SENA EXPAND Bluetooth® Stereo Headset & Intercom www.SenaBluetooth.
EXPAND © 1998-2013 Sena Technologies Inc. All rights reserved. Sena Technologies Inc. reserves the right to make any changes and improvements to its product without prior notice. Sena™ is a trademark of Sena Technologies Inc. or its subsidiaries in the USA and other countries. SMH10™, SMH10R™, SMH5™, SMH5-FM™, SPH10™, EXPAND™, SPH10H™, SPH10H-FM™, SPH10S™, SR10™, SR10i™, SM10™ are trademarks of Sena Technologies, Inc. or its subsidiaries.
EXPAND 1. INTRODUCTION..................................................................................4 2. PACKAGE CONTENTS.......................................................................5 3. GETTING STARTED......................................................................6 3.1 Wearing the Sena Expand .........................................................6 3.2 Installing the Microphone Windscreen........................................7 3.3 Powering On.......................................
EXPAND 1. INTRODUCTION The Sena Expand is a Bluetooth Stereo headset with long-range Bluetooth intercom designed specifically for outdoor sports activities. With the Sena Expand, you can listen to stereo music, call handsfree on their Bluetooth mobile phone, and have intercom conversations in full duplex with up to four companions. Also, the easy-to-access and intuitive headset makes the Sena Expand a perfect companion for outdoor sports. The Sena Expand is compliant with Bluetooth 3.
EXPAND English 2.
EXPAND 3. GETTING STARTED USB Power & Data Cable 3.1 Wearing the Sena Expand Proper fit on your ear and head is important both for comfort and optimal noise-reduction performance. The speaker with microphone should be placed on the left ear. Then you can place earhooks over ears and pull the microphone in toward your lips as positioning the microphone with its talk side facing in as shown below.
EXPAND 3.3 Powering On Press and hold the Center Button and the (+) Button at the same time for 1 second to power on. The blue LED turns on and you will hear ascending beeps and “Hello”. 3.4 Powering Off Press the Center Button and the (+) Button simultaneously (you don’t need to press and hold in order for the system to power off). The red LED turns on for about 2 seconds until it turns off completely and you will hear “Goodbye” and descending beeps. 3.
EXPAND 3.6 Function Priority The Sena Expand operates in the following order of priority: (highest) Mobile phone, Intercom, Music sharing by Bluetooth stereo music, (lowest) Bluetooth stereo music A lower priority function is always interrupted by a higher priority function. For example, stereo music is interrupted by an intercom call, and intercom conversation is interrupted by an incoming mobile phone call. 8 3.
EXPAND 3.9 Checking the Battery Level You can check the battery level in two different ways when the headset is powering on. 3.10 Fault Reset When the Sena Expand is not working properly or is faulty for any reason, you may reset it by pushing the pinhole reset button at the back of the headset main unit. 1. Rotate the speaker pad of the left headset counterclockwise to detach it. 3.9.1 LED Indicator When the headset is powering on, the red LED flashes rapidly indicating the battery level.
EXPAND 2. Insert a paper clip into the reset pin-hole and press the reset button for a second using light pressure. The Sena Expand will be switched off, and you have to turn the system back on and try again. However, this will not restore the headset to the factory default settings. 4.
EXPAND Bluetooth Pairing (Phone, MP3) 1) 10 sec 2) English Intercom Pairing (Compatible with all Sena headsets) 1 press pairing B A 1) 5 sec 5 sec 3) Select Sena EXPAND Sena EXPAND v1.0 Sena EXPAND v1.
EXPAND Mobile Phone 2 sec 1 press Reject Answer Music 2 sec 1 sec End 3 sec 1 sec Voice Command 3 sec 12 1 sec
EXPAND You can set the configuration of the Sena Expand by the voice menu instructions as below. 1. To enter the voice configuration menu, press and hold the Center Button for 10 seconds until the LED shows solid blue and you hear high tone double beeps. You will also hear the voice prompt, “Configuration menu”. 2. Press the (+) Button or (-) Button to navigate between the menus. You will hear voice prompts for each menu item as below. 3.
EXPAND 5.2 Multipoint Pairing Voice Prompt “Multipoint pairing” Factory Default N/A To go into multipoint pairing mode, press the (+) Button or the (-) Button until you hear the voice prompt, “Multipoint pairing”. Please refer to section 6.2 for details on multipoint pairing. If you press the (+) or (-) Button, you can exit from the multipoint pairing mode. 5.
EXPAND Note: 1. A fter assigning a phone number to one of three speed dials, you can continually assign another phone number to the rest of two speed dials. 2. You can assign phone numbers to speed dials in your PC. Please visit the Sena Bluetooth web site at www. SenaBluetooth.com for more information. 5.
