TM-U220 Technical Reference guide EPSON English Rev.
TM-U220 Technical Reference Guide CAUTIONS ❏ This document shall apply only to the product(s) identified herein. ❏ No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. ❏ The contents of this document are subject to change without notice. Please contact us for the latest information.
About This Manual Aim of the Manual This manual was created to provide information on the TM-U220 printer for anyone who is developing hardware, installations, or programs. Programmers will also want to consult other documents. Contents of the Manual ii Chapter 1, “General Information.” General description of features plus specifications. Chapter 2, “System Planning.” Contains introduction of control methods and each connection form. Chapter 3, “Setup.
TM-U220 Technical Reference Guide Related Software and Documents Related software and documents Software/document name Description TM-U220 User’s Manual/ This provides basic handling procedures for the end user of the printer TM-U220 Technical Reference Guide This Manual ESC/POS Application Programming Guide This provides descriptions in Acrobat format of the commands used by each TM printer, along with sample programs and other information about the printers EPSON OPOS ADK This is a OCX driver E
iv Rev.
TM-U220 Technical Reference Guide Safety Precautions EMC and Safety Standards Applied Product Name: TM-U220A / TM-U220B / TM-U220D Model Name: M188A / M188B/ M188D The following standards are applied only to the printers that are so labeled. (EMC is tested using the EPSON’s power supply.) Europe: CE marking Safety: TÜV (EN 60950) North America: EMI: FCC/ICES-003 Class A Safety: UL60950/CSA C22.2 No.
FCC Compliance Statement For American Users This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
TM-U220 Technical Reference Guide Safety Precautions This section presents important information to ensure safe and effective use of this product. Please read this section carefully and store it in an accessible location. WARNING: ❏ Shut down your equipment immediately if it produces smoke, a strange odor, or unusual noise. Continued use may lead to fire or electric shock. Immediately unplug the equipment and contact your dealer or a Seiko Epson service center for advice.
CAUTION: ❏ Do not connect cables other than as described in this manual. Different connections may cause equipment damage and burning. ❏ Be sure to set this equipment on a firm, stable, horizontal surface. Product may break or cause injury if it falls. ❏ Do not use in locations subject to high humidity or dust levels. Excessive humidity and dust may cause equipment damage, fire, or shock. ❏ Do not place heavy objects on top of this product. Never stand or lean on this product.
TM-U220 Technical Reference Guide Contents TM-U220 Technical Reference guide Chapter 1 General Information 1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.2 Printer handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.3 Printing . . . . . . . . . . . . .
2.3.3 Pass-through connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4 Parallel Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 USB connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6 Ethernet connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 2-8 2-8 2-9 Chapter 3 Setup 3.
TM-U220 Technical Reference Guide 4.3 Autocutter Jam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4 Printer Stops Printing / Printer Repeats Printing on a Line . . . . . . . . . . . . . 4.5 Printer prints “?“ or Incorrect Data With Serial Interface . . . . . . . . . . . . . . 4.6 Print Speed is Slow When Using Windows Printer Driver . . . . . . . . . . . . . . . 4.7 Printer doesn’t cut roll paper with the autocutter . . . . . . . . . . . . . . . . .
6.1.7 Use for Journal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 6.1.8 New functions added . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 6.1.8.1 Wall hanging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 6.1.8.2 NV bit-image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 6.1.8.3 User NV memory . . . . . . . . . . . . . . . . .
TM-U220 Technical Reference Guide C.4 Page 3 (PC860: Portuguese) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.5 Page 4 (PC863: Canadian-French) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.6 Page 5 (PC865: Nordic) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.7 Page 6 (Hiragana) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.
xiv Rev.
TM-U220 Technical Reference Guide Chapter 1 General Information 1.1 Features The TM-U220 is a POS printer that can print receipt paper (paper roll). The TM-U220 is designed to be compatible with existing systems built around a TM-U210. 1.1.1 General ❏ Compact and lightweight. ❏ 3 model types are provided. (See “Printer types” (page 1-2)) ❏ Excellent reliability and long life due to adoption of a stepping motor both for moving the carriage and for paper feeding.
1.2 Product Structure 1.2.1 Printer types TM-U220 has 3 model types: A, B, D. The features are as following. Type A Type B Type D Two color printing Yes Yes Yes Autocutter Yes Yes No Take up device Yes No No paper width (mm) 76 76/ 69.5/ 57.5 76/ 69.5/ 57.
TM-U220 Technical Reference Guide 1.2.3 Related materials for TM-U220 TM-U220 has the related materials listed in the following table. Category Name Description Options WH-10 This is an optional unit for installing the printer on a wall. DF-10 Affixing Velcro tape DC-21 This is optional power supply cable to gain power from user’s power supply.
1.3 Consumables 1.3.1 Ribbons This printer needs a ribbon cassette to print receipts. We provide 3 ribbon cassettes: ❏ EPSON ribbon cassette, ERC-38 (B) (Life: 3,000,000 characters / Color: Black) ❏ EPSON ribbon cassette, ERC-38 (P) (Life: 4,000,000 characters / Color: Purple) ❏ EPSON ribbon cassette, ERC-38 (B/R) (Life: 1,500,000 characters / Color: Black) (Life: 750,000 characters / Color: Red) Note: These ribbon cassette life numbers are under the EPSON test conditions. 1.3.
TM-U220 Technical Reference Guide 1.4 Product Specifications Overview Print method serial impact dot matrix Paper width 76 mm / 69.5 mm / 57.5 mm {3.00"/2.74"/2.26"} Cut type There are 2 types. The type can be changed. Partial cut (cutting with one point on left edge left uncut) (default) or Full cut Character sets 95 alphanumeric, 48 international characters, Extended graphics: 128 × 12 pages.
1.5 Printing and paper Specifications Printing method: Serial impact dot matrix Head wire configuration: 9-pin serial configuration Printing direction: Bidirectional printing (logic seeking) Print speed: *1 Approximately 4.7 lps (printing 40 columns per line at 16 cpi) Approximately 6.0 lps (printing 30 columns per line at 16 cpi, with 1/8" line spacing) (except data transmission and processing time) Paper width: 76 mm / 69.5 mm / 57.5 mm {3.00"/2.74"/2.26"} Printing width: 63.4 mm / 57 mm / 47.
TM-U220 Technical Reference Guide The dot width of the printable area depends on DIP switch setting and paper width as shown in the following table. Dot width of Printable area Paper width DIP SW2-1 setting ON OFF 76 mm 385 half dots 400 half dots 69.5 mm 360 half dots 360 half dots 57.5 mm 297 half dots 300 half dots Character Dimensions, Characters Per Inch, Characters Per line Character dimensions Dot spacing between characters Character configuration Horiz. x Vert.
