Bluetooth and Wi-Fi enabled Portable DVR Professional Version: SG-1000/ SG-2000/ SG-3000 MANUAL *EXCEPT FOR SECURITY PURPOSE, DO NOT USE THIS PRODUCT FOR ANY OTHER PURPOSES WHICH MAY DISTURB PRIVATE LIFE OF OTHERS. THIS PRODUCT IS REGISTERED WITH ELECTROMAGNETIC WAVE STANDARDS AND CAN BE USED FOR ANY PLACE INCLUDING RESIDENTIAL AREA. BEFORE USING THIS PRODUCT, BE SURE TO READ THE PRECAUTIONS CONTAINED IN THE MANUAL.
Unpacking Check to make sure that all of the items shown below are included with your SelfGuard. If something is missing, contact your dealer as soon as possible.
– Contents – INTRODUCTION ----------------------------------------------------------------------------------- 6 1. Precautions 6 2. Features --------------------------------------------------------------------------------------- ------------------------------------------------------------------------------------------- 11 3. Specifications and Comparison of each Model 4.
-6. Sensor Set 4-7. USB Set ------------------------------------------------------------------------------- 63 ---------------------------------------------------------------------------------- 65 4-8. MEMORY Set 4-9.Others --------------------------------------------------------------------------- 67 -------------------------------------------------------------------------------------- 70 4-9-1. Password Set --------------------------------------------------------------------- 71 4-9-2.
<< Copyright Restrictions >> Except for the security purpose, unauthorized copy, reproduction and circulation of snapshot or movie files violate copyright and international contract laws. Distribution to third parties of such files over the Internet without permission of the copyright holder, whether or not for profit violates international contract law and strictly prohibited. << Important Notice >> 9 The contents of this manual are subject to change without notice. 9 STARNEX CO., LTD.
INTRODUCTION 1. Precautions General Notice ¾ The AC/DC adaptor of this product can be used for both 110V and 220V. ¾ Never try to open the case of the Self-Guard or attempt your own repairs. High-voltage internal components create the risk of electric shock when exposed. Always leave maintenance and repair work up to a STARNEX authorized service center. ¾ Never look at the sun or other bright light through the LCD screen. Doing so can damage your eyesight.
Guard. Never use any other AC/DC adaptor besides the one that comes with this Self-Guard. ¾ Never cover the AC/DC adaptor with a quilt, blanket, or other cover while it is in use, and do not use it near a heater. ¾ At least once a year, unplug the AC/DC adaptor power cord from the power outlet and clean the area around the prongs of the plug. Dust build up around the prongs can create the risk of fire.
Data Error Precautions Your Self-Guard is manufactured using precision digital components. Any of the following creates the risk of corruption of data in file memory. ¾ Removing the battery, flash memory card, or USB memory device while the Self-Guard is performing a record or memory access operation. ¾ Disconnecting the USB cable, removing the Self-Guard from the Docking Station, or disconnecting the AC/DC adaptor from the Docking Station while a data communication operation is being performed.
then you must exit from “RECORD” or “SEARCH” mode, before removing the memory card from the Self-Guard. AUTO (POWER) OFF Function The Self-Guard automatically turns off the power or goes into the powersavings mode if you don’t press any button for a certain amount of time (1-9 minutes). This does not indicate malfunction of the system. In “RECORD” and “TRANSMIT” modes, Self-Guard turns off only the LCD, battery status LAMP, and recording status LAMP to save the battery.
This Self-Guard is designed for use in temperatures ranging from -10℃ to +50℃ (14℉ to 122℉). Do not expose this product directly to intense sun-light or heat. Do not expose to rain or extreme humidity or dirty environment. Keep this product away from extreme vibration or any magnetic devices. Only use the battery and adaptor provided by us. Do not open the cover of this product. Otherwise, the warranty will be void.
indicate malfunction. ¾ If the exterior of the Self-Guard needs cleaning, wipe it with a soft cloth. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
You can monitor any place from anywhere, because the Self-Guard transmits image and audio to remote areas using wireless transmit technology. By applying this technology, Self-Guard is the Ubiquitous security system. You can connect to the Self-Guard by the internet with a computer, and view the live images of the Self-Guard. Also, you can copy the files saved in the Self-Guard to your local computer and playback.
z Built-In (128MB) Flash Memory - Free of Data Loss, Images can be recorded without using a memory card z Memory Card for Memory Expansion z Extensive Recording Time and Data Back-up using External USB HDD or USB Memory Stick z Long Battery Life (Low-power Consumption technology for long lasting recording and playback between charges.) z File Conversion to .avi or .
3. Specifications and Comparison of each Model 3.1 Specifications SECTION Built-In Memory External Camera Built-In External DESCRIPTION 128MB Flash memory Micro SD(up to 8GB) USB Memory Stick, USB HDD 1 CMOS Color (Up to 2EA) Angle(56 Degrees), Unlimited Focus NTSC/PAL Light Sensitivity 1 Lux under@f1.
