W i d e Fo r m at Pr i nter Ter i o s t ar LP-10 3 0 S er i e s Multifunction Model LP-1030-MF Printer Model LP-1030 Quick Reference Guide To operate your Printer correctly, read this manual carefully before use. After reading the manual, keep it in a place where you can access it when required.
Preface Your Printer is a Teriostar LP-1030 Series Wide Format Printer. This manual describes the basic operation methods for both the LP-1030 and LP-1030-MF models. For more detailed information, see the User's Manuals on the supplied CD-ROM.
Turning the Power On/Off Power On 1 Power Off 2 1 Press down for 1 sec. or longer 2 Mode Buttons zzCOPY button MF Changes to copy mode, and the lamp at the button's left lights up. For more details, see the separate User's Manual for Multifunction Printer Operation. zzSUBMIT button MF Changes to submission mode, and the lamp at the button's left lights up. For more details, see the separate User's Manual for Multifunction Printer Operation.
Replacing the Paper 1 5 2 6 3 7 4 4
TT Replacing the Paper 8 60 cm (23.
Replacing the Toner Cartridge 1 3 4 x10 x10 5 2 6 6
TT Replacing the Toner Cartridge 7 8 Disposing of Empty Toner Cartridges Put the used toner cartridge into the bag provided in the box of the new toner cartridge, and dispose of it according to the local regulations.
Replacing the Waste Toner Bottle 1 x10 2 3 ① ② 4 8
TT Replacing the Waste Toner Bottle 5 6 7 ① ② Disposing of Used Toner Bottles Dispose of the waste toner bottle according to the local regulations.
Replacing the Charger Unit 1 5 Press down for 1 sec.
TT Replacing the Charger Unit 8 12 TIP The charger unit can be installed in either direction. If lines or other defects appear on the printout, inverting the charger unit right and left sides may solve the problem.
Replacing the Process Cartridge 1 6 Press down for 1 sec.
TT Replacing the Process Cartridge 12 15 13 16 17 14 ① ① ② ② ③ 18 ③ 13
Part Names Front Side Multifunction Model Scanner cover Original output guide Document table Latch lever Filter cover Drawer for roll 1 Waste toner door Drawer for roll 2 Printer Model Latch lever Filter cover Drawer for roll 1 Waste toner door Drawer for roll 2 14
TT Part Names Rear Side Multifunction Model Printer Model Toner door Toner door Rear door Rear door Process cartridge drawer Fuser unit drawer Paper outlet cover 15
Paper Jams The door requiring action is displayed, in accordance with the paper jam location. Open the specified door and take the appropriate action to remove the paper jam.
TT Paper Jams Paper jam in the rear door 1 3 4 2 17
TT Paper Jams Paper jam in the Fuser unit 1 3 2 When you cannot pull out the paper easily: ② ① 18
TT Paper Jams Paper jam in a roll paper drawer or front door 3 1 4 2 ロール紙の交換 Replacing Roll Paper ᤶ㒌ो 用紙カット位置 Paper Cut Position ߛ㒌ԡ㕂 5 19 1 2 3 4 5 6 7
TT Paper Jams 6 Original jam 7 1 8 2 3 20 MF
TT Paper Jams 4 5 21
Copying MF Press COPY Set the original Position the original facing down. Set it in the Printer aligned with the original width guide. The inserted original is automatically pulled into the Printer, and set.
Importing Images (Documents) to a Computