) 9.1.
2. Start an intercom conversation with one of the two friends in your intercom group. For example, you (A) may start an intercom conversation with the intercom friend (B). Or intercom friend (B) may start an intercom call with you (A). 3. The second intercom friend (C) may join the intercom by making an intercom call to you (A). 4. Now you (A) and two 10C intercom friends (B & C) are having a three-way conference intercom. 9.2.
Single tap Disconnect (B) Double tap Disconnect (C) End Three-way Intercom 9.3 Four-way Intercom 9.3.1 Starting Four-way Intercom You can have four-way conference intercom with three other 10C users by adding one more intercom participant to the three-way intercom. While you are having a three-way intercom as above in section 9.2, a new participant (D), who is an intercom friend of your intercom friend (C), may join the conference intercom by making an intercom call to your intercom friend (C).
10 THREE-WAY PARTICIPANT CONFERENCE PHONE CALL WITH INTERCOM 1. When you have an incoming mobile phone call during an intercom conversation, you will hear a ring tone. You can choose whether to 1) answer the mobile phone call and stop the intercom conversation, or 2) reject the phone call and stay on the intercom conversation. a. To answer the phone call and stop the intercom conversation, tap the Jog Dial or the Phone Button. The VOX Phone feature does not work if you are connected to intercom.
11 UNIVERSAL INTERCOM You can have an intercom conversation with non-Sena Bluetooth headsets using the Universal Intercom function. NonSena Bluetooth headsets can be connected to the Sena Bluetooth headset if they support the Bluetooth Hands-Free Profile (HFP). The working distance may differ depending on the performance of Bluetooth headset that it is connected to. In general, it is shorter than normal intercom distance since it uses the Bluetooth Hands-Free Profile.
11.3 Three-way Universal Intercom You may make a three-way Universal Intercom connection with two 10Cs and one non-Sena Bluetooth headset. If the intercom connection is made, all headsets connected cannot use the mobile phone call function since the connection between the headset and the phone is disconnected temporarily. If you disconnect the intercom call, the mobile phone connection is made again automatically so that you can use a mobile phone call function. 1.
11.4 Four-way Universal Intercom You may make a four-way Universal Intercom connection with a couple of different configurations, 1) three 10Cs and one non-Sena Bluetooth headset or 2) two 10Cs and two non-Sena Bluetooth headsets. You may have a couple of other four-way Universal Intercom configurations, 1) your headset (A), a non-Sena Bluetooth headset (B), another 10C (C), and a non-Sena Bluetooth headset (D), 2) your headset (A), a non-Sena Bluetooth headset (B), and two other 10C headsets (C and D).
You may disconnect a four-way Universal Intercom using the same way as you do in a normal four-way intercom. Please refer to section 9.3.2 “End Four-way Intercom”. 11.4.2 Four-way Universal Intercom Case 2 Three 10C headsets (A, C and D) and one non-Sena Bluetooth headset (B) The procedure is the same as case 1 described in section 13.4.1.
12 FM RADIO 12.1 FM Radio On/Off To turn on the FM radio, press and hold the Phone Button for 2 seconds until you hear a mid-toned double beep sound. You will then hear a voice prompt, “FM on”.To turn off the FM radio, press and hold the Phone Button for 2 seconds until you hear a voice prompt, “FM off”. When you power it off, the 10C will remember the last station frequency. When you power it on, the last station frequency will be playing. 12.
3. Scan function stops when you double tap the Phone Button again. 4. To save a station while scanning frequencies, tap the Phone Button when at that station. You will hear a voice prompt from the 10C, “Save preset (#)”. The station will be saved as the next preset number. 5. All stations preset during “Scan”, will overwrite previously set stations. 12.5 Temporary Preset With the temporary preset function, you may temporarily preset stations automatically without changing the existing preset stations.
13 FUNCTION PRIORITY The 10C operates in the following order of priority: (highest) Mobile phone Intercom Camera FM Radio (lowest) Bluetooth stereo music A lower priority function is always interrupted by a higher priority function. For example, stereo music is interrupted by intercom call, and an intercom conversation is interrupted by an incoming mobile phone call.
14 CONFIGURATION SETTING 14.1 Headset Configuration Setting You can set the configuration of the 10C by the voice menu instruction as below. 1. To enter into voice configuration menu, press and hold the Jog Dial for 12 seconds until the LED shows solid blue and you hear high toned double beeps. You will also hear a voice prompt “Configuration menu”. 2. Rotate the Jog Dial clockwise or counter clockwise to navigate between the menus. You will hear voice prompts for each menu item as below. 3.
- Rotate the Jog Dial to select one of three speed dial numbers by hearing voice prompts “Speed dial (#)”. 3. Call a phone number you want to assign and you will hear a voice prompt, “Save speed dial (#)”. The phone number is automatically assigned to the selected speed dial number. Then the phone call will hang up immediately. 4. To exit the menu, rotate the Jog Dial clockwise or counter clockwise until you hear a voice prompt, “Cancel”, and tap the Phone Button to confirm.