3.
4.
QUICK START GUIDE 1. Charging the Battery z Load the battery into the Self-Guard. z Plug the AC/DC adaptor directly into the power input port of Self-Guard. Or, place Self-Guard unit onto the Docking Station to charge the battery. z Total recharging time is 3 hours for a full recharge. 2. Turning the Self-Guard On and Off z Push [ENT] for 2 seconds to turn on the power. z Push [ESC] for 2 seconds and release it to turn off the power. 3.
1. Press [ENT] for 2 seconds to turn on Self-Guard. 2. Use [△] and [▽] to select “4. OPTION” and press [ENT]. 3. Use [△] and [▽] to select “4.DATE/TIME SET” and press [ENT]. 4. Use [◁] and [▷] to move the cursor to month, date, year, and time. 5. Use [△] and [▽] to change the values for each set. 6. Use [◁] and [▷] to move the cursor to “DATE TYPE”. 7. Use [△] and [▽] to select one from 3 types. (DD/MM/YY, MM/DD/YY, YY/MM/DD) 8. Press [ENT] to register the settings and exit the setting menu.
4. To record a moving image Use [△] and [▽] to select RECORD, and then press [ENT]. Then, it will appear with the sight that’s being recorded as below and the Self-Guard starts to record images. - Before you start to record, be sure to check from the LCD that the camera can capture the sight where you want it to be recorded. - Press [ESC] to stop recording and exit from the “RECORD” mode.
for camera channel numbers. If it shows C1B123, then ‘C1’ indicates of camera number 1 and ‘B123’ indicates of Bluetooth channel 1, 2 and 3. z 13:40:34: current time. z (10): elapsed recording time (10 minutes). z 39%: 39 percent of the total memory(Built-in, MICRO SD, USB) is being used for recording. 5. To Playback a Moving image Use [△] and [▽] to select “SEARCH”, and press [ENT]. Then the next screen appears as below. You can search the data either by 1.MOTION/SENSOR or 2.SENSOR.
1.MOTION/SENSOR- includes data saved by both motion and sensor detection 2.SENSOR- includes data saved by sensor detection only. Use [△] and [▽] to select “1.MOTION/SENSOR”, and then press [ENT]. Then the next screen appears as below. The list of the month and the year, which has recorded data shows on the screen. All saved data are arranged by the month and the year in a list. If there is no data saved on a month, then that specific month will not be included on the list.
• Green Colored Date: There exists saved data. • Black Colored Date: There exists no saved data. • Pink Colored Date: Cursor position Use [◁] and [▷] to select the date you want, and then press [ENT]. Then the list of saved data appears on the screen as below. To move the cursor to the options at the bottom, use [▷] and [◁].
COPY COPYALL Copy a selected file to the selected memory Copy all file of the selected date to the selected memory There are three colors (blue, red, or green) for each file to indicate which memory is used to save the file. The indications are as follow. Color of file name Meaning Blue colored file File is stored in built-in memory. Red colored file File is stored in the memory card. Green colored file File is stored in USB memory devices.
2. Select “1. CONNECT SET” 3. Select “1. BT1/CH#1/OFF” 4. “1.CONNECT: ON” 5. “4.00:02:78:0C:60:FF” ->change this ID to the SLAVE’s, which you have written down for your record in step #3 in the "SLAVE" 6. Select “1. RECORD” Please refer to the General Guide for more details about BLUETOOTH.
GETTING READY 1.
Memory Card Slot: This is the place where you put in the standard MICRO SD memory card. If you need to expand the memory from the built-in, internal memory, you can get this from where you have purchased the Self-Guard. This product provides a memory card, which lacks in memory. Cautions: Do not insert or remove the memory card from the slot while recording or searching.
sure that this hole is not blocked in order to record the audio. Battery Status & Charge Lamp: This lamp indicates how much of the battery is left. Lamp with the green color indicates that the battery is full. The color of this lamp changes into yellow when the battery is half full, and the red color means that the battery is almost used up. If you connect the AC adaptor to the Self-Guard when the battery is not full, then it automatically charges up the battery to its fullest.
external antenna (SG-942), you can increase the transmit range up to 300 meters. And the distance depends on the kind of antenna gain. Battery Holder: When you load the battery into the Self-Guard, this place keeps a hold of the battery to the Self-Guard’s body. In order to settle the battery in the Self-Guard, you need to place the battery onto the back of the Self-Guard’s body, and push the battery to the upper direction.
Guard and the computer if you connect the Self-Guard to the computer using other USB cables directly. Power Input: connector for the AC adaptor (DC 5V, 2A). 2. Docking Station LAN Port: This is the port for the LAN, where you can connect to the Self-Guard with your computer in remote places. USB Port: This is the same USB port as in the Self-Guard’s body. MIC, S1: MIC is where you put in the external microphone. S1 is the port number 1 for the sensor input and output.
and output. Provided sensor cable has three wires. The red colored wire is for S2, white colored wire is for PWR, and the striped wire is for the GND (Ground). PWR, S3: PWR is where you get the power (below 300mA) from the battery (3.6 V – 4.2 V) of the Self-Guard or from the adaptor (5 V). If the adaptor is connected to the Self- Guard, then it gets the power from the adaptor and the voltage is 5.
