Sena Bluetooth Pack for GoPro® User's Guide
© 1998-2014 Sena Technologies Inc. All rights reserved. Sena Technologies Inc. reserves the right to make any changes and improvements to its product without prior notice. GoPro® is a registered trademark of Woodman Labs of San Mateo, California. Sena Technologies, Inc. (“Sena”) is not affiliated with Woodman Labs. The Sena Bluetooth Pack for GoPro® is an aftermarket accessory specially designed and manufactured by Sena Technologies, Inc. for the GoPro® Hero3 allowing for Bluetooth capabilities.
1. INTRODUCTION...............................................4 2. PACKAGE CONTENTS......................................5 Bluetooth Pack......................................................................5 Audio Connector..................................................................5 Frame Case.............................................................................5 3. GETTING STARTED...........................................6 Attaching the Bluetooth Pack to the GoPro®.............
1. INTRODUCTION Thank you for choosing the Sena Bluetooth Pack for GoPro®. The Sena Bluetooth Pack for GoPro® is a specially designed adapter for the GoPro® Hero3 and Hero3+ allowing for Bluetooth capabilities. With the use of Bluetooth headsets, the Sena Bluetooth Pack for GoPro® allows users to add their voice to the video on-the-fly using the Bluetooth Audio Recording™ feature.
English 2.
3. GETTING STARTED Attaching the Bluetooth Pack to the GoPro® 1 Slide the hooked end of the Bluetooth Pack into the groove on the right side of the camera body. 2 Push the Bluetooth Pack into the GoPro® bus port on the back of the camera. 1 2 6 3 Connect the GoPro® to Bluetooth Pack with the Audio Connector.
1 2 Pull back on left side of the Bluetooth Pack to disconnect from the GoPro® bus port. 3 Slide the hooked end of the Bluetooth Pack out of camera groove. English Removing the Bluetooth Pack from the GoPro® Remove the Audio Connector.
Installing the Case 1 Align the Audio Connector with the space on the frame. 2 Lift up the frame case slightly and slide the assembled camera into the frame case. Make sure to align the camera with the edges firmly.
You can mount the assembled frame case to helmets, vehicles, and other gears by using the GoPro® accessories: Attachment Buckle and Thumb Screw (sold separately). Powering On Push the Power Switch down to power on, then the LED will flash blue. Powering Off Push the Power Switch upward to power off, then the LED will turn red and automatically be turned off shortly.
Power Switch Off Mic Switch Audio Source Off None On Internal microphone of the Bluetooth Pack Off Microphone of Bluetooth headset On Internal microphone of the Bluetooth Pack + microphone of Bluetooth headset On the USB cable supplied in the GoPro® to charge the Bluetooth Pack. The LED turns red while charging, and turns blue when the Bluetooth Pack is fully charged. It takes about 2.5 hours to fully charge.
Status 4 flashes High, 70 to 100 % remaining battery 3 flashes Medium, 30 to 70 % remaining battery 2 flashes Low, 0 to 30 % remaining battery Press the Pairing Button 3 times, you can check the battery level with voice prompts from a connected headset. Fault Reset English LED When the Bluetooth Pack is not working properly or is in faulty status for any reason, you can reset the Bluetooth Pack.
Factory Reset Through the factory reset, you can restore the factory default settings of the Bluetooth Pack. Then all of the previous pairing information is deleted. 1 2 12 Press and hold the Pairing Button for 10 seconds to enter the factory reset mode. Then the LED will turn red and you can hear the voice prompts from the connected headset. Press the Pairing Button again to reset the Bluetooth Pack. 10 sec.
Headset Audio Recording Mode English 4.
Pairing with Headsets For Sena Headsets To record your voice to the GoPro® by using the Bluetooth Pack, you should pair the Bluetooth Pack with a Bluetooth headset (or microphone). This pairing operation is only required once for each Bluetooth headset. 1 Press and hold the Pairing Button of the Bluetooth Pack for 5 seconds until the LED flashes red and blue alternately. 2 Enter into the intercom pairing mode of the headset. Then the headset is paired automatically with the Bluetooth Pack.
Start Recording 1 Press and hold the Pairing Button of the Bluetooth Pack for 5 seconds until the LED flashes red and blue alternately. 2 Enter into the handsfree pairing mode of the non-Sena headset. For details on handsfree pairing, refer to the user’s guide of the corresponding headset. 3 When the LED flashes blue, the pairing is completed. Then you will hear the voice prompt saying “GoPro Pack connected” from the connected corresponding headset.
For Sena Headsets You can connect the Bluetooth Pack with Sena headsets and transfer the conversations to the Bluetooth Pack by establishing intercom connections at the same time. 1 2 Turn on the paired Sena headset, and then the Bluetooth Pack is automatically connected to the paired headsets. The audio channel between the Bluetooth Pack and the Sena headset is open. Then the status LED of the Bluetooth Pack flashes blue. Start recording on the GoPro®.
Bluetooth Pack (A) Turn on the paired non-Sena headset, and then the Bluetooth Pack is automatically connected to the headset. The audio channel between the Bluetooth Pack and the non-Sena headset is open. Then the status LED of the Bluetooth Pack flashes blue. 2 Start recording on the GoPro®.
Ultra HD Voice Recording™ Mode & Normal Voice Recording Mode Enabling the Ultra HD Voice Recording™ Mode When using a Sena headset, Ultra HD Voice Recording™ is supported; it enables you to record your voice in CD-quality with live ambient sound. Ultra HD Voice Recording™ is available only when a single Sena headset is connected with the Bluetooth Pack. It is not supported in conference intercom mode.
Bluetooth Audio Mix When using a Sena Headset, you can enable or disable the sidetone function while the audio channel between the Bluetooth Pack and the headset is open. When the sidetone function is enabled, you can hear your own voice echoed from the Bluetooth Pack through the headset. When you turn on the Mic Switch, the internal stereo microphones are activated; the Bluetooth Pack transmits the mixed audio signals from the Bluetooth Pack’s internal microphones and the connected headset to the GoPro®.
Firmware Upgrade The Bluetooth Pack supports firmware upgrade function. Please visit Sena Bluetooth web site at www.SenaBluetooth.com to check the latest software downloads.
Type Operation Button Duration LED Power on Power Switch Pushing down Solid blue Power off Power Switch Pushing upward Solid red 5 sec Blue & red alternatively flashing Basic Function Headset pairing Pairing Button Pairing English 5.
6. SPECIFICATIONS Talk time 3 hours Stand-by time 3 days General Battery Charging time Type Operating temperature -10˚C ~ 55˚C (14°F ~ 131°F) General Dimensions (main module) Weight Working distance 22 59 mm x 41 mm x 16.6 mm (2.3 inch x 1.6 inch x 0.6 inch) Lithium polymer battery Version Bluetooth 3.0 Profile Headset Profile (HSP), Hands-Free Profile (HFP) Bluetooth 21g 2.
MAINTENANCE AND CARE The product has an internal, non-removable, rechargeable battery. Do not attempt to remove the battery from the device as you may damage the device. The battery can be charged and discharged hundreds of times, but it will eventually wear out. Recharge the battery only with Sena approved chargers designated for this device. Use of an unapproved charger may present a risk of fire, explosion, leakage, or other hazard.
DISPOSAL The crossed-out wheel bin symbol on the product, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies to the European Union and other locations where separate collection systems are available.
FCC Caution • Reorient or relocate the receiving antenna. Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment. • Increase the separation between the equipment and CE Declaration of Conformity receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Statement Two-Year Limited Warranty This device complies with Industry Canada licenseexempt RSS standard(s). Sena Technologies, Inc. (“Sena”) warrants that this product (“Product”) shall conform to and perform in accordance with published technical specifications and the accompanying written materials, and shall be free of defects in materials and workmanship, for a period of two (2) year from the date of purchase by the first consumer purchaser of the Product.
Limitation of Liability EXCEPT AS EXPRESSLY PROVIDED HEREIN, SENA MAKES NO WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED, WITH RESPECT TO ANY EQUIPMENT, PARTS OR SERVICES PROVIDED PURSUANT TO THIS AGREEMENT, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
1.0.0 www.SenaBluetooth.com User's Guide for Firmware v1.