EXPAND 5.9 Exit Voice Configuration Menu Voice Prompt “Exit configuration” Factory Default N/A Execute Press the Center Button To exit voice configuration menu and get back to stand-by mode, press the (+) Button or (-) Button until you hear the voice prompt, “Exit configuration”. Press the Center Button to confirm.
EXPAND 6.2 Multipoint Pairing Typical Bluetooth headsets can connect with only one HFP (Hands-Free Profile) device, but multipoint pairing allows the headset to connect with two HFP devices at the same time. So, when you already have a mobile phone connected with the Sena Expand, you can also pair and connect a second mobile phone or other HFP device such as the Sena SR10, Bluetooth adapter. 1.
EXPAND 6.3 Bluetooth Stereo Device Pairing If the Bluetooth stereo device is integrated with a mobile phone such as a smartphone, you don’t need to pair the Sena Expand with it separately. When the Sena Expand is paired with the mobile phone, it is also paired as a stereo music device. If you have a stand alone Bluetooth stereo device, follow the pairing procedure separately. The procedure is the same as the procedure given in “5.1 Mobile Phone Pairing”. Note: 1.
EXPAND Mobile Phone Two-way Radio HFP + A2DP Mobile Phone Pairing HFP Multipoint Pairing SR10 Parallel Connection of SR10 and Mobile Phone by Bluetooth Multipoint Pairing If you have a MP3 stereo music phone such as a smartphone, sometimes you may need to selectively use the Sena Expand for A2DP stereo music only or for mobile phone handsfree only.
EXPAND 7.1 Phone Selective Pairing: HFP for Phone Call Only 1. To enter the voice configuration menu, press and hold the Center Button for 10 seconds until you hear the voice prompt, “Configuration menu”. 2. Press the (+) Button three times and you will hear the voice prompt, “Phone selective pairing”. 3. Search for Bluetooth devices on your smartphone. Select Sena Expand in the list of devices detected on your phone. 4. Enter 0000 for the PIN. Some smart phones may not ask for a PIN. 7.
EXPAND 9.1 Mobile Phone Call Making and Answering 1. When you have an incoming call, press the Center Button to answer the call. 2. To end a call, press and hold the Center Button for 2 seconds until you hear a mid-tone single beep, or wait for the called person to end the call. 3. To reject a call, press and hold the Center Button for 2 seconds until you hear a beep while the phone is ringing. 4. There are several ways to make a phone call: - Enter numbers on your mobile phone keypad and make a call.
EXPAND 3. Tap the Center Button to select a voice menu among the followings: (1) Last number redial (2) Speed dial 1 (3) Speed dial 2 (4) Speed dial 3 (5) Cancel 4. After selecting the last number redial menu, you will hear a voice prompt, “Last number redial”. Then, to redial the last phone call number, tap the Center Button. 5. To call one of the speed dials, tap the (+) Button or the (-) Button to navigate between the menus until you hear a voice prompt, “Speed dial (#)”. Then, tap the Center Button.
EXPAND A English 10. INTERCOM B D 10.1 Pairing with Other Sena Expand Headsets for Intercom Conversation The Sena Expand can be paired with up to three other headsets for Bluetooth intercom conversation. 1. Turn on the two Sena Expand headsets (A and B) that you would like to pair with each other. 2. Press and hold the Center Button for 5 seconds, then you will hear a mid-tone single beep and the voice prompt, “Intercom pairing”. 3.
EXPAND 5. The intercom pairing queue is ‘Last-Come, FirstServed’. If a headset has multiple paired headsets for intercom conversations, the last paired headset is set as the first intercom friend. The previous intercom friend becomes the second intercom friend, and third intercom friend. Note: For example, after the pairing procedures listed above, headset D is the first intercom friend of headset A.
EXPAND 2. When you have an incoming intercom call during a mobile phone call, you will hear 4 high tone beeps, alerting you that there is an incoming intercom call. You will also hear the voice prompt, “Intercom requested”. In this case, the intercom call does not override the mobile phone call because intercom has a lower priority than a mobile call. You have to hang up the mobile phone call to make or receive an intercom call. 10.3.3 Intercom and Two-way Radio As described in 6.
EXPAND Mobile Phone Two-way Radio HFP + A2DP Mobile Phone Pairing Wired Connection Audio from Two-way Radio Sena Expand Multipoint Pairing SR10 Intercom Intercom Pairing 10.4 Three-way Intercom 10.4.1 Start Three-way Intercom You (A) can have a three-way conference intercom with two other Sena Expand friends (B & C) by establishing two intercom connections at the same time.
EXPAND 4. Now you (A) and two Sena Expand intercom friends (B & C) are having a three-way conference intercom. (A) ng ri i Pa (A) First Friend (B) First Friend (B) Second Friend (C) 3. The second intercom friend (C) may join the intercom by making an intercom call to you (A). (A) First Friend (B) Second Friend (C) Second Friend (C) 10.4.
EXPAND intercom connection with your second intercom friend (C). To disconnect from intercom friend (C), press twice the Center Button. Now both intercom friends are disconnected. Center Button Press and hold for 1" Result Disconnect (B) & (C) Press once Disconnect (B) Press twice Disconnect (C) End Three-way Intercom 10.4.3 T hree-way conference phone call with intercom participants You can have a three-way conference phone call by adding an intercom friend to the mobile phone conversation.
EXPAND You (A) First Friend (B) New Participant (D) = Intercom Friend of (C) Second Friend (C) 10.5.2 End Four-way Intercom As in the case of three-way intercom, you can completely exit from the four-way conference intercom or just disconnect a single intercom connection. 1. Press and hold the Center Button for 1 second until you hear a beep to terminate four-way conference intercom. It terminates the intercom connections between you (A), and your intercom friends (B) and (C). 2.
EXPAND 10.6 Intercom Failure When you try to start an intercom conversation with an intercom friend who is already having a conference intercom with other riders or is on a mobile phone call, you will hear a low tone double beep signifying that the intercom is busy. In this case, you have to try again later. 10.7 Intercom Reconnection If your intercom friend goes out of range while having an intercom conversation, you may hear static and eventually the intercom will be disconnected.
EXPAND The Sena Expand supports a firmware upgrade function. Please visit the Sena Bluetooth web site at www.SenaBluetooth.com to check the latest software downloads. 13. SENA BLUETOOTH CONNECTION CASE STUDIES English 12.
EXPAND Case 2 • Mobile phone calls • MP3 Player for stereo music streaming • Two other Sena Expand for three-way conference intercom Case 3 • Mobile phone calls and stereo music streaming • Sena SR10 for two-way radio and radar detector alarm • Sena Expand for two-way intercom Mobile Phone Mobile Phone Two-way radio Mobile Phone Pairing Mobile Phone Pairing Intercom Pairing 32 Tow-way radio Mobile Phone Pairing Intercom Pairing Wired Connection Multipoint Pairing Intercom Pairing SR10
EXPAND Type Description LED Power-off Center Button & (+) Button 1 press Solid red Volume Adjustment (+) Button or (-) Button 1 press - Center Button 10 sec Type Sollid blue MP3 (+) Button 1 press Blue & red alternatively flashing Answer mobile phone call Center Button 1 press - End a call Center Button 2 sec - Reject an incoming call Center Button 2 sec - Voice command Center Button 3 sec - Voice dialing Center Button 3 sec - Redial last number (+) Button 3 sec -
EXPAND BATTERY INFORMATION MAINTENANCE AND CARE The product has an internal, non-removable, rechargeable battery. Do not attempt to remove the battery from the device as you may damage the device. The battery can be charged and discharged hundreds of times, but it will eventually wear out. Recharge the battery only with Sena approved chargers designated for this device. Use of an unapproved charger may present a risk of fire, explosion, leakage, or other hazard.
EXPAND The crossed-out wheel bin symbol on the product, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies to the European Union and other locations where separate collection systems are available.
EXPAND • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC RF Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
EXPAND The Sena Expand is compliant with and adopts the Bluetooth® Specification 3.0 and has successfully passed all interoperability tests that are specified in the Bluetooth® specification. However, interoperability between the device and other Bluetooth®-enabled products is not guaranteed. WAIVER AND GENERAL RELEASE By using the product you waive all substantial legal rights including the right to sue. Please read the following carefully before using the device.
EXPAND to address its technical capabilities and should not be misconstrued as if encouraging users to operate the Device while actively involved in traffic.
EXPAND Two-Year Limited Warranty Sena Technologies, Inc. (“Sena”) warrants that this product (“Product”) shall conform to and perform in accordance with published technical specifications and the accompanying written materials, and shall be free of defects in materials and workmanship, for a period of two (2) year from the date of purchase by the first consumer purchaser of the Product.
EXPAND Limitation of Liability EXCEPT AS EXPRESSLY PROVIDED HEREIN, SENA MAKES NO WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED, WITH RESPECT TO ANY EQUIPMENT, PARTS OR SERVICES PROVIDED PURSUANT TO THIS AGREEMENT, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
EXPAND English WARNING Sena informs that using this device in public traffic may not be authorized by the law. Please check your local law and use this device only out of public traffic such as private properties or closed circuits. If the simultaneous use of both ear speakers while riding a motorcycle is prohibited by your local law, please use only a single ear speaker while riding. Sena denies any liability should you choose not to respect this warning.
1.0.0 www.SenaBluetooth.com User's Guide for Firmware v1.