However, if you start intercom by voice and end it manually by tapping the Jog Dial, you will not be able to start intercom by voice temporarily. In this case, you have to tap the Jog Dial to restart the intercom. This is to prevent repeated unintentional intercom connections by strong wind noise. After rebooting the 10C, you can start intercom by voice again. 14.1.
Rotate Jog Dial Tap Phone Button Tap Jog Dial Speed Dial Execute N/A VOX Phone Enable Disable VOX Intercom Enable Disable Voice Prompt Enable Disable Delete All Pairings Execute N/A Exit Configuration Execute N/A Voice Configuration Menu & Button Operations 14.2 Camera Configuration Setting You can enter into camera configuration of the 10C by following the steps below: 1.
14.2.1 Photo Mode You can select the photo mode to be either single shot or burst shot. Single shot takes a single photo while burst shot takes 10 photos in one second. When you hear the voice prompt, “Photo mode setting”, tap the Phone Button to enter. Then rotate the Jog Dial to select either single shot or burst shot. Tap the Phone Button to save the mode.
Factory Default Select Mode Apply 1080p/30fps Rotate Jog Dial (1080p/30fps, 720p/60fps, 720p/30fps) Tap the Phone Button 14.2.4 Timelapse Interval Setting You can select the timelapse interval to be either 1 second or 10 seconds. When you hear the voice prompt, “Video mode resolution”, tap the Phone Button to enter. Then rotate the Jog Dial to select the interval. Tap the Phone Button to save the interval.
You can set the camera to automatically power off after five minutes of inactivity. This feature does not work while charging the camera. When you hear the voice prompt, “Auto camera sleep”, tap the Phone Button to either turn on or off this feature. Voice Prompt Factory Default On/Off “Auto camera sleep” On Tap the Phone Button 14.2.8 SD Card Format SD card format will remove all files from a micro SD card. When you use a new card for the first time, always format it before using the camera.
15 FIRMWARE UPGRADE The 10C supports firmware upgrades. You can update the firmware using the Sena Device Manager (please refer to section 4.6.1, “Sena Device Manager”). Please visit Sena Bluetooth website at www.sena.com to check the latest software downloads.
16 TROUBLESHOOTING 16.1 Intercom Failure When you try to start an intercom conversation with an intercom friend who is unavailable within range or already having a conference intercom with other riders or a mobile phone call, you will hear a low tone double beep signifying an intercom busy signal. In this case, you have to try again later. 16.
17 OPERATION QUICK REFERENCE Type Basic Function Camera Function Function Button Command LED Beep Power on Press the Phone Button and the Jog Dial for 1 second Solid blue Ascending beeps Power off Press the Phone Button and the Jog Dial Solid red Descending beeps Volume adjustment Rotate the Jog Dial - - Camera on/off Tap the Camera Button and the Phone Button Green Flashing - Video start/stop Press the Camera Button for 1 second Green Flashing - Photo shoot Tap the Camera Button
Music FM radio Play/Pause Bluetooth music Press the Jog Dial for 1 second - Mid-tone double beep Track forward/back Rotate the Jog Dial while pressing - - FM radio on Press the Phone Button for 2 seconds - Mid-tone double beeps FM radio off Press the Phone Button for 2 seconds - Mid-tone double beeps - Mid-tone single beep High tone triple beeps Select preset Tap the Phone Button Seek stations Rotate the Jog Dial while pressing - Scan up FM band Double tap the Phone Button - Stop
CERTIFICATION AND SAFETY APPROVALS FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules.
Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal, Spain, Sweden, United Kingdom and within EFTA in Iceland, Norway and Switzerland. Industry Canada Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
as this may damage the product. ● Do not paint the product. Paint may obstruct moving parts or interfere with the normal operation of the product. ● Do not drop or otherwise shock the product. It may damage the product or its internal electronic circuits. ● Do not disassemble, repair or modify the product as this may damage the product and invalidate the product warranty. Product Use ● In some regions, it is prohibited by law to ride motorcycles or bicycles while wearing headsets.
performance of the battery. ● Store the battery at temperatures of 15°C~25°C (59°F~77°F). Higher or lower temperatures may reduce the capacity and life of the battery, or may cause temporary non-operation. Do not use the product in sub-zero temperature, because it may cause serious reduction of the battery performance. ● If you apply heat to the battery or throw it into fire, it may explode. ● Do not use the product with a damaged battery. It may explode and/or cause accidents.
of this product will constitute consent to this agreement, and forfeiture of rights to all claims. If you do not consent to all the terms and conditions of this agreement, return the product for a refund. (Refer to the section "Return for Full Refund".) 1.
Limitation of Liability TO THE FULL EXTENT ALLOWED BY LAW, SENA EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS, EVEN IF SENA O
Sena will provide charged repair or replacement service for the product when the product warranty period has been expired or when the product damage is beyond the scope of the product warranty. For further information on charged service, you may contact the service center of Sena. Return for Full Refund Should you not agree to the terms and conditions explained above, you may return the product for a full refund.