GENERAL GUIDE Power ON/OFF Push [ENT] for 2 seconds to turn on the power. To turn off the power, push [ESC] for 2 seconds and release it. Main Menu When you turn on the power of the Self-Guard, then a screen appears as below. I. FUNCTIONS 1.
Select “RECORD” with the direction buttons and then press [ENT]. Then it shows the screen that’s being recorded as below, and the Self-Guard starts to record images. When the Self-Guard goes into the “RECORD” mode, then the color of recording status LAMP changes into red from green. When the Self-Guard detects a motion, then the color turns into yellow. So if the Self-Guard continues to detect motions, the color alternates between red and yellow.
z 39%: 39 percent of the total memory(Built-in, MICRO SD, USB) is being used for recording. Press [▽] to view the images in single mode, or in 4 channel mode. Press [ESC] to stop recording and exit from the “RECORD” mode. You can access the image and audio of the Self-Guard, or copy off the Self-Guard’s data by the network from a remote computer.
You can check on the camera’s recording location, and the operating status of it with the Self-Guard’s LCD. When using multiple cameras, you can see up to 4 images simultaneously from the LCD. Every time you press [▽] in “2.CAMERA” mode, the image from each channel, which is turned on, appears in order. After the last channel shows up on the screen, it changes into 4 channel mode automatically, and displays four images from different cameras at once.
3. SEARCH Use [△] and [▽] to select “SEARCH”, and then press [ENT]. Then the next screen appears as below. This function lets you search the data saved by the motion detection of the image and by the sensor detection, or you can search the data saved by the sensor detection only. 1.MOTION/SENSOR- includes data saved by both motion and sensor detection 2.SENSOR- includes data saved only by sensor detection 3-1.MOTION/SENSOR Use [△] and [▽] to select “1.MOTION/SENSOR”, and then press [ENT].
All saved data are arranged according to the month and the year.
• Green Colored Date: There exists saved data. • Black Colored Date: There exists no saved data. • Pink Colored Date: Cursor position Use [◁] and [▷] to select the date you want, and then press [ENT]. Then the list of saved files appears on the screen as below. To move the cursor to the options at the bottom, use [▷] and [◁].
The name of the file is composed of hours, minutes, seconds and the camera’s channel numbers. For example, ‘15373501.sgv’ means that the file has started recording at 3: 37: 35 P.M. with camera 1. For 15224201.sgvx, ‘x’ means the file is locked to protect from deleting. To lock or unlock the file, select “LOCK” and press [ENT]. The locked files are not to be deleted before you unlock it. However, locked files can be deleted if you do the format (“4.OPTION” mode → “8.MEMORY SET” → “3.FORMAT”). ‘*.
||, ->, => : Stop, Play, High-Speed Play; If you press the [ENT], then the status bar changes to “-> (Play)” from the stopped status. If you press the [ENT], then the status bar changes to “=> (High-Speed Play)” from the Play status. If you press the [ENT], then the status bar changes to “-> (Play)” from the High-speed Play status. If you want to stop from Playing or High-Speed Playing, then press [ESC]. New files are created every hour on the hour.
The resolution of the current data appears on the lower left side of the magnified screen, and the magnification ratio appears on the lower right side of the LCD screen. In the magnification mode, you can move to the left, right, up, and down direction by using the direction buttons, and press [ENT] to change the magnification ratios, and the ratios repeat x 1 → x 4 →x 16 as you press [ENT] continuously.
4. OPTION Select “OPTION” using the direction buttons, and press [ENT]. Then the next screen appears in the LCD as below. Use [△] and [▽] to select an option and press [ENT]. Then the window displays with next options related to the previous option menu for you to change the values. To change the values, use [▷] and [◁]. 4-1.
Select “1.CAMERA SET” using the direction buttons, and press [ENT]. Then the next screen appears in the LCD as below. In order to return to the previous menu, press [ESC]. Self-Guard has one built-in camera in the front, and can add one more internal camera in the back of the unit. You can connect up to four more external cameras to your SelfGuard through the docking station. And you can connect a button-hole camera with microphone (SG-911) to your Self-Guard. You can turn on and off each camera.