1.5.1 Autocutter (for Type A / B) Cutting method: By separated-blade scissors Cutting type: ❏ Partial cut (one point left uncut) (default) ❏ Full cut (completely cut off) See “Select Autocutter action” (page 3-28) for changing cut type. Note: It is recommended to feed approximately 2.116 mm or more in advance before printing to prevent dot displacement after cutting. Changing between partial cut and full cut is not controlled by a software command.
TM-U220 Technical Reference Guide 1.5.2 Paper Roll Supply Supply method: Drop-in method Paper roll end detection: Detection method: Mechanical microswitch Detection position: Positioned within the paper path for the roll paper; detects the end of the roll paper Near-end detector: Detection method: Mechanical microswitch Inner diameter of the roll paper core: 10.5 to 12.
1.5.2.1 Paper Specifications Paper feeding method: Friction feed Paper feed interval: Initial setting: Approximately 4.23mm {1/6"} Can be set in units of approximately 0.18mm {1/144"} by ESC/POS command Paper feed speed: 30 lps (approximately 4.99" /s) (during continuous feeding) [lps: lines per second] Roll paper width: 76 ± 0.5 mm (3" ± 0.02") / 69.5 ± 0.5 mm (2.74" ± 0.02") / 57.5 ± 0.5 mm (2.26" ± 0.02") Maximum diameter: 83 mm (3.
TM-U220 Technical Reference Guide 1.5.2.2 Printable Area Cutting position (manual cutter) (Type A, B) Cutting position (autocutter) (Type A, B) Cutting position (manual cutter) (Type D) 34.9 27 22.1 (6.8) 63.4 (5.8) Maximum 200dots, 400 positions [Units: mm] 76 Printable area for 76mm width paper Rev.
Cutting position (manual cutter) (Type B) Cutting position (autocutter) (Type B) Cutting position (manual cutter) (Type D) 34.9 27 22.1 (6.7) 57 (5.8) Maximum 180 dots, 360 positions [Units: mm] 69.5 Printable area for 69.5mm width paper 1-12 General Information Rev.
TM-U220 Technical Reference Guide Cutting position (manual cutter) (Type B) Cutting position (autocutter) (Type B) Cutting position (manual cutter) (Type D) 34.9 27 22.1 (4.2) (5.8) 47.5 Maximum 150 dots, 300 positions [Units: mm] 57.5 Printable area for 57.5mm width paper 1.6 Other Specifications 1.6.1 EMI and Safety Standards Applied 1.6.1.1 Printer (TM-U220) EMC is Tested Using the EPSON’s AC adapter. Europe: North America: Japan: Oceania: Rev.
1.6.1.2 AC Adapter C (packaged in ANK model) Europe: CE Marking Directive 89/336/EEC EN55022 Class B EN55024 IEC 61000-4-2 IEC 61000-4-3 IEC 61000-4-4 IEC 61000-4-5 IEC 61000-4-6 IEC 61000-4-11 EN61000-3-2 EN61000-3-3 Safety: EN 60950 North America: Safety: UL1950/CSA C22.2 No. 950 Japan: Electrical Appliance and Material Control Law Oceania: Safety: AS3260 1.6.1.
TM-U220 Technical Reference Guide 1.6.2 Reliability Life: Mechanism: 7,500,000 lines MTBF: 180,000 hours Failure is defined as a Random Failure occurring at the time of the Random Failure Period. MCBF: 18,000,000 lines This is an average failure interval based on failures relating to Wearout and Random Failures up to the life of 7.5 million lines. Print head life: 150 million characters (using an average of 2 dots/wire per character). (The printing pattern is EPSON test pattern).
Vibration resistance: When packed: Frequency: 5 to 55 Hz Acceleration: 19.6m/s2 {2 G} Sweep: 10 minutes (half cycle) Duration: 1 hour Directions: x, y, and z No external or internal damage should be found after the vibration test, and the unit should operate normally. Impact resistance: When packed: Package: EPSON standard package Height: 60 cm (2 feet) Directions: 1 corner, 3 edges, and 6 surfaces No external or internal damage should be found after the drop test, and the unit should operate normally.
TM-U220 Technical Reference Guide 1.7 External Dimensions and Mass 1.7.1 External Dimensions and Mass Model type External Dimensions Mass Width Height Depth Type A 160 mm {Approximately 6.3"} 157.5 mm {Approximately 6.2"} 286 mm {Approximately 11.3"} Approximately 2.7 kg {5.9 lb} Type B 160 mm {Approximately 6.3"} 138.5 mm {Approximately 5.5"} 248 mm {Approximately 9.8"} Approximately 2.5 kg {5.5 lb} Type D 160 mm {Approximately 6.3"} 138.5 mm {Approximately 5.
1.7.1.2 Overview (Type B) 1-18 General Information Rev.
TM-U220 Technical Reference Guide 1.7.1.3 Overview (Type D) Rev.
1-20 General Information Rev.
TM-U220 Technical Reference Guide Chapter 2 System Planning This section provides you information for system planning. 2.1 Control Method A TM printer can print and be controlled using any of the following three methods: 1. Windows printer driver (EPSON Advanced Printer Driver) 2. EPSON OPOS ADK 3.
2.1.1.2 EPSON Advanced Printer Driver Components Installer recognizes PC environment in which the installation will be done and installs DLL files and software components necessary for operating automatically. Driver, sample program, or manual can be selected to be installed. ❏ Driver You can select a driver depending on the purpose of usage (installation can be done at the same time). Each has functions such as two-color printing, smoothing, continuous printing, and option selection for cutting method.
TM-U220 Technical Reference Guide ❏ Supported devices (For detailed information on which devices can be used, see the release note for the driver.) • EPSON receipt printer • EPSON customer display • EPSON cash drawer Note: The USB specification printer needs the USB driver and the Ethernet specification printer needs the IP setting utility in addition. For detailed information, please contact your dealer or EPSON. 2.1.
❏ Power on notice function (recovering automatically to the status before the power is turned off when turning on the power again) ❏ Offline buffer clear processing (deleting contents in print buffer at offline) ❏ Debugging function (trace function) • Logs between an application and CO (for used API and its return value) • Logs for device status (acquires causes for offline and errors in devices) 2.1.2.2 EPSON OPOS ADK Contents Any installer later than EPSON OPOS ADK Ver2.
TM-U220 Technical Reference Guide 2.1.2.3 EPSON OPOS ADK Supported Environment ❏ Supported interfaces • Serial, Parallel, USB, Ethernet ❏ Supported Operating Systems: Epson has confirmed performance with the following: • Windows 95 English Version Standard OSR2.5 • Windows 98 English Version Second Edition • Windows NT Ver 4.0 English Version SP5, SP6 • Windows 2000 English Version • Windows XP English Version ❏ Supported Development Languages • Visual Basic • VisualC++ 2.1.
2.2 Connection Form and Cables 2.3 Serial Connection When the TM printer is connected to the host PC with a serial interface, the following connection forms are possible: • Stand alone • Y-connection • Pass-through connection Connections for usable serial cross cables are as follows: The type of cable that should be used depends on the operation and the handshake method for the TM printer. You can operate the TM printer by Windows driver, OPOS, or ESC/POS commands.
TM-U220 Technical Reference Guide 2.3.1 Stand alone Both TM printer and customer display (DM-D) are connected to the host PC via serial port. 2 1 Application XON/XOFF TM side control control setting (except OPOS) DTR/DSR (DOS, OPOS, Visual C) RTS/CTS (DOS, Windows driver, Visual C, Visual Basic, MSComm) XON/XOFF 1 Type A or B — — 2 DM-D500: A,B Other DM-D: not available — — 1 — Type A or B Type B 2 — Type A or B Type B DTR/DSR 2.3.
2.3.3 Pass-through connections The TM printer is connected to the customer display (DM-D) via a serial port, and the DM-D is connected to the host PC via a serial port. Note: On the DM-D (DM-D500 etc...) which has a DIP switch to select Y-type connection, confirm that the DIP switch has been set to “Y-type connection: Disable.
TM-U220 Technical Reference Guide Modular (with UB-U02II) (with UB-U01II) Self-powered USB HUB (with UB-U01II) Note: UB-U01II has bus-powered USB HUB. Therefore This USB model printer can’t be connected directly to other bus powered HUB (including other UB-U01II equipped TM printer) and bus-powered function whose current consumption is over 100mA. If you would like to connect other USB model TM printer with UB-U01II, use a self powered USB HUB as shown in the above figure.
TM printers are connected to a network via a hub using an Ethernet cable. Note: If the TM printer is connected to the host PC via an Ethernet interface, a DM-D cannot be connected to the TM printer. We provide the IP address setup utility“EPSON TMNet WinConfig,” for setting the IP address of the Ethernet model TM printer on the host PC. Please contact EPSON or your dealer about “EPSON TMNet WinConfig” and the procedure for installing. 2-10 System Planning Rev.
TM-U220 Technical Reference Guide Chapter 3 Setup 3.1 Part Name and Basic Operation 3.1.1 Part name unit (Type A only) roll paper cover ribbon casette cover manual cutter power switch control panel This figure is Type A. 3.1.1.1 Connectors WARNING: Do not connect a telephone line to the drawer kick-out connector or the display module connector; otherwise the printer and the telephone line may be damaged. Rev.
You can connect up to four cables to the printer. They all connect to the connector panel (on the bottom rear of the printer), which is shown below. FG FG interface connector drawer kick-out connector DK DC24V power supply connector Note: This illustration shows the serial interface model. The other interface connector looks slightly different. 3.1.2 The Control Panel The control panel is shown below. ❏ POWER LED ❏ ERROR LED ❏ PAPER OUT LED ❏ FEED button 3.1.2.
TM-U220 Technical Reference Guide PAPER OUT On: The roll paper near end (*1) or real end is detected. Off: Paper is loaded (normal condition). Flashing: Self-test waiting state for test print. Note: The roll paper near-end sensor is available as an factory option. If the printer is not equipped with the roll paper near-end sensor, the roll paper near-end is always detected as paper present. See “Adjusting Position of Roll Paper Near End Detector” (page 3-27) for information on adjusting the detector.
3.2 Setup Flow You have to set up your printer to use it. And you can adjust some features by customizing them. This section describes the setup. The set up flow of preparing to use printer is below. 1. Printer set up ❏ Install Ribbon Cassette ❏ Install Paper Roll ❏ Connect the Printer to the Power Supply (See “Printer setup,” page 3-6) 2.
TM-U220 Technical Reference Guide Note: When you use OPOS (OCX driver from EPSON) or the Advanced Printer Driver, you need to install the driver. When you use ESC/POS commands, you don’t have to install drivers. For information on these drivers, see “Control Method” on page 2-1 and “Install a Printer Driver in the Host PC / POS Terminal” (page 3-34). This printer can be installed on a wall. See “How to Install the Printer on a Wall with the WH-10” in Appendix B for details.
3.3 Printer setup 3.3.1 Installing or Replacing the Ribbon Cassette EPSON recommends the use of genuine EPSON ribbon cassettes. Ribbon cassettes not manufactured by EPSON may cause damage to your printer that is not covered by EPSON’s warranties. To install the ribbon cassette for the first time or to replace a used ribbon, follow the steps below: 1. Unpack the ribbon cassette and turn the knob in the direction shown to take up any slack. Knob 2.
TM-U220 Technical Reference Guide 3.3.2 Installing the Roll Paper The installing procedure is little different between Type A and Type B, D. CAUTION: Be sure to use roll paper that meets the specifications. Be sure not to touch the manual cutter. Otherwise your fingers might be injured. Rev.
3.3.2.1 Installing rhe Roll Paper for Type B, D 1. Using scissors, cut the leading edge of the roll paper, as shown in the left figure. 2. Turn on the printer and open the roll paper cover by using the tab, as shown in the left. Tab 3. Insert the roll paper, as shown on the left. Note: Note the direction the paper comes off the roll, as shown below. When using 2-ply roll paper, be sure that the top and bottom sheets are aligned at the paper exit. See the below illustration. 4.
TM-U220 Technical Reference Guide 3.3.2.2 Installing the Roll Paper for Type A 1. Using scissors, cut the leading edge of the roll paper, as shown in the left figure. Tab 2. Turn on the printer and open the roll paper cover by using the tab, as shown in the left. Note: The printer feeds for 30 mm automatically if the roll paper cover is open. This is a normal operation to prevent the printer from damaging the paper when the roll paper cover is opened or closed.
4. Insert the roll paper, as shown in the left. Note: Note the direction the paper comes off the roll, as shown in following When using 2-ply roll paper, be sure that the top and bottom sheets are aligned at the paper exit. See below illustration. 5. Close the roll paper cover. 6. If you are not using a take-up spool, pull out a small amount of roll paper and close the roll paper cover; then tear off the paper with the manual cutter. You can skip steps 6 through 11. 7.
TM-U220 Technical Reference Guide 8. Close the unit, as shown in the left illustration. 9. Insert the end of the bottom paper (journal paper) into the paper take-up spool, as shown in following. 10. Insert the paper take-up spool in the printer. Be sure that the paper is aligned with the spool's flange, as shown. 11. Feed the paper with the FEED button so that the paper is taken up by the spool. 12. Close the roll paper cover and tear off the roll paper with the manual cutter, as shown. Rev.
Note: Since the printer does not feed even if the roll paper cover is open when the printer is turned off, make sure not to pinch the paper when the cover is closed. Do not open the roll paper cover during printing or paper feeding. When using the printer, be sure to cut the roll paper with the manual cutter after paper feeding is complete. 3.3.2.3 Replacing the Roll Paper 1. Turn on the printer and open the roll paper cover by using the tab, as shown. Tab 2.
TM-U220 Technical Reference Guide 3.3.3 Connecting the Power Supply Unit Use the power supply or equivalent for your printer as listed below. TM-U220 Alphanumeric model (Type A,B, D) TM-U220 Multilingual model (Type A,B, D) AC Adapter C (which is packed with ANK model) or PS-180 (Which is provided as option) PS-180 (which is packed with Multilingual model) Note: The AC Adapter packed in the carton box of ANK model cannot be used for the Multilingual model.
3. Plug the power supply cord into the connector shown below. FG FG DK DC24V Power supply connector Note: To remove the DC cable connector, make sure the power supply’s power cord is unplugged; then grasp the connector and pull it straight out. When you connect the power supply unit to the printer, we recommend to do a self test to confirm the operation. See “Self Test” (page 3-40) for details. 3.
TM-U220 Technical Reference Guide 3.4.2 Adjusting the DIP Switches The printer has two sets of DIP switches. The function of the DIP switches is different for each interface model. If you need to change settings, follow the steps below to make your changes: CAUTION: Turn off the power while removing the DIP switch cover to prevent an electric short, which can damage the printer. Use a crosshead screwdriver to remove the screw holding the DIP switch cover.
Parallel / USB / Ethernet model (Except serial) (DIP Switch 1) (DIP Switch 2) SW Function On Off SW Function On Off 1 Auto line feed Enabled Disabled 1 Print column selection 42/35 40/33 2 Receive buffer capacity 40 bytes 4 KB 2 Reserved (Auto cutter enable/ disable) Type A, B Fixed to On Type D Fixed to Off 3~7 Reserved - Fixed to Off 3~7 Reserved - Fixed to Off 8 BUSY condition Receive buffer full Receive buffer full or Offline 8 Used Not used Pin 31 reset signal No
TM-U220 Technical Reference Guide 3.4.2.
Note: See the previous page for “When the letters are STD.” See “Notes for DIP switch 2-1” (page 3-19) about the DIP SW 2-1 setting. When you use serial interface model with 1200bps, 2400bps, or 19200bps, you have to adjust DIP switch “Serial interface selection“ function and Memory switch “Serial communication condition“. Usually DIP switch 1-1 should be turned off. The right side up printing mode is a mode used for a printer that is hanging on a wall.
TM-U220 Technical Reference Guide 3.4.2.3 Notes for DIP switch 2-1 The DIP switch 2-1 defines the print columns as listed in the following table. DIP switch 2-1 status Paper width Character font ON OFF 76 mm Font A (9 x 9) 35 33 Font B (7 x 9) 42 40 Font A (9 x 9) 32 30 Font B (7 x 9) 40 36 Font A (9 x 9) 27 25 Font B (7 x 9) 33 30 69.5 mm 57.5 mm Unit: cpl (Character per line) Note: The cpl of a Kanji character font is available to be changed by an ESC/POS command.
Memory Switch 2 SW Function On Off 1 Reserved - Fixed to Off 2 Reserved - Fixed to Off 3 Selection of the character code system of GB2312 the Simplified Chinese 4 ~ 8 Reserved - GB18030 Fixed to Off Note: Msw 2-3: The memory switch Msw 2-3 affects the Simplified Chinese model only.
TM-U220 Technical Reference Guide Note: These setting can be set by “Memory switch setup mode.“ See “Memory Switch Setup Mode” on page 321. See “Adjusting Roll paper width” (page 3-26) also to adjust roll paper width.
3.4.4.1 Starting the memory switch setup mode Use the following procedure to start the memory switch setup mode. 1. Open the roll paper cover. 2. Turn the power on while pressing the paper FEED button. 3. Press the FEED button twice while POWER, ERROR, and PAPER OUT LEDs are lit. 4. Close the cover. The printer prints the enabled settings of the memory switches and instructions. 5. Follow the instructions to process the switch setup. Note: In the memory switch setup, the paper out LED may be flashing.
TM-U220 Technical Reference Guide 3.4.4.3 Operating procedure The procedures used for this process are described below. Entering Memory Switch Setting Mode 1. Open the paper roll cover and turn the power on while pressing the paper FEED button. 2. Press the paper FEED button twice while POWER, ERROR, and PAPER OUT LED are lighting. 3. Close the cover. The printer prints the current settings and setting instructions. Selecting Items to Set Open the paper roll cover.
Selecting individual settings ❏ Basic serial interface setting To select transmission conditions, first choose “Serial interface settings”; then select “Data length, handshake, or parity.” Press the FEED button the number of times required to select the desired “Serial interface settings” used for transmission conditions.
TM-U220 Technical Reference Guide ❏ Receive buffer full release condition Press the FEED button the number of times required to select the desired receive buffer full release condition setting.
3.4.5 Adjusting Roll paper width The TM-U220 accommodates 76 mm {3"},69.5 mm {2.74"}, 57.5 mm {2.26"} wide paper rolls. Note: When you use a near-end detector equipped model, be sure not to pinch the lead wires of the near-end detector between the roll paper guide and the roll paper holder, and to push the lead wires inside so that the lead wire of the paper-end detector does not contact the motor gear.
TM-U220 Technical Reference Guide 5. Tighten the spacer with two screws included with the guide. (See figure above.) 6. Set the memory switch (customize value) for the paper width. (See “Memory Switches” (page 3-19)) 3.4.6 Adjusting Position of Roll Paper Near End Detector Below are two reasons for the roll paper to require an NE detector adjustment. ❏ To adjust the location of detection for the diameter of the roll paper core. ❏ To adjust the amount of remaining paper. The procedure is as following. 1.
3.4.7 Select Autocutter action The autocutter action on the TM-U220 can be either “partial cut“ or “full cut.“ The procedure to change from one to the other is described below. Note: It is recommended to feed approximately 2.116 mm or more in advance of printing to prevent dot displacement after cutting. The cutting type (partial cut or full cut) must be selected before the printer is first used.
TM-U220 Technical Reference Guide 4. Loosen the screw as indicated in following figure. Remove the screw Loosen the screw Emergency cutter 5. Lift the top of the cutter unit upward towards you and remove from the dowel. dowel Cutter unit Rev.
6. When you select partial cut (default), you have to adjust the dowel to the right, as shown. When you select full cut, you have to adjust the dowel to left as shown. Partial cut Full cut 7. Tighten the two screws. 8. Set again the roll paper cover, and set the shaft which is taken out in step 3. 9. Install roll paper 10. Execute the self test to confirm the cutter action. (See “Self Test Procedure” (page 3-40)) 3.4.
TM-U220 Technical Reference Guide 3.4.8.1 Serial Interface model Before connecting any of the cables, make sure that both the printer and the host PC are turned off. 1. Plug the cable connector securely into the printer’s interface connector. 2. If the cable connector has screws on it, tighten the screws on both sides of the connector. 3. If your interface connector has a grounding wire, attach it to the printer using the screw labeled FG, which is next to the interface connector. 4.
