Datasheet

ManualsBrandsSelectron ManualsMiscellaneousMounting for DIN rail

ESG

8.408.40

8.40

HRM PG 1 for HRM construction

HRT PG 1 for HRT construction

HRQ PG 1 for HRQ construction

A2- A1+

A1+ A2-

A2- A1+

Accessories

Profile casings PG for DIN-rail mounting

Casing for DIN-rails according to DIN 50 022

for solid-state relays of type HRM

• Input circuit protection

• Built-in indicator LED

Casing for DIN-rails according to DIN 50 022

for solid-state relays of type HRT

• Input circuit protection

• Built-in indicator LED

Casing for DIN-rails according to DIN 50 022

for solid-state relays of type HRQ

• Input circuit protection

• Built-in indicator LED

Dimensions (W x H x D)12 x 80 x 45 mm

Weight 20 g

Article number* 41920027

Dimensions (W x H x D)12 x 80 x 45 mm

Weight 20 g

Article number* 41920028

Dimensions (W x H x D)23 x 80 x 45 mm

Weight 28 g

Article number* 41920029

* Order data see chapter 1

Summary of content (8 pages)

PAGE 1
Accessories Profile casings PG for DIN-rail mounting Casing for DIN-rails according to DIN 50 022 for solid-state relays of type HRM • Input circuit protection • Built-in indicator LED A2- A1+ HRM PG 1 for HRM construction Dimensions (W x H x D)12 x 80 x 45 mm Weight 20 g Article number* 41920027 Casing for DIN-rails according to DIN 50 022 for solid-state relays of type HRT • Input circuit protection • Built-in indicator LED A1+ A2- HRT PG 1 for HRT construction Dimensions (W x H x D)12 x 80 x 45 mm
PAGE 2
Accessories Heat sink for 1- and 2-phases solid-state relays A C 62 48 30 60 10 134 124 35 14 120 72 B Depth 75 mm Depth 65 mm Depth 100 mm 10 Dimension A: Dimension B: Dimension C: 83 It is absolutely necessary to use heat conduction foil or heat conductive paste between solid-state relay and heat sink.
PAGE 3
Accessories Ventilator for 1- and 2-phases solid-state relays Ventilator kit for heat sink HRK 0,5C Type Operating voltage Power consumption Heat dissipation with HRK 0,5 Weight without heat sink Mounting-screws are contained in the kit Article number (Order data see chapter 1) 149 120 49 ESG 8.
PAGE 4
Accessories Heat sink for 3-phases solid-state relays B 67 6 10 A 105 Al constructions: Depht 75 mm 112 It is absolutely necessary to use heat conductive paste between solid-state relay and heat sink. Description Heat sink 0,8 °C/W Heat sink 5,0 °C/W (Order data see chapter 1) Type HRK 0,8 HRK 5,0 Dimension A B Weight 795 g 190 g Article number 41920019 41920020 ESG 8.
PAGE 5
Accessories Ventilator for 3-phases solid-state relays Ventilator kit for heat sink HRK 0,8 Type Operating voltage Power consumption Heat dissipation with HRK 0,8 Weight without heat sink Mounting-screws are contained in the kit Article number (Order data see chapter 1) 1 3 41920002 5 A1 B1 A2 B2 2 4 6 38 140 102 HRK 0,8LB 230 230 Vac 20 W 0,25 °C/W 730 g 120 ESG 8.
PAGE 6
Accessories Thermo switch for 3-phases solid-state relays Remark: The very small case of the thermo switch and the direct mounting on the heat sink guarantees a fast reaction on temperature changes. If the thermo switch is connected in series with the drive voltage of the SSR, it disconnects the drive as soon as the admissible operation temperature is exceeded. The drive will only be released, when the operation temperature reaches the correct value again.
PAGE 7
Accessories DIN-mounting, heath conduction foil and over-voltage protection DIN-mounting DB 2 for construction HRS (Order data see chapter 1) Weight 60 g Article no. 41920013 50 65 44 = = Heath conduction foil Type B: WLF 1PH Type C: WLF 3PH (Order data see chapter 1) Weight - Article no.
PAGE 8
Accessories Protection cover Description Protection cover for HRS (Order data see chapter 1) Type SA 2 Weight 11 g Article no. 41920012 27,5 44 66 12 Description Protection cover for HRV (Order data see chapter 1) Type SA 3 112 Weight 28 g Article no 41920026 29 73 16 ESG 8.