Be sure to turn off the cameras that are not connected to the Self-Guard in the menu. Read below instructions for the “BUTTON CAM” function if you have purchased a SG911-“Button Camera with Microphone” 1. Insert the Button Camera into the Self-Guard’s connector which is located on bottom of the Self-Guard unit. 2. Turn on the “BUTTON CAM” function. 1. Turn off the “BUTTON CAM” function. 2.
camera from the unit, then the Self-Guard may go into the Record or Sleep mode. When this happens, press ESC button to go into main menu. If you turn off “BUTTON CAM” function, then it will turn off button camera and its microphone, and restore the settings before the use of “BUTTON CAM” function for camera(s) and built-in microphone. The types of external cameras can be set either in “NTSC” or “PAL”. Select “8.
saturation, and contrast, and then use [◁] and [▷] to change the value ranging from 1 to 20. 4-2. RECORD SET Select “2.RECORD SET” using the direction buttons, and press [ENT]. Then the next screen appears in the LCD as below. 4-2-1. VIDEO SET Select “1.VIDEO SET” using the direction buttons, and press [ENT]. Then the next screen appears in the LCD as below.
4-2-1-1. VIDEO This function turns on and off recording moving images. Set it to off to record audio only (SG-2000, SG-3000 only). 4-2-1-2. QUALITY (Image Quality) There are five image quality levels (LL, L, M, H, and HH). If you set this level to “HH”, then you get more clear images than in other levels, but a larger file size will result. On the other hand, if you set the level to “LL”, then it requires smaller file sizes, but you get less clear images compared to the images in “HH”.
those small motions recorded, and it will take much more time for you to search the data that you want. In addition, the available memory left for later decreases as the file size gets bigger, and the battery fades quickly. 4-2-1-4. FPS (Recording frames per second) Recording frames per second (FPS) depends on the different values for the Image Resolution.
At dawn, the light becomes bright from dark, generating a lot of noise when the SelfGuard is in such circumstance. And the Self-Guard may recognize those noises as a motion. In this case, you can set this level to “H” or “HH” to cut the noise. However, if you set the level to “H” or “HH”, then the motion detection algorithm of the Self-Guard may recognize the actual small motions as noise, and does not record those small motions. So, set the level to “M” except for the special cases. 4-2-1-7.
the Self-Guard to detect the motions. Accordingly, be sure to select at least one block in order for the Self-Guard to detect and record the images. 4-2-2. AUDIO SET (SG-2000, SG-3000 only) This function turns on and off audio recording function, and you can select either a built-in microphone or an external microphone. When you turn on “3.EXT MIC”, be sure that there is an external microphone connected to the external microphone input port to record audio. Set off “1.AUDIO” to record video only. 4-2-3.
the Self-Guard stops from recording video, and returns back to the initial menu mode, displaying “STOP! MEM FULL” on the LCD screen. Press any button to remove this message from the screen. If “1.AUTO OFF” (“4. OPTION” mode → “9.OTHERS” → “3.POWER SET”) is not set to “0 minute” but instead, set to “1-9 minutes”, then the Self-Guard automatically turns off its power after selected time gets elapsed.
preset time schedule, Self-Guard exits from the Sleep mode and starts to record. If you press [ESC] or [ENT] when the Self-Guard is in the sleep mode, then the LCD will display with a message, “CHECK SCHEDULE” for 5 seconds. During this message is displayed on the LCD, if you press [ESC], then Self-Guard exits from the sleep mode and goes into the menu mode. If you do not press [ESC] for that 5 seconds, then the Self-Guard keeps its sleep mode. 4-2-6-1.
4-2-6-3. 11-14 : OFF Recording time schedule number 2. 4-2-6-4. 14-17 : OFF Recording time schedule number 3. 4-2-6-5. 17-20 : OFF Recording time schedule number 4. 4-2-7. Timestamp Set 4-2-7-1. TIMESTAMP This function is to make the time and date information appear and overlap with the recorded image. 4-2-7-1. POSITION Use [◁] or [▷] button to change the position of Timestamp either to TOP or BOTTOM.
4-3. SEARCH SET Select “3.SEARCH SET” using the direction buttons, and press [ENT]. Then the next screen appears in the LCD as below. 4-3-1. REPEAT: OFF If you turn on “a. REPEAT”, then it keeps repeating playback the file. When it is turned off, then the file stops from playing after its first playback. 4-3-2. AUDIO: ON If you turn on “2. AUDIO”, then “3.BT AUDIO” automatically becomes “OFF”, and plays the audio recorded by the microphone (internal or external). If you turn off “2.
4-3-3. BT AUDIO: OFF (SG-3000 only) You can select one from the 8 options (OFF, BT1 – BT7). If you select OFF for “3. BT AUDIO“, then the Self-Guard does not play the audio recorded by the slave Self-Guard via Bluetooth. If you select one from BT1 to BT7, then “2.AUDIO” automatically becomes “OFF”, and the audio from a Bluetooth channel gets played. If “3.BT AUDIO” is OFF and “2.AUDIO” is ON, then the Self-Guard play the audio recorded by the microphone. If you turn off both for the “2.AUDIO” and “3.
If you turn off the Time Sync function, then it does not synchronize with the time even if you change the channels by pressing [▽], or press “-> (Play)” or “|> (Move forward by 1 frame)” after changing the channel. But, if you switch into 4-channel mode and press “-> (Play)” or “|> (Move forward by 1 frame)”, then the files are synchronized with the exact or closest time regardless of the Time Sync ON, OFF.
Using [◁] and [▷], you can move the cursor to the Date, Month, Year, and the Time, and use [△] and [▽] to change those variables. There are three ways to arrange these variables, and it varies in different localities. Move the cursor to “TYPE” using [◁] and [▷], and press [△] and [▽] to change among three different types. The types will be changed in regular sequence (DD/MM/YY → MM/DD/YY → YY/MM/DD). After setting all the variables, be sure to press [ENT] to save those new variables. 4-4-1.
4-5. REMOTE SET Select “5.REMOTE SET” using the direction buttons, and press [ENT]. Then the next screen appears in the LCD as below. To go to the previous menu, press [ESC]. 4-5-1.
4-5-1-1. LAN: OFF If “1.LAN” is set to on, then you can connect to the Self-Guard with your computer with the ID and the password by the network from a remote place. But, if “1.LAN” is set to off, then you cannot connect to the Self-Guard. When you are not using the LAN, turn it off to save the battery. 4-5-1-2. SET IP ADDR This function sets the address for IP, GATEWAY, and SUBNET MASK.
Self-Guard from a remote place. The Wireless-G Access Point is already set for immediate use once connected to the internet. Select 2.WLAN SET from 4.OPTION and then 5.REMOTE SET. Then the next screen appears in the LCD as below. 4-5-2-1. WLAN Before using WLAN function, turn on 1.USB (4.OPTION Æ 7.USB SET), and then turn on WLAN function to connect to the Self-Guard from a remote place.
Once the wireless LAN connection is accomplished, this function is to verify on the IP address that the Self-Guard is using, the GATEWAY address of the “Wireless-G Access Point”, the name of the “Wireless –G Access Point - SSID, and GLOBAL IP address of the of the “Wireless-G Access Point”. The GLOBAL IP address of the “Wireless-G Access Point” is used to connect to Self-Guard units from a remote place with the provided remote software.
Wireless LAN function of Self-Guard is encrypted with 128bit WEP Key of Hexadecimal Notation, 26 Characters-Roman alphabet. If you do not want to use WEP key, then turn off this function, however the Wireless LAN function will not be secured. When you turn off WEP KEY function, you need to change the WEB KEY of Wireless-G Access Point to “Disable”. Refer to the User’s Guide of Wireless-G Access Point to change the WEB KEY, and then input the new value using the direction buttons.
4-5-3. USER ID When connecting to the Self-Guard from a PC, you need the ID and the password for the remote access program. The initial default IDs are from “user00” to “user07”, and the passwords are “0000”. Move the cursor to the ID that you want to change for using the [△] and [▽], and press [ENT]. Then a new window appears to change the ID and the password as below.
4-6. SENSOR SET Select “6.SENSOR SET” using the direction buttons, and press [ENT]. Then the next screen appears in the LCD as below. This function sets several options regarding with the external sensors such as, the methods (Input/Output), and the kinds (NO/NC). You can turn on and off the sensors connected to the Self-Guard with this function. You can also link the sensors with the cameras to record the images of the camera when there is a change in the state of the sensors.
S: Number of each Sensor Port ( S1, S2, S3). On/Off: On(Sensor On), Off(Sensor Off). You must turn on the sensor port that is selected as the input, so that the Self-Guard can react to a change in the state of the sensor connected to the input port. When you set it to off, Self-Guard does not respond to any changes in the sate of the sensors. The sensor ports set as the output must be turned on to activate connected components (siren, warning lamp etc.).
“EDGE” mode, it starts to record audio and video for the time set in the “2.VIDEO TIME” and “3.AUDIO TIME” as soon as there is a change in the state of the sensors. In the “NORM” mode, it starts to record audio and video as soon as the sensor detects a change in its state until the sensor goes back to the original state, regardless of the “2.VIDEO TIME” and “3.AUDIO TIME”. In other words, if you set the “1.REC TYPE” to “NORM” then “2.VIDEO TIME” and “3.AUDIO TIME” are deactivated. 4-6-2.
Select “7.USB SET” using the direction buttons, and press [ENT]. Then the next screen appears in the LCD as below. To go to the previous menu, press [ESC]. This option turns on and off the USB function. When you are not using the USB memory device, turn it off to save the battery. Do not insert or remove USB memory devices from the USB port in the Self-Guard while recording or searching.
Cautions: Do not insert or remove USB memory devices from the USB port in the SelfGuard while recording or searching. When you remove the USB memory device from the Self-Guard, you must exit from “RECORD” or “SEARCH” mode, and select “REMOVE USB” from main menu and press [ENT] button. After “REMOVE USB NOW” message appears on the LCD, you can remove the USB memory device from the SelfGuard.
