SMH5 FM Bluetooth® Headset & Intercom with built-in FM tuner for Scooters and Motorcycles www.SenaBluetooth.
SMH5-FM Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. SMH10™, SMH10R™, SMH5™, SMH5FM™, SMH3™, SPH10™, SPH10H™, SPH10H-FM™, SPH10S™, SR10™, SR10i™, SM10™ are trademarks of Sena Technologies, Inc. or its subsidiaries. These trademarks may not be used without the express permission of Sena. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license.
SMH5-FM CONTENTS 1. INTRODUCTION....................................................................................................................5 2. PACKAGE CONTENTS.........................................................................................................6 3. INSTALLING THE SMH5-FM ON YOUR HELMET..........................................................................7 4. POWERING ON/OFF AND CHARGING..............................................................................10 4.1 4.
SMH5-FM Thank you for choosing the Sena SMH5-FM, Bluetooth Stereo Headset and Intercom for scooters and motorcycles. With the SMH5FM, you can call handsfree on your Bluetooth mobile phone, listen to stereo music or voice instructions of GPS navigation by Bluetooth wirelessly, and have intercom conversations in full duplex with a passenger or other riders. The SMH5-FM is compliant with the Bluetooth Specification 3.
SMH5-FM 2.
SMH5-FM - Full-face Helmet Kit English 3. INSTALLING THE SMH5-FM ON YOUR HELMET ∙ Wired Microphone ∙ Velcro Pads for Wired Microphone 1. Loosen the two screws on the back plate of the clamp using the enclosed Allen Wrench. Insert the back plate of the clamp unit between the internal padding and external shell of the helmet, and tighten the two screws.
SMH5-FM 2. Attach the headset main unit to the clamp. Insert the main unit in the clamp until you feel the click that signals a secure attachment. 3. If you have any problem mounting the clamp unit on the helmet for any reason, you may use the glued surface mounting plate which can be attached to the external surface of the helmet. ocate a proper surface on the helmet to attach the unit, clean •L the helmet surface location with a moistened towel, and allow to dry thoroughly.
SMH5-FM 6. When you use the boom microphone included in the “Basic Kit”, please make sure that the fin side of the microphone is facing outward; away from your lips. You can easily recognize it by touching the fin with your fingers. English You can use the enclosed velcro pad and holder for the boom microphone to ensure secure placement.
SMH5-FM Note: Insert the speaker cable connector into the main unit and push the connector cover down to lock the connector in place. 4. POWERING ON/OFF AND CHARGING To power on and off the headset, you don’t need to press and hold any button for several seconds. Just short press the Jog Dial and the Phone Button simultaneously, and you will get quick on-and-off convenience. 4.1 Powering On Press the Jog Dial and the Phone Button at the same time for about 1 second to power on.
SMH5-FM 5. CHECKING THE BATTERY LEVEL You can check the battery level in two different ways when the headset is powering on. 5.1 LED Indicator When the headset is powering on, the red LED flashes rapidly indicating the battery level. 4 flashes = High, 70~100% 3 flashes = Medium, 30~70% 2 flashes = Low, 0~30% 4.4 Low Battery Warning 5.
SMH5-FM 6. PAIRING THE SMH5-FM WITH BLUETOOTH DEVICES Before using the SMH5-FM Bluetooth headset with any of Bluetooth devices for the first time, you need to do the pairing operation. It can be paired with Bluetooth mobile phones, Bluetooth stereo devices such as MP3, or motorcycle specific Bluetooth GPS, and with other Sena Bluetooth headsets.
SMH5-FM 6.2 Bluetooth Stereo Device Pairing 1. If the Bluetooth stereo device is integrated with the mobile phone such as smartphones, you don’t need to pair the SMH5-FM with it separately. When the SMH5-FM is paired with the mobile phone, it is also paired as a stereo music device. 2. If you have a stand alone Bluetooth stereo device, follow the pairing procedure separately. The procedure is the same as the procedure of “6.1 Mobile phone pairing”. Note: 1.
SMH5-FM 5. The GPS confirms that pairing has completed and the SMH5-FM is ready to use. You will hear a voice prompt from the SMH5-FM saying “Your headset is paired”. 6. If the pairing process is not completed within three minutes, the SMH5-FM will return to stand-by mode. The pairing diagram for multipoint GPS pairing is shown in the figure below. 6.3.
