www.senabluetooth.
SPH10S Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. SMH10™, SMH5™, SPH10™, SPH10S™, SPH10H™, SR10™, SM10™ are trademarks of Sena Technologies, Inc. or its subsidiaries. These trademarks may not be used without the express permission of Sena. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license. iPhone, iPod touch are registered trademarks of Apple Inc.
SPH10S CONTENTS 1. INTRODUCTION 2. PACKAGE CONTENTS 3. INSTALLING THE SPH10S ON YOUR HELMET 4. POWERING ON/OFF AND CHARGING 3 4 5 6 4.1 Powering On 6 4.2 Powering Off 6 4.3 Charging 6 4.4 Low Battery Warning 7 4.5 Checking the Battery Level 7 5. VOLUME ADJUSTMENT 7 6. PAIRING THE SPH10S WITH BLUETOOTH DEVICES 8 6.1 Mobile Phone Pairing 8 6.2 Bluetooth Stereo Device Pairing 8 7. PAIRING WITH SELECTIVE PROFILE: A2DP STEREO OR HANDSFREE 9 7.1 A2DP Stereo Music Only 9 7.2 HFP for Phone Call Only 9 8.
SPH10S Thank you for choosing the Sena SPH10S, Bluetooth ® Headset & Intercom designed for snow sports helmets. With the SPH10S, you can call handsfree on your Bluetooth mobile phone, listen to stereo music and have intercom conversations in full duplex with other SPH10S users. The SPH10S is compliant with the Bluetooth 3.0 supporting the following profiles: Headset Profile, Hands-Free Profile (HFP), Advanced Audio Distribution Profile (A2DP), and Audio Video Remote Control Profile (AVRCP).
SPH10S 2.
SPH10S • Stereo Audio Cable 3. INSTALLING THE SPH10S ON YOUR HELMET English • USB Power and Data Cable 1. Remove the original ear flaps of your helmet and insert the plastic plate of SPH10S into where the ear flaps are removed in the helmet. 2. Please make sure that one of headset ear flaps with the microphone is located to the left side of your helmet. 3. Put the wire connected with ear flaps into the rear part of you helmet.
SPH10S 4. POWERING ON/OFF AND CHARGING To power on and off the headset, you don’t need to press and hold any button for several seconds. Just short press the Jog Dial and the Phone Button simultaneously, and you will get quick on-and-off convenience. 4.1 Powering On Press the Jog Dial and the Phone Button at the same time for about 1 second to power on. The blue LED turns on and you will hear ascending beeps. 4.
SPH10S You can easily adjust the volume by rotating the Jog Dial. You will hear a beep when the volume reaches maximum or minimum level. The volume is set and maintained independently at different levels for each audio source even when you turn off and on the headset. For example, once you set the volume for mobile phone handsfree, it will not change even if you adjust the volume when you hear Bluetooth MP3 music. So you can always maintain the preferred optimum volume level for each audio source. 6.
SPH10S detected on the mobile phone. 3. Enter 0000 for the PIN. Some mobile phone may not ask for the PIN. 4. The mobile phone confirms that pairing has completed and the SPH10S is ready to use. You will hear a voice prompt from the SPH10S saying “Your headset is paired”. 5. If the pairing process is not completed within three minutes, the SPH10S will return to stand-by mode. 6.2 Bluetooth Stereo Device Pairing 1.
SPH10S If you have a MP3 stereo music phone such as a smartphone, sometimes you may need to selectively use the SPH10S for A2DP stereo music only or for mobile phone handsfree only. This instruction is for advanced users who want to pair the SPH10S to their smart phones only with one selective profile: A2DP stereo for music or HFP for phone call. If you have previously paired a mobile phone to the SPH10S, you must clear the previous paring list on both devices; the mobile phone and SPH10S.
SPH10S A 8. INTERCOM PAIRING B 8.1 Pairing with Other SPH10S Headsets for Intercom Conversation The SPH10S can be paired with up to three other headsets for Bluetooth intercom conversation. 1. Turn on the two SPH10S headsets (A and B) that you would like to pair with each other. 2. Press and hold the Jog Dial of the headset A and B for 5 seconds until red LEDs of the both units start to flash rapidly. You will hear a voice prompt saying “Intercom pairing”. 3.