4-8-1. CAPACITY This information lists total capacity and used memory of each memory. 4-8-2. BUILT-IN Turn OFF this function when you want to store data to external memory devices only. When this function is OFF and there is no external memory device to record the data, Self-Guard records data onto the built-in memory. If external memory device gets available again, then Self-Guard closes the file being recorded to the built-in memory and starts to record the data onto the external memory device.
4-8-3. FORMAT “FORMAT” is to format the memories, and clear all the data saved in the memory. Note that this memory format function deletes the data even if they are locked from deleting in “SEARCH”. There are three types of memories you can format; “BUILT-IN”, “MICRO SD”, and “USB”. “BUILT-IN” is the built-in, internal memory of the Self-Guard. “MICRO SD” is the extensive memory device placed on the top of the Self-Guard, which can be inserted or removed by the user.
4-9. OTHERS Select “OTHERS” using the direction buttons, and press [ENT]. Then the next screen appears in the LCD as below.
4-9-1. PASSWORD SET You can prohibit people without authority from accessing the Self-Guard by setting up a password for each function (BOOTING, OPTION, SEARCH, and RECORD). You can turn on and off each function in “CHANGE PWD”. Functions BOOTING When each function is set with a password Put in the password for the Self-Guard to operate when you turn it on. OPTION Put in the password to change various settings or options. SEARCH Put in the password to search the data.
The password reads as “****” as you put in the password. Using [△] and [▽], choose a number for your password, then the number reads as ‘*’, and the cursor moves to the next position as you press [▷]. After you complete putting in all the numbers, press [ENT] and repeat the same process until you complete putting in all the numbers for the password. Once you put in the correct value that matches with the old password, you will be asked to put in the new password.
Self-Guard has the A/V (Audio/ Video) output ports, so that you can connect other components such as, an external monitor and a speaker like a TV. So, you can see the larger images, and hear the sounds in better-quality than you can in the LCD of the Self-Guard. If you press [△] while you playback the data with an external monitor, you can choose the menu (OSD) to appear on the screen or not. However, [△] is also used to magnify the image while you playback the data from the LCD. So, if “1.
rest of the modes besides “RECORD” and “TRANSMIT”, it turns off the power completely. Set the time to 0 to deactivate the “1. AUTO OFF” function. 4-9-3-2. SAVE AC: OFF This function is to save the power by using the low-powering technology. If there is no motion then the Self-Guard goes into the sleep-mode. After 2 seconds have elapsed, the Self-Guard wake up and check if there is a motion.
Self-Guard goes into sleep-mode again, but if there is a motion then the Self-Guard start to record. This low-powering technology is very important when you are using the battery as power source for the Self-Guard. In the case that you want to record objects passing once and quickly before the Self-Guard, then turn off this function. Caution: Set it to off when using the Remote Access (LAN) or the Bluetooth. 4-9-3-4.
“AUDIO DET” is set to on, then the Self-Guard starts to record audio when the SelfGuard detects sounds from the microphone regardless of the motions detected from the camera. Audio recording time set is the same as with the above “Video Recording Time Set”. Caution: If you set this time to 0, then the Self-Guard will not record the sound even if it detects sound. 4-9-3-7. AUDIO DET: OFF This is whether to turn on and off audio detection function.
as soon as it detects audio sound even when it is in the sleep mode. In this mode, SelfGuard is programmed to record with any audio detection, so you should be careful in turning this function to ON in a loud place to prevent from wasting the battery. When this function is set to CON: Self-Guard is programmed to record constantly regardless of audio or motion detection. In this mode, battery gets consumed very fast requiring your attention.
The black colored date/time (> 03/10 14:19:51) indicates you of the time that you turned on the Self-Guard. The blue colored date/time (< 04/11 11:56:31) indicates you of the time that you turned off the Self-Guard. 4-9-4. ALARM SET If you set the alarm volume too loud, then that sound may be louder than the audio detected by the Self-Guard’s internal microphone and the Self-Guard may not record the audio accordingly. Be cautious when you set the volume to high level. 4-9-4-1.
4-9-4-1-2. TIME: 0.2 When a motion is detected by the camera then the Self-Guard generates an alarm from the internal speaker. The duration of the alarm is from 0.2 to 9 seconds. 4-9-4-1-3. TYPE: 1 Set types for the alarm when a motion is detected by the camera. There are 5 different types for the alarm (1 - 5). 4-9-4-1-4. VOLUME: 5 Set the volume for the alarm when a motion is detected by the camera. There are 9 different levels for the volume (1 - 9). 4-9-4-2.
4-9-4-2-1. ON/OFF: OFF Set the alarm function when there is a change in the state of the sensor selected as the input. 4-9-4-2-2. TIME: 0.2 When there is a change in the state of the sensor selected as an input, the Self-Guard generates an alarm from the internal speaker. The duration of the alarm is from 0.2 to 9 seconds. 4-9-4-2-3. TYPE: 2 Set the type for the alarm when there is a change in the state of the sensor selected as an input. There are 5 different types for the alarm (1 - 5). 4-9-4-2-4.