SMH5-FM If you have a MP3 stereo music phone such as a smartphone, sometimes you may need to selectively use the SMH5-FM for A2DP stereo music only or for mobile phone handsfree only. This instruction is for advanced users who want to pair the SMH5-FM to their smartphones only with one selective profile: A2DP for stereo music or HFP for phone call. If you have previously paired a mobile phone to the SMH5-FM, you must clear the previous paring list on both devices; the mobile phone and SMH5-FM.
SMH5-FM A 8. PAIRING WITH OTHER SMH5-FM HEADSETS FOR INTERCOM CONVERSATION The SMH5-FM can be paired with up to three other headsets for Bluetooth Intercom conversation. 1. Turn on the two SMH5-FM headsets (A and B) that you would like to pair with each other. 2. Press and hold the Jog Dial of the headset A and B for 5 seconds until red LEDs of the both units start to flash rapidly. You will hear a voice prompt saying “Intercom pairing”. 3.
SMH5-FM Note: For example, after the pairing procedures listed above, headset D is the first intercom friend of headset A. Headset C is the second intercom friend of headset A, and headset B is the third intercom friend of headset 9. PAIRING WITH OTHER SENA HEADSET MODELS FOR INTERCOM CONVERSATION English 5. The intercom pairing queue is ‘Last-Come, First-Served’. If a headset has multiple paired headsets for intercom conversations, the last paired headset is set as first intercom friend.
SMH5-FM 10. SMH5-FM CONFIGURATION SETTING You can set the configuration of the SMH5-FM by the voice menu instruction as below. 1. To enter into voice configuration menu, press and hold the Jog Dial for 12 seconds until the LED shows solid blue and you hear high tone double beeps. You will also hear a voice prompt saying “Configuration menu”. 2. Rotate the Jog Dial clockwise or counter-clockwise to navigate between the menus. You will hear voice prompts for each menu items as below. 3.
SMH5-FM Note: 1. A fter assigning a phone number to one of three speed dials, you can continually assign another phone number to the rest of two speed dials. 2. You can assign phone numbers to speed dials in your PC. Please visit the Sena Bluetooth web site at www.SenaBluetooth.com for more information. 10.2 Enabling/Disabling RDS AF English 2. Tap the Phone Button, and you will hear a voice prompt saying “Speed dial one” and “Phone connected”. 3.
SMH5-FM 10.3 Enabling/Disabling Voice Activated Phone Answering Voice Prompt 10.4 Enabling/Disabling Voice Prompts “VOX phone” Voice Prompt Factory Default Enable Factory Default Enable Enable Tap the Phone Button Enable Tap the Phone Button Disable Tap the Jog Dial Disable Tap the Jog Dial If this feature is enabled, you can answer incoming calls by simply saying a word loudly enough.
SMH5-FM 10.6 Exit Voice Configuration Menu “Exit configuration” Factory Default N/A Enable Tap the Phone Button 11. USING THE SMH5-FM 11.1 Volume Adjustment RDS AF Enable Disable You can easily adjust the volume by rotating the Jog Dial. You will hear a beep when the volume reaches maximum or minimum level. The volume is set and maintained independently at different levels for each audio source even when you turn off and on the headset.
SMH5-FM 5. To transfer a call between the mobile phone and the headset during the phone conversation, press the Phone Button for 2 seconds until you hear a beep. 6. There are several ways to make a phone call: • Enter numbers on your mobile phone keypad and make a call. Then the call is automatically transferred to the headset. • For some older mobile phones which do not automatically transfer calls to the headset, press the Phone Button after entering phone numbers on the mobile phone keypad.
SMH5-FM Note: Make sure that you should connect the mobile phone and the headset in order to use the speed dial function. Answer End Tap Phone Button or Tap Jog Dial Press Jog Dial for 2” Transfer Press Phone Button for 2” Speed Dial Voice Command 1. You can start an intercom conversation with any of intercom friends by tapping the Jog Dial: single tapping to intercom with the first intercom friend, double tapping with the second intercom friend, and triple tapping with the third intercom friend.
SMH5-FM 11.5 Intercom and Mobile Phone Call 1. When you have an incoming mobile phone call during an intercom conversation, you will hear a ring tone. You can choose whether to 1) answer the mobile phone call and stop the intercom conversation, or 2) reject the phone call and stay on the intercom conversation. 2. When you have an incoming intercom call during a mobile phone call, you will hear 4 high tone beeps, alerting you that there is an incoming intercom call.
SMH5-FM 11.8 FM Radio 11.8.1 FM Radio On / Off To turn on the FM radio, press and hold the Phone Button for 2 seconds until you hear a mid-tone double beep sound. You will then hear a voice prompt saying “FM on”. In order to turn off the FM radio, press and hold the Phone Button for 2 seconds until you hear a voice prompt saying “FM off”. When you power off, the SMH5-FM will remember the last station frequency. When you power on, the last station frequency will be playing. 11.8.
SMH5-FM 11.8.4 Scan and Save “Scan” is the function that searches from the current station frequency upward for stations in a whole range of FM frequencies. To use the scan function, please follow the procedures below: 1. Double tap the Phone Button. Then the current station frequency moves upward to find other station frequencies. 2. If the tuner finds a station, it stays at the station frequency for 8 seconds, then scanning to the next station frequency. 3.
SMH5-FM 11.10 Function Priority The SMH5-FM operates in the following order of priority: (Highest) (Lowest) - To track forward or track back, rotate while pressing the Jog Dial clockwise or counter clockwise. English - To play or pause music, press and hold the Jog Dial for 1 second until you hear a double beep. Mobile Phone, Intercom, Music sharing by Bluetooth stereo music, FM Radio, Bluetooth Stereo Music A lower priority function is always interrupted by a higher priority function.
SMH5-FM 11.11 Music Sharing 11.12 Reset to Factory Default Settings You can start sharing music with an intercom friend using Bluetooth stereo music during a two-way intercom conversation. When you terminate music sharing, you can go back to the intercom conversation. To start or terminate sharing music, press and hold the Jog Dial for 1 second during an intercom conversation until you hear a double beep and you and your intercom friend will listen to or terminate sharing music.
SMH5-FM 11.13 Fault Reset 12. FIRMWARE UPGRADE English When the SMH5-FM is not working properly or is in faulty status for any reason, you may reset by pushing the pin-hole reset button at the back of the headset main unit. Insert a paper clip into the reset pin-hole and press the reset button for a second with light pressure. The SMH5-FM will be switched off after which time, you have to turn the system back on and try again. However, this will not restore the headset to factory default settings.
SMH5-FM Type 13.
SMH5-FM Type Button Duration LED Beep Seek stations (FM mode) Jog Dial Rotating while pressing Scan up FM band (FM mode) Phone Button Double tapping — — Stop scanning (FM mode) Phone Button Double tapping — High tone double beeps Save preset while scanning (FM mode) Phone Button Tapping — High tone double beeps Temporary preset (FM mode) Phone Button Triple tapping — — Jog Dial 12 sec Solid blue High tone double beeps RDS AF Setting — High tone triple beeps Rotate the Jog
SMH5-FM MAINTENANCE AND CARE DISPOSAL The Product should be treated with care and the following suggestions will help you protect your warranty coverage. 1. Do not use or store the device in dusty, dirty areas. Its moving parts and electronic components can be damaged. 2. Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and wrap or melt certain plastics. 3. Do not store the device in cold areas.
SMH5-FM FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
SMH5-FM Luxembourg, The Netherlands, Portugal, Spain, Sweden, United Kingdom and within EFTA in Iceland, Norway and Switzerland. Industry Canada Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
SMH5-FM Sena hereby notifies you that using this Device may also be in contravention to local, federal, state or national laws or regulations, and that any use of the Device is entirely at your sole risk and responsibility. 1.
SMH5-FM any losses and/or damages, whether caused in whole or in part by the negligence or other conduct of others, including the Company. 5. You confirm that you have read this release of liability and fully understand its terms and that you have given up substantial rights by not returning the Device for a full refund (see refund option below). Two-Year Limited Warranty Sena Technologies, Inc.
SMH5-FM Return for Full Refund IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDITIONS, YOU MAY RETURN THIS DEVICE TO SENA FOR A FULL REFUND, PROVIDED THAT YOU DO SO NO LATER THAN 14 BUSINESS DAYS FOLLOWING THE PURCHASE OF THE DEVICE AND SUBJECT TO THE WRAPPING BEING INTACT. WHEN DOING SO, PLEASE REFER TO THIS SECTION.
1.3.0 www.SenaBluetooth.com User's Guide for Firmware v1.