Note: Hooking the USB cable through the locking wire saddle, as shown in the figure below, will prevent the cable from coming unplugged. USB upstream connector UB-BOARD Locking wire saddle USB cable USB downstream connector (Only for the USB HUB: UB-U01) DM connector Attaching locking wire saddle 3. Connect the USB cable from the host computer to the USB upstream connector. 4. For models that have the UB-U01II installed, a maximum of two USB devices can be connected to the USB downstream connector.
TM-U220 Technical Reference Guide 3.4.8.4 Ethernet interface The following view shows the part names of the UB-E01. 10BASE-T Ethernet interface connector LED (green) LED (red) Switch Be sure not to push the LEDs by accident If you press and hold this switch when the printer is on, the interface will be reset to the factory settings Before connecting any of the cables, make sure that both the printer and the host computer are turned off. 1.
3.4.8.5 Connecting a Drawer CAUTION: Be sure to connect a drawer that meets printer specifications. Connecting a drawer of the wrong specifications may result in damage to both the drawer and the printer. Never connect the telephone line to the drawer kick out connector (labeled “DK”). Doing so may result in damage to both the telephone line and the printer. Never connect the drawer cable to the customer display connector (labeled “DM-D”).
TM-U220 Technical Reference Guide Outline of install and Setup procedure is as follows. START 1. Installation OPOS ADK (Execute the Setup.exe in DISK1, and continue to installation by wizard) Is installation completed? ERROR Completed 2. Setup the OPOS & device setting by using SetupPOS utility For detail refer to [ User Manual] You can setup the OPOS and device setting by the SetupPOS utility. 2.1 Setup the OPOS & device setting ❏ Select the device and I/F setting ❏ Device specified setting Rev.
2.2. Device communication test by executing the CheckHealth ResultCode ERROR SUCCESS The OPOS and device settings are right. & The Install and Setup are completed. Confirm the error condition by referring to the [User's manual] (3. Confirmation by sample program) 4. Make a OPOS compliant program END 1. Installation. Execute the Setup.exe in DISK1. and continue to installation by wizard. 3-36 Setup Rev.
TM-U220 Technical Reference Guide 2. Set up the device and environment. 1. Set the device setting by using SetupPOS utility. • • Select the device and I/F setting. Device specified setting. (set the specified setting of the device) 2. Execute the CheckHealth Device communication test. • • If you get "SUCCESS", the setting of the device is right. If you get ResultCode (error), please re-check the device connection setting by following the User's Manual.
3.5.2 Advanced Printer Driver (APD) 3.5.2.1 Installing and Setting Up When you install and set up the APD, please refer to the “EPSON Advanced Printer Driver Install Manual.“ The Manual is a PDF file, which is provided with other manuals for the APD. Outline of installation and setup procedure is as follows. 1.
TM-U220 Technical Reference Guide 1. Install EPSON Advanced Printer Driver Execute the installer “ADT###e.exe,“ and select modules which you need. The recommended modules are shown below. Refer to the installation manual for details. EPSON TM-U220 Receipt (76mm): This module (printer driver) is required for printing on 76mm width receipt. EPSON TM-U220 Receipt (69.5mm): This module (printer driver) is required for printing on 69.5mm width receipt. EPSON TM-U220 Receipt: (57.
Note: You can use the printer with sample program (written in Microsoft Visual Basic, Visual C++). The sample program is provided separately. 3.6 Self Test The self test lets you know if your printer is operating properly. It checks the control circuits, printer mechanisms, print quality, control software version, and DIP switch settings. This test is independent of any other equipment or software, so it is a good idea to run it when you first set up the printer and if you have any trouble.
TM-U220 Technical Reference Guide Chapter 4 Troubleshooting This section describes general troubleshooting. 4.1 LED Blinking Pattern 4.1.1 Error Types The printer stops all printer operations for the selected paper section, goes offline, and the ERROR LED blinks when an error is detected. 4.1.1.
4.1.1.2 Recoverable Errors When a recoverable error occurs, after the cause of the error is removed, the printer can recover from the error by receiving an error recovery command without turning off the power: ERROR LED Blinking Pattern 160 ms ERROR Description Recovery Paper roll cover open error (*1) The roll paper cover is opend when printing.
TM-U220 Technical Reference Guide 4.2 Removing a Paper Jam CAUTION: Be sure not to touch the manual cutter. Otherwise your finger might be injured. 1. Turn the power off. 2. Open the roll paper cover by using the tab, as shown in the below illustration. 3. If you have a Type A printer, remove the take-up spool and open the unit by using the unit open lever, as shown in the illustration. Roll paper cover Tab lever 1. open the roll paper cover 2. (only type A) open the unit 4. Remove the jammed paper.
2. Turn off the printer, and close the roll paper cover, and turn it back on. Then the cutter blade returns to the normal position. If you would like not to turn off the printer, send an error recovery command and initialize printer command instead. 3. If the cutter blade doesn’t return to the normal position, return the cutter blade to the normal position by rotating the autocutter knob in the direction of the arrow.
TM-U220 Technical Reference Guide Note: *Multilingual means the printer model that can print any one of the following: Japanese Kanji, Simplified Chinese, Traditional Chinese, Thai characters, or Korean characters. Use the self test to confirm what model of printer you have, and then use the correct power supply. (See “Self Test Procedure” (page 3-40) for how to run the self test.) Rev.
Alphanumeric model ... SELF-TEST Resident Character Alphanumeric The following models are called Multilingual SELF-TEST ... ... SELF-TEST Resident Character Alphanumeric Traditional Chinese Resident Character Alphanumeric Chinese GB18030 Simplified Chinese model Traditional Chinese model SELF-TEST ... ... SELF-TEST Resident Character Alphanumeric Thai 3 pass Resident Character Alphanumeric Korean Thai model Korean model ...
TM-U220 Technical Reference Guide 4.5 Printer prints “?“ or Incorrect Data With Serial Interface If one of the following errors occurs during serial interface communication, the printer prints “?” or ignores the data, depending on the setting of DIP switch 1-1. ❏ Parity error ❏ Framing error ❏ Overrun error Note: For other errors, we recommend confirming the transmission setting of DIP switch 1-3: Handshaking. 4.
4. Run any software program that sends data to the printer. The printer prints “Hexadecimal Dump” and then all the codes it receives in a two-column format. The first column contains the hexadecimal codes and the second column gives the ASCII characters that correspond to the codes. Part of a hexadecimal dump is shown below: Hexadecimal Dump To terminate hexadecimal dump, press FEED button three times. 1B 21 00 1B 26 02 40 40 . ! . . & . @ @ 1B 25 01 1B 63 34 00 1B . % . . c 4 . .
TM-U220 Technical Reference Guide Chapter 5 Application Development Information This section contains usable information to develop POS systems that use this printer. 5.1 Various Status Categories This printer is able to send various status reports to the host PC. This section describes about the kind of statuses and handling. Status Categories Description Drawer kick connector pin status Cash drawer is open or closed.