4-9-4-3-1. CHANNEL SET Turns ON/OFF the alarm for each Bluetooth channel when there is a motion detected by the camera of the Self-Guards which are connected wirelessly via Bluetooth. 4-9-4-3-2. TIME: 0.2 When there is a motion detected by the camera of the Self-Guards which are connected wirelessly via Bluetooth, the Self-Guard generates an alarm from the internal speaker. The duration of the alarm is from 0.2 to 9 seconds. 4-9-4-3-3.
Set the volume for the alarm when there is a motion detected by the camera of the Self-Guards which are connected wirelessly via Bluetooth. There are 9 different levels for the volume (1 - 9). 4-9-5. SG-921 SET If you did not purchase the SG-921(Wireless Receiver), you don’t need to read this part. This function is to control the SG-921, which can receive the data transmitted from the “analog wireless transmission camera (2.4 GHz)”. You must turn it on to activate this function.
“Version” indicates of the Self-Guard’s version for its software and hardware. 4-9-7-1. SD DOWNLOAD This function can be used only with the MICRO SD memory card for the use of upgrades. You can make a MICRO SD memory card to be upgradeable by copying an upgrade file or a version file for each model to the MICRO SD card’s route directory. Insert that upgradeable MICRO SD memory card into the memory card slot on the unit, and select “1.
4-9-9. SG NAME This function is to put in the Self-Guard’s name, and used to back up the data of many Self-Guards to the MICRO SD or USB memory devices (USB Memory or USB Hard Disk). Self-Guard creates a directory name by the date, and the file name by the time.
The number which appears under the SG name is the product serial number. This serial number gets stored in a file together with the video and audio. When you are recording with several Self-Guard units, this serial number will be used to find out which Self-Guard is used for a certain file. When you playback a file with provided software, it will show with the product serial number so that you know which Self-Guard unit is used for that recorded file. Select either 1.MICRO SD or 2.
If you set the Self-Guard to the “TRANSMIT” mode, then you can access the image and voice of the Self-Guard currently being recorded using a computer by LAN in the remote places. Also, you can copy the data in the Self-Guard to your remote computer. Using the Bluetooth (SG-3000 only), you can wirelessly access or copy the image and voice of other Self-Guards with a Self-Guard from a remote place.
Select “BLUETOOTH” using the direction buttons, and press [ENT]. Then the next screen appears in the LCD as below. To go to the previous menu, press [ESC]. 6-1. CONNECT SET This function is to connect a master Self-Guard to seven (7) other slave Self-Guards wirelessly via Bluetooth, and “1.CONNECT SET” can only be activated when you select “2.M/S:MASTER” as MASTER. Move the cursor to “1.
Select a Bluetooth number that you want to connect to using [△] and [▽], and select “CONNECT” using [◁] and [▷] and then press [ENT] to start the connection. If you want to change a slave Self-Guard’s Bluetooth ID, camera channel number, and automatic connection ON/OFF information, use [△] and [▽] to select that Bluetooth number. Use [◁] and [▷] to select “EDIT” and press [ENT], then a new window appears as below. 6-1-1.
you get images from the camera channel number 2 transmitted to your master SelfGuard. If the camera channel number you have requested is not turned on, then the slave Self-Guard will send the images of the camera channel which is turned on and nearest to the requested channel number. 6-1-3. SLAVE PWD SET If “5.BLUETOOTH” in “1.PASSWORD SET” from “9.
This function is to find the Bluetooth ID for your Self-Guard. When you want to connect to the slave Self-Guards with your master Self-Guard, then you need to know the Bluetooth ID of the slave Self-Guard. You can confirm those Bluetooth IDs by checking from “3.MY ID” of the slave Self-Guards and then connect to the slave Self-Guards. 6-4. AUDIO: BT1 This function is to choose one Bluetooth channel to hear the audio from, once you are connected to several slave Self-Guards via Bluetooth (BT1-BT7). 6-5.
loading external antenna onto the Self-Guard you must set this type to “EXT”. 6-7. POWER: OFF This function turns ON or OFF the power for the Bluetooth. Turn it on to access the Bluetooth. Be sure to turn it off when you are not using the Bluetooth function to save the battery. II. Remote Access and Data Search/Playback Program After installing the Program to your computer in remote places from the Self-Guards, you can connect as many as 40 other Self-Guards to your computer simultaneously by LAN.
You can install the program to your computer with the provided CD. II-1. How to install Insert the CD into the CD-ROM, and check the files below.
To install the program, double-click SETUP icon. Then a new window appears as below, and starts installing the program.
. Type in the serial number and you can get this number from the back of your SelfGuard where the battery is placed in.
When the processes above are finished, then the program installment is completed. Now you will see an icon for the program on the ground screen.