SPH10S Note: For example, after the pairing procedures listed above, headset D is the first intercom friend of headset A. Headset C is the second intercom friend of headset A, and headset B is the third intercom friend of headset A. 8.2 Pairing with Other Sena Headset Models for Intercom Conversation The SPH10S can be paired with all other Sena headset models such as the SMH10 and the SPH10 for intercom conversation. Please follow the same procedure as above to pair with these headset models.
SPH10S The voice prompt for each menu item is as below: (1) VOX phone (2) VOX intercom (3) Voice prompt (4) PLC setting (5) Delete all pairings (6) Exit configuration 9.2 Enabling/Disabling Voice Activated Intercom VOX phone Exit configuration VOX intercom Delete all pairings Voice prompt PLC setting 9.
SPH10S 9.3 Enabling/Disabling Voice Prompts Voice Prompt “Voice prompt” Factory Default Enable Enable Tap the Phone Button Disable Tap the Jog Dial You can disable voice prompts by configuration setting, but the following voice prompts are always on. - Voice prompts for configuration setting menu - Voice prompts for battery level Indicator - Voice prompts for factory reset 9.
SPH10S Taping the Jog Dial is not available for this setting. 9.6 Exit Voice Configuration Menu Voice Prompt “Exit configuration” Factory Default N/A Enable Tap the Phone Button To exit voice configuration menu and get back to standby mode, rotate the Jog Dial until you hear a voice prompt, “Exit configuration”, and tap the Phone Button to confirm. Taping the Jog Dial is not available for this setting.
SPH10S You can listen to stereo music in two ways: with the enclosed stereo audio cable or by Bluetooth wireless stereo. 11.1 By Stereo Audio Cable Plug your stereo MP3 player directly to the SPH10S by using the enclosed 3.5mm stereo audio jack cable. To adjust the volume, rotate the Jog Dial on the headset. You may adjust the volume on the MP3 player also. 2. To play or pause music, press and hold the Jog Dial for 1 second until you hear a double beep. MP3 Jack 11.
SPH10S 3. To track forward or track back, rotate while pressing the Jog Dial clockwise or counter clockwise. Note: Bluetooth music is available only when the MP3 jack port remains open. Please make sure the audio cable is unplugged from the clamp unit to play music by Bluetooth. 16 12. MOBILE PHONE CALL MAKING AND ANSWERING 1. When you have an incoming call, simply tap the Phone Button or the Jog Dial to answer the call. 2.
SPH10S Answer Tap Phone Button or Tap Jog Dial or Say “Hello” End Tap Phone Button or Press Jog Dial for 2” Reject Press Jog Dial for 2” Transfer Press Phone Button for 2” Call Use phone keypad Redial 13. TWO-WAY INTERCOM English the mobile phone keypad. - Tap the Phone Button in stand-by mode to activate the voice dialing of your mobile phone. For this, the voice dialing feature must be available on the mobile phone. Refer to your mobile phone manual for further instruction.
SPH10S tapping. A double or triple tapping will do nothing in this case. Terminate End Two-way Intercom Conversation Start intercom End intercom 1st intercom friend 2nd intercom friend 3rd intercom friend Single tap Double tap Triple tap Single tap Start & End Two-way Intercom 13.2 Intercom and Mobile Phone Call 1. When you have an incoming mobile phone call during an intercom conversation, you will hear a ring tone.
SPH10S 14.1 Start Three-way Intercom rin First Friend (B) Second Friend (C) 3. The second intercom friend (C) may join the intercom by making an intercom call to you (A). (A) First Friend (B) Second Friend (C) g Pa i (A) rin First Friend (B) (A) i Pa g You (A) can have a three-way conference intercom with two other SPH10S friends (B & C) by establishing two intercom connections at the same time.
SPH10S 4. Now you (A) and two SPH10S intercom friends (B & C) are having a three-way conference intercom. However, you still have the intercom connection with your second intercom friend (C). Jog Dial Operation Press for 1” (A) First Friend (B) Second Friend (C) 14.2 End Three-way Intercom When you are a member of an active three-way conference intercom, you can completely terminate the conference intercom or just disconnect an intercom connection with one of your active intercom friends. 1.