5.1.2 OPOS Note This section describes the summary of status handling. Refer to “OPOS ADK Application Development Guide General Functions” for details. 5.1.2.1 Checking the printer state The state of the printer can be checked through properties supported by the printer. For example, if the user wants to check if the printer cover is open, the CoverOpen property can be used. If OPOSPOSPrinter1.
TM-U220 Technical Reference Guide method, change the FlagWhenIdle property to TRUE. When all data has finished printing, the printer becomes idle and a StatusUpdateEvent is fired to the application with the value of PTR_SUE_IDLE. 5.1.2.2 Printer Errors and Status A change in printer status when asynchronous data is being sent is made available to the program by the firing of an ErrorEvent and StatusUpdateEvent.
5.2 Cash Drawer Control 5.2.1 Advanced Printer Driver 5.2.1.1 Drawer Open When you control a drawer which is connected to this printer using APD, you have 2 methods to open the drawer. The first method is using “Control font,” second is using “Status API.“ Below is as example of a program (Visual Basic) to open a cash drawer using Control font. 'Execute open cash drawer1. Printer.Font.Name = "control" Printer.Print "A" íThisîAî means ìopen the drawer1 with 50msec pulse.
TM-U220 Technical Reference Guide 5.2.1.2 Checking Drawer Status You can get drawer status by using Status API. Below is examples of program which checks the drawer status. 'get the current printer status rtn = BiGetStatus(m_hApi, getstatus) If rtn < 0 Then ErrMsg (rtn) íError handling Exit Sub End If If (getstatus And ASB_DRAWER_KICK) = ASB_DRAWER_KICK Then MsgBox("Drawer is opened") íPin No.
Below are examples of programs that use events to check if the drawer has been opened or closed. [Main Program] Global DrawerFlag As Boolean If Not OPOSCashdrawer1.DrawerOpened Then DrawerFlag = True OPOSCashdrawer1.OpenDrawer While (DrawerFlag = True) íThis part uses timer management to check the status of DrawerFlag. DoEvents Wend End If [Event Management] Private Sub OPOSCashdrawer1_StatusUpdateEvent(ByVal As Long) If Data = False Then DrawerFlag = False End If End Sub 5.2.
TM-U220 Technical Reference Guide 2. User NV memory There is free area in the NV memory that the user can use. You can use this free area for notations, to write other character information, or for many other purposes. The data remains after you turn off the power. Use ESC/POS commands to read and write this data. The following are examples of purposes.
5.4 NV Bit-image Printing This printer has “NV Bit-image“ Function. This function provides printing bit-image (e.g. a shop logo.) This function is available for any control method (APD, OPOS, ESC/POS command.) EPSON provides a tool, “TMFLogo” that enables registration of a bitmap image in the NV memory of an EPSON TM series printer. The bitmap image in the NV memory can be printed with the printer by using each control method. NV Bit-image Printable Size Printing method Less than paper width.
TM-U220 Technical Reference Guide The available NVRAM size for the TM-U220 is 128KB. 5.4.2.2 LetterQuality It is possible to change the speed and quality of a bitmap by using the XXXLetterQuality property. RecLetterQuality = TRUE ‘print Receipt’s bitmap in quality mode. RecLetterQuality = FALSE ‘print Receipt’s bitmap in speed mode. 5.4.2.3 Setting of printing position by escape sequence POS Printers support escape sequences that can be treated as printing data.
5.5 Printing for journal used This printer can print on carbon paper (original + 1 copy.) This is available to use for journal. When you use this printer “Type A” model, you can take up the copied paper with Auto take-up unit. If you use this printer “Type B“ model, you can cut each a receipt and the copy at same time. A special control isn’t required to use carbon paper; you can treat it as same as normal paper.
TM-U220 Technical Reference Guide 5.7 FAQ List The questions shown in the list below begin with “Q” and their replies with “A.” 1. Sentences beginning with “Q” provide information relating to a question or problem. 2. The instructions described in the “A” sentence answer the question or solve the problem. 5.7.1 Q. Drawer kick does not operate properly. 5.7.1.1 A. Drawer specifications differ, depending on the manufacturer and the part number. We recommend to use a Drawer that is made by EPSON.
5-12 Application Development Information Rev.
TM-U220 Technical Reference Guide Chapter 6 Notices for Replacement of the TM-U210/TM-U300 TM-U220 is designed to smoothly replace the TM-U210/TM-U300. This section gives answers to your questions. 6.1 For Replacement of the TM-U210 When you replace TM-U210 with the TM-U220, you have to set the memory switch [MemSW8-5: OFF (default)] and [MemSW 8-8: OFF (default)] to get the same statas provided by the TM-U210. See “6.1.6 Provided statuses (6-5 page)” for details. 6.1.
6.1.1.2 Characters TM-U220 has almost the same character spec as the TM-U210. Therefore, the TM-U220 can print the same contents as the TM-U210 without adjusting any original control sources. Character spec TM-U210 (Type A,B,D) TM-U220 (Type A,B, D) Character par line (CPI) Font A (9 x 9) 33 (35) cpl 33 (35) cpl Font B (7 x 9) 40 (42) cpl 40 (42) cpl Kanji (16 x 16) 25 (22) cpl 25 (22) cpl Font A (9 x 9) 1.6 x 3.1 1.6 x 3.1 Font B (7 x 9) 1.2 x 3.1 1.2 x 3.1 Kanji (16 x 16) 2.7 x 2.7 2.
TM-U220 Technical Reference Guide Paper feed direction TM-U210 (Type A, B, D) Manual cut position line 22.1 mm Print start position line Paper feed direction Manual cut position line 34.9 mm Auto cut position line TM-U220 (Type A, B) (When using 76mm roll paper) 27 mm Print start position line Paper feed direction TM-U220 (Type D) (When using 76mm roll paper) Manual cut position line 22.1 mm Print start position line These values are reference values 6.1.
6.1.3 Dimensions Some dimensions of the TM-U220 are smaller than those of the TM-U210 except Type D. Therefore, the TM-U220 Type A and B printers can be installed in the same space as the TM-U210 Type A and B. Dimensions (W x D x H) (Unit: mm) TM-U210 TM-U220 Type A 160 x 295 x 160 160 x 286 x 158 Type B 160 x 248 x 150 160 x 248 x 139 Type D 160 x 248 x 133 160 x 248 x 139 See “1.7.1 External Dimensions and Mass (1-17 page)” for details. 6.1.
TM-U220 Technical Reference Guide 6.1.4.2 Effect on the application in the condition of release full state The time from buffer full to releasing full state becomes longer than for the TM-U210. There is a possibility that the application gets a time-out. For countermeasure, Memory switch [MemSW8-7] assigned for selection of buffer-full release condition, 256 bytes (default) of 138 bytes. Therefore when the time-out occurs, set the memory switch [MemSW8-7] on. 6.1.