Point the mouse to this icon, and double-click left side of the mouse, then a new window appears as below and starts the program. Of the many windows, move the mouse point to the window that you want to connect to, and click the right side of the mouse, and select one of the options from “Open Site/File”, “Change Remote Date/Time”, “Send Message”, “Pause”, “Play”, “Close Site/Data”, “Select Channel”, “Title on/off”, and “Audio”. Select “Open Site/File” to connect to the Self-Guard by LAN.
II-2 Network Setting 98
Make sure that TCP/IP Settings on your PC don’t match with that of Self-Guard’s in order to avoid mix-up. However, notice that IP Address in Connection Information of Data Search / Playback Program has to match with that of Self-Guard’s.
II-3. Remote Monitor and Save This function allows you to see and hear the image and audio being recorded in the Self-Guard, and save these data to your local computer. “Server Name”: Type in the name of the Self-Guard that you want to connect to. (It is the name for you to distinguish from several Self-Guards connected) “IP Address”: Type in the IP Address of the Self-Guard that you want to connect to. “User ID”: Type in the registered ID of the Self-Guard that you want to connect to.
II-4. Remote File Playback This function allows you to play the data stored in the Self-Guard with your computer by the date, time, and the camera channel. If you click the bar with a date, then you will see a calendar. Select the date you want and click “OK”, then you can playback the data saved in the selected date. If there is no data for the date which you selected, then you will see an error message.
II-5. Remote File Copy This function is to copy data stored in the Self-Guard to your local computer. Enter the Self-Guard’s IP Address, User ID, Password, and select the date and channel number, which you want it to be connected, then press “OK” button to get the list of files come under the date and camera channel number of that certain Self-Guard. Select a file, designate a folder for saving, and press “COPY” button, then a new folder for that date gets created under the designated folder.
II-6. File Search and Playback This function enables you to playback the data, which is stored in your computer. You can use the speed bar and the control buttons while you playback the data. Click “Browse” and select the folder and data that you want to playback, and then click “OK”. For example, select “C:\Sellf-Guard\20040701\03050701.sgv” and then click “OK”.
II-7. Other functions a. SETUP “Record”: You can choose to record or not to record the image and the audio which are being recorded in the Self-Guard connected to your local computer. “Sensor Alarm On/Off”: If the state of a sensor of the Self-Guard is changed, then you can choose to notify with an alarm to your local computer.
data) from “Browse”, and listen to the sound before you decide the alarm sound. You can set the duration of the alarm from 0 to 10 seconds. “Motion Alarm On/Off”: If Self-Guard detects a motion by the motion detection algorithm, then you can choose to notify with an alarm to your local computer. Select an alarm (wave data) from the “Browse” and listen to that sound before you decide according to your preference. You can set the alarm duration from 0 to 10 seconds.
c. Print , Save If you pause the video, then you can print or save an image in JPEG format. Also, you can print the data with the extension name of “snp”, or save it in the JPEG format. d. Position bar, Speed bar The position bar is one hour long, and indicates of the current position of the whole playback time. “Speed bar” is to control the speed of the playback. e.
Click on the “OPEN” button to select a file to be converted to AVI file format and click “CONVERT”. ※ If you use “Window Vista” in your PC, please make sure this program runs as an administrator in order to covert files into AVI files.
i. Minimize/Exit ”Minimize” is to minimize the window of the Data Search and Playback Program, and “Exit” is to exit from the Program.
III. OTHERS III-1. How to use Button Camera * How to connect Button Camera to the Self-Guard 1. Press ENT button for 2-3 seconds to turn on the unit. 2. Attach button camera directly to the “Connector to Docking” slot on the bottom of Self-Guard unit. 3. Turn ON the “OPTION” Æ “CAMERA SET” Æ “BUTTON CAM” function using the left or right direction buttons. 4. You are turning OFF all the internal camera and microphone when you turn ON “BUTTON CAM” function.
TROUBLESHOOTING GUIDE z Self-Guard shuts down its power for no reason. The Self-Guard automatically turns off the power or goes into the power-savings mode if you don’t press any button for a certain amount of time (1-9 minutes). This does not indicate malfunction of the system. In “RECORD” and “TRANSMIT” modes, Self-Guard turns off only the LCD, battery status LAMP, and recording status LAMP to save the battery.
before it turned off its power (“RECORD”, “TRANSMIT”, or to the initial mode). This function is very useful when you have installed the Self-Guard in the remote places far away from you. In the case that you have installed the Self-Guard in remote places, and there happens an electricity failure for some time and the electricity gets available to the Self-Guard again, then you have to go to where the Self-Guard is placed to turn it on, and to set it to the “RECORD” or “TRANSMIT” modes.
Warranty Guide This product has passed through quality control and testing. If this product shows any manufacturer’s defects during normal use, then there is a 12 months warranty service period from date of purchase. Check this warranty sheet first. Please contact the distributor or dealer after checking out any problems in the product. The standard for repairing, replacement or reimbursement follows Customer.