SPH10S 15.1 Start Four-way Intercom You can have four-way conference intercom with three other SPH10S users by adding one more intercom participant to the three-way intercom. While you are having three-way intercom as above in section 14.1, a new participant (D), who is an intercom friend of your intercom friend (C), may join the conference intercom by making an intercom call to your intercom friend (C). Please note that in this case, the new participant (D) is an intercom friend of (C), not of you (A).
SPH10S 16. THREE-WAY CONFERENCE PHONE CALL WITH INTERCOM PARTICIPANT You can have a three-way conference phone call by adding an intercom friend to the mobile phone conversation. While having a mobile phone call, make an intercom call to one of the intercom friends by tapping the Jog Dial to form a three-way conference call with the person on the mobile phone line. To disconnect the intercom first and go back to your private mobile phone call, terminate the intercom by tapping the Jog Dial.
SPH10S 1. To restore the SPH10S to factory default settings, press and hold the Phone Button for 12 seconds until the LED shows solid red and you hear double beeps. You will hear a voice prompt saying “Factory reset”. 2. Within 5 seconds, press the Jog Dial to confirm reset. The headset will be restored to factory setting and switched off automatically. You will hear a voice prompt saying “Headset reset, good-bye”. 3.
SPH10S 2. Turn the set-screw to the left to take the module apart from the ear flap. 3. Take out the module from the front of the ear flap to see the reset pin-hole on the opposite side of the module. Detach 4. Insert a paper clip into the reset pin-hole and press the reset button for 1 second with light pressure, at which time the SPH10S will be switched off. Turn the SPH10S back on. By powering back on, this will restore your current settings. 24 21.
SPH10S Case 2 Case 1 • iPhone for mobile phone call and stereo music streaming •SPH10S for two-way intercom •Feature phone for mobile phone call •iPod Touch for stereo music streaming • Two other SPH10Ss for three-way conference intercom English 22. CASE STUDY Feature Phone Mobile Pairing: 6.1 Call iPhone Intercom Conversation Mobile Call Pairing: 6.1 Music SPH10S Intercom Conversation SPH10S Pairing: 8.1 Pairing: 8.1 Music SPH10S Pairing: 6.2 iPod Touch Intercom Conversation Pairing: 8.
SPH10S BATTERY INFORMATION MAINTENANCE AND CARE The SPH10S has an internal, non-removable, rechargeable battery. Do not attempt to remove the battery from the device as you may damage the device. The battery can be charged and discharged hundreds of times, but it will eventually wear out. Recharge the battery only with Sena approved chargers designated for this device. Use of an unapproved charger may present a risk of fire, explosion, leakage, or other hazard.
SPH10S DISPOSAL The crossed-out wheel bin symbol on the product, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies to the European Union and other locations where separate collection systems are available.
SPH10S CERTIFICATION AND SAFETY APPROVALS FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. •T his device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
SPH10S Bluetooth License This product is CE marked according to the provisions of the R&TTE Directive (99/5/EC). Hereby, Sena declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. For further information please consult http://www.senabluetooth.com. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license.
SPH10S WAIVER AND GENERAL RELEASE By using the SPH10S you waive all substantial legal rights including the right to sue. Please read the following carefully before using the device. If you do not accept all terms of this agreement, you should immediately return the product for a full refund. By using the headset you agree to be bound to this agreement and forfeit the right to sue.
SPH10S before or during the use of the Device. 4.
SPH10S Two-Year Limited Warranty Sena Technologies, Inc. (“Sena”) warrants that this product (“Product”) shall conform to and perform in accordance with published technical specifications and the accompanying written materials, and shall be free of defects in materials and workmanship, for a period of two (2) year from the date of purchase by the first consumer purchaser of the Product.
SPH10S Return for Full Refund IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDITIONS, YOU MAY RETURN THIS DEVICE TO SENA FOR A FULL REFUND, PROVIDED THAT YOU DO SO NO LATER THAN 14 BUSINESS DAYS FOLLOWING THE PURCHASE OF THE DEVICE AND SUBJECT TO THE WRAPPING BEING INTACT. WHEN DOING SO, PLEASE REFER TO THIS SECTION.
2.0.0 www.senabluetooth.com User's Guide for Firmware v4.
