TM-T90 User’s Manual / Bedienungsanleitung Gebruikershandleiding / Manuel d’utilisation Manual do utilizador / Manual del usuario Manuale dell’utente 402020601
Printer Parts paper roll cover cutter cover 1 2 5 control panel 3 power switch 4 cover open lever DIP Switch Tables Serial SW Function Parallel ON OFF SW Function 1-1 Power switch function Disabled Enabled 1-1 Power switch function Disabled 1-2 Interface condition selection by DIP switch by memory switch 1-2~ Reserved 1-8 Fixed to Off. 1-3 Handshaking XON/XOFF DTR/DSR 2-1 Fixed to Off.
English All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein.
English Safety Precautions This section presents important information intended to ensure safe and effective use of this product. Please read this section carefully and store it in an accessible location. WARNING: Shut down your equipment immediately if it produces smoke, a strange odor, or unusual noise. Continued use may lead to fire. Immediately unplug the equipment and contact your dealer or a SEIKO EPSON service center for advice. Never attempt to repair this product yourself.
English Caution Labels WARNING: Do not connect a telephone line to the drawer kick-out connector; otherwise, the printer and the telephone line may be damaged. CAUTION: The thermal head is hot. Control Panel LEDs and Button POWER LED Lights when the power is on, and is off when the power is off. ERROR LED Off when the printer is online, lights when the printer is offline, and flashes when an error occurs. PAPER OUT LED Lights when roll paper is nearly out. FEED button Feeds the roll paper.
English Power Switch and Power Switch Cover The power switch is on the front of the printer. Press it to turn on the printer, and press and hold it for more than 3 seconds to turn off the printer. Power Switch Cover You can use the enclosed power switch cover to make sure that the power switch is not accidentally pressed. Peel off the backing tape and press the cover into place to install it in the position shown in the illustration below.
English Unpacking The following items are included for the standard specification printer. If any items are damaged, contact your dealer.
English When you install the printer vertically, attach the rubber feet and control panel label as shown in the illustrations below. Note: To hang the printer on the wall, see the Wall Hanging Bracket Set Installation Manual provided with the WH-10 for instructions. Installing the Paper Roll Note: Be sure to use paper rolls that meet the specifications. 1. Open the paper roll cover, using the cover open lever. 2.
English Note: Be sure to close the cover completely by pushing down on the middle of the cover. Troubleshooting ERROR LED on or flashing ❏ Check to see that the paper roll cover is closed and check the PAPER OUT LED. Close the cover or replace the paper if necessary. ❏ If the printer has been printing a lot, the head may be hot. Wait for the head to cool. Printing will resume automatically. ❏ If the autocutter is jammed, turn the printer off and then back on.
English cover upward. After removing the cutter cover, use a ballpoint pen or tweezers to turn the knob in the direction indicated by the arrow until you see a triangle in the opening. Cleaning the Print Head CAUTION: After printing, the print head can be very hot. Be careful not to touch it and to let it cool before you clean it. Do not damage the print head by touching it with your fingers or any hard object.
English Connecting Cables To connect cables, first remove the bottom of the cover as shown in the illustration. To place the cables, first break off by hand any of the three portions indicated by circles in the illustration (the other portion is on the right). Then put the cables through the holes and replace the bottom of the cover.
English . TM-T90 Specifications Print method Thermal line, 0.141 mm/dot × 0.141 mm/dot (180 dpi × 180 dpi) Print font 12 × 24/9 × 17 Columns 12 × 24/9 × 17: 42/56 (when paper roll width is 80 mm) Print width 72.2 mm {2.84"}, 512 dot positions (when paper width is 80 mm) Character size (W × H) 12 × 24: Normal/double-high/double-width/quadruple 1.692 × 3.384 mm/1.692 × 6.768 mm/3.384 × 3.384 mm/3.384 × 6.768 mm {0.07 × 0.13"/0.07 × 0.27"/0.13 × 0.13"/0.13 × 0.