See the next tables for the behavior. The status behavior is as following two tables. U210 Printer status bit Off-line Paperout LED Operation when paper-end Waiting on-line recovery Cover open 1) Paper end occurs. OFF line ON OFF -- 2) Operator opens the cover for setting a paper roll. OFF line ON OFF -- 3) Operator installed paper roll then closed cover. OFF line OFF waiting on-line recover -- OFF -- 4) Type B,D: Operator pressed FEED SW when paper out LED blinks.
TM-U220 Technical Reference Guide You don't have to be afraid when you use the printer with OPOS or Advanced Printer Driver (APD) and you set the memory switch as [MemSW 8-5: OFF], [MemSW 8-8: OFF]. Because the status behavior normally doesn't affect your application.
6.1.8.4 Memory Switch and memory switch setup mode The TM-U220 has a Memory switch which is a software DIP switch. The memory switch setup mode is for adjusting the memory switches by printer only (No host PC needed.) See “3.4.3 Memory Switches (3-19 page)” and “3.4.4 Memory Switch Setup Mode (3-21 page)” for detail. 6.1.9 Driver compatibility This section informs you the compatibility and notices for replacing. 6.1.9.1 Advanced Printer Driver The TM-U220 has compatibility with the TM-U210 in APD.
TM-U220 Technical Reference Guide 6.2.1.1 Printing area The TM-U220 has almost the same printing area as the TM-U300 as shown in the following table and figures. Therefore, the TM-U220 can print same contents as the TM-U300 without any adjustment of original control sources. Printing areaItem TM-U300 (Type A,B, C, D) TM-U220 (Type A,B, D) (when 76mm paper using) Print width 63.5mm (200dots, 400 position) 63.34mm (200dots,400position) Left margin 6mm 6.8mm Right margin 6.5mm 5.
6.2.1.3 Cutting position from print start position The TM-U220 has almost the same distance from the auto cut position to the print start position as the TM-U300. Therefore the top margin is same as previous one when you replace the TM-U300 with the TM-U220 with an autocutter. In other cases, please refer the table and figures below.
TM-U220 Technical Reference Guide 6.2.2 Cutting Method The TM-U220 (Type A, B) has auto cutting with partial cut or full cut method. These methods are switched by user operation. (See “3.4.7 Select Autocutter action (3-28 page)” for detail.) However, the partial cut method is little different from the TM-U300. The TM-U300 can select the partial cut method from Driver or ESC/POS command control. There are two partial cut methods, one is three points left method, the other is one point left uncut. 6.2.
The “Byte number from buffer full to release full state” is larger than TM-U300. It is for improvement. However, you should pay attention to the following: 6.2.4.1 Effect to the application when condition of buffer full is changed The time from buffer empty to buffer full becomes longer. However, there are no cases in which the host PC watches the time; therefore, there should be no problem. 6.2.4.
TM-U220 Technical Reference Guide 6.2.6 Provided statuses and detectors TM-U220 has same statuses as TM-U210/TM-U300. In addition, the TM-U220 has new statuses. The following sections describe them. 6.2.6.1 Newly added Status The following statuses have been added for the TM-U220. About the use of these statuses , See “5.1 Various Status Categories (5-1 page).” ❏ Roll paper cover open/close status ❏ Roll paper near-end status (When equipped with a near-end detector [Factory option]) 6.2.
6.2.9.1 Advanced Printer Driver The TM-U220 does not have compatibility with the TM-U300 in the Advanced Printer Driver (APD). Therefore, the TM-U300 APD can’t drive the TM-U220. However, you can print almost the same output as the TM-U300 APD by using the TM-U220 APD. The print margin is little different from original output. See “6.2.1 About Printing format compatibility (6-8 page)” for the difference. 6.2.9.2 OPOS TM-U220 does not have compatibility with the TM-U210/TM-U300 in OPOS.
Rev. D Print specification ERC-38 (P), (B/R) 2.7 x 2.7 Kanji (16 x 16) Ribbon cassette 1.2 x 3.1 Font B (7 x 9) Code page 0 to 5 1.6 x 3.1 25 (22) cpl Kanji (16 x 16) Font A (9 x 9) 40 cpl Font B (7 x 9) Character configuration Character width 33 cpl Font A (9 x 9) possible 2 color printing Character per line Approx. 3.5 lines/sec.(40 column, 16cpi) Print speed ERC-38 (B), (P), (B/R) Code page 0 to 8, and 19 to 26 2.7 x 2.7 1.2 x 3.1 1.6 x 3.
A-2 Comparison table for TM-U220/U210/U300 Rev. D Paper specification Paper supply functions Yes (Option for type C, D) Friction feed Default 4.23mm(1/6 inches): changeable by command 25 lines/sec Validation detector Paper feed method Paper feed length Paper feed speed Validation paper Number of copies Type C, D only Not supported <== Original + 2 copies (type D only) Original + 2 copies (at temperature approx.
Rev. D 36mm 26mm (type A, B) A/C position to print start position Manual cut position to print start position Print area Internal buffer Full cut / partial cut; selectable by command Autocutter (type A/B) User NV memory NV bit image No No Multi-language model No Multi-language model ANK model No 512 bytes / 40 bytes; selectable Multi-language model ANK model 1K bytes / 40 bytes: selectable Approx. 6.5mm Right margin ANK model (6mm) Left margin Receive buffer 63.
A-4 Comparison table for TM-U220/U210/U300 Rev. D Horizontal (max. slant 15 degree) and Wall hanging possible.(Type B, D) Install Horizontal (max. slant 15 degree) V-0 Type D; 160 x 248 x 133 Type D; 158 x 235 x 125 V-0 -- Type C; 158 x 295 x 145 PA-6513 Type B; 160 x 248 x 150 PA-6513 or PB-6513 Australia PA-6511 Type B: 170 x 253 x 148 PA-6511 or PB-6511 For Europe (U.K.
TM-U220 Technical Reference Guide Appendix B How to Install the Printer on a Wall with the WH-10 WH-10 is a option for the TM printer series, with it you can install a TM-U220 on a wall. This section describes how to install wall hanging TM-U220. See the “WH-10 installation Manual“ for details. Note: The printer has a “right side up printing“ mode for the printer installed on a wall. See “What is “Right side up printing“ ?” on page 5-10. B.1 The Procedure B.1.
B.1.2 Unpacking Open the package and confirm that it contains all of the parts listed in the illustration. If any parts are missing or damaged, please contact your dealer for assistance. 1 1 4 2 4 3 3 1 1 4 2 wall-mount (note: screws for wall-mount not included; see the installation section.) installation manual 2 3 4 3 2 brackets (2 pieces) screws for brackets (3×12) (4 pieces) control panel sheets Please attach the appropriate sheet.
TM-U220 Technical Reference Guide B.1.3.1 Installing the wall-mount CAUTION: The weight of the printer is approx. 2.5 kg for the TM-U220 Type B, and approx. 2.3 kg for the TM-U220 Type D. In order to insure that the wall-mount can properly support the weight of the printer, please secure it with screws appropriate to the type of wall the wall-mount is installed on. A screw with 4 mm diameter and length of 12 mm or more is recommended. The thickness of the wall should be 10 mm or more.
2. Loosen the detector adjustment screw a little bit by using a tool such as a coin and then loosen the screw gently by hand as until it stops. It must not be removed completely. detector adjustment screw 3. Remove the two screws of the roll paper guide. roll paper guide For a model that does not have a roll-paper near-end detector , jump to step 6. 4. Rotate the detector lever on the roll paper guide to change its direction.
TM-U220 Technical Reference Guide roll paper holder roll paper guide 76 mm 70 mm 58 mm 7. Align the hole on the roll paper holder for hanging bracket with the dowel on the roll paper guide. (For a model that needs a change of paper width, the hole to be used will be different to match your roll paper width.) Putting the screw (3×6) in the hole on the roll paper holder for hanging bracket makes it easier for you to tighten the screw in the next step.
9. Tighten the screw (3×10) to fix the roll paper holder for hanging bracket and the roll paper holder. 10. Check that the brake arm is up as shown in the illustration below. brake arm CAUTION: Do not move the brake arm until the roll paper holder for hanging bracket is attached onto the base frame. Otherwise the arm part will be damaged. 11. Insert the dowel of the cam into the hole of the platen frame. dowel hole platen frame B-6 How to Install the Printer on a Wall with the WH-10 Rev.
TM-U220 Technical Reference Guide 12. While you make sure the pin of the brake arm is in the groove on the inner side of the cam, rotate the cam along with the surface of the platen frame in the direction indicated by the arrow until it clicks into position. pin of brake arm 13. Close the printer cover. Note: When closing the cover, push the middle of the printer indicated by the circle in the illustration below. Rev.
14. Turn the printer over and then put it on a packing box as a platform horizontally. Fold this part inside and insert it into holes to assemble the package. 15. See the “Installing the Brackets” section for attaching the brackets. Removing the cam While you push the cam through the hole on the platen frame with a pointed tool such as tweezers, rotate the cam in the upper direction to remove it. B.1.6 Installing the brackets Four different sets of screw holes are found on each bracket.
TM-U220 Technical Reference Guide B.1.7 Mounting the printer on the wall CAUTION: When mounting the printer, make sure that the wall-mount is securely fastened to the wall. When the brackets are attached properly for the TM-U220B/U220D, the printer’s operation panel will be on the top and the connector side on the bottom. If this is not the case, please see the installing the brackets section and reattach the brackets in the proper position.
B.2 Exterior Overviews B.2.1 TM-U220 (Type B) 146 14 5 B-10 How to Install the Printer on a Wall with the WH-10 Rev.
TM-U220 Technical Reference Guide B.2.2 TM-U220 (Type D) 146 14 5 Rev.
B-12 How to Install the Printer on a Wall with the WH-10 Rev.
TM-U220 Technical Reference Guide Appendix C Character Code Table C.1 Page 0 (PC437: USA, Standard Europe) (International character set: when U.S. is selected.) Rev.
C.2 Page 1 (Katakana) C-2 Character Code Table Rev.
TM-U220 Technical Reference Guide C.3 Page 2 (PC850: Multilingual) Rev.
C.4 Page 3 (PC860: Portuguese) C-4 Character Code Table Rev.
TM-U220 Technical Reference Guide C.5 Page 4 (PC863: Canadian-French) Rev.
C.6 Page 5 (PC865: Nordic) C-6 Character Code Table Rev.
TM-U220 Technical Reference Guide C.7 Page 6 (Hiragana) This page is available on the Japanese model only. Rev.
C.8 Page 7 (One-pass printing Kanji characters) This page is available on the Japanese model only. C-8 Character Code Table Rev.
TM-U220 Technical Reference Guide C.9 Page 8 (One-pass printing Kanji characters) This page is available on the Japanese model only. Rev.
C.10 Page 16 (WPC1252) C-10 Character Code Table Rev.
TM-U220 Technical Reference Guide C.11 Page 17 (PC866: Cyrillic #2) Rev.
C.12 Page 18 (PC852: Latin2) C-12 Character Code Table Rev.
TM-U220 Technical Reference Guide C.13 Page 19 (PC858: Euro) Rev.
C.14 Page 20 (Thai character code 42) This page is available on the Thai model only. C-14 Character Code Table Rev.
TM-U220 Technical Reference Guide C.15 Page 21 (Thai character code 11) This page is available on the Thai model only. Rev.
C.16 Page 22 (Thai character code 13) This page is available on the Thai model only. C-16 Character Code Table Rev.
TM-U220 Technical Reference Guide C.17 Page 23 (Thai character code 14) This page is available on the Thai model only. Rev.
C.18 Page 24 (Thai character code 16) This page is available on the Thai model only. C-18 Character Code Table Rev.
TM-U220 Technical Reference Guide C.19 Page 25 (Thai character code 17) This page is available on the Thai model only. Rev.
C.20 Page 26 (Thai character code 18) This page is available on the Thai model only. C-20 Character Code Table Rev.
TM-U220 Technical Reference Guide C.21 Page 254 (Blank page) Rev.
C.22 Page 255 (Blank page) C-22 Character Code Table Rev.
TM-U220 Technical Reference Guide C.23 International Character Sets Country ASCII code (hexadecimal number) U.S. France Germany UK Denmark I Sweden Italy Spain I Japan Norway Denmark II Spain II Latin America Korea Rev.
C-24 Character Code Table Rev.
TM-U220 Technical Reference Guide Appendix D Power Supply Unit D.1 AC Adapter C This power supply unit can be used with the TM-U220 ANK model only. When you use any other model of the TM-U220, please use PS-180. D.1.1 Case specifications ❏ Size: 54 mm(D) × 114 mm(L) × 36 mm(H) {2.13 (D) × 4.49 (L) × 1.42" (H)} (excluding projections) Refer to the figure below. ❏ Mass: Approx. 0.4kg (excluding the AC cable) ❏ Material: Flame-resistance grade: V0 ❏ Color: Black (matte) Case specifications Rev.
D.2 PS-180 This power supply unit can be used with all models of the TM-U220. D.2.1 Case specifications ❏ Size: 68 mm(D) × 136 mm(L) × 32 mm(H) {2.68 (D) × 5.35 (L) × 1.26" (H)} (excluding projections) Refer to the figure below. ❏ Mass: Approx. 0.4kg (excluding the AC cable) ❏ Material: Flame-resistance grade: V0 ❏ Color: Black (matte) Case specifications D.2.
EPSON SEIKO EPSON CORPORATION Printed in Japan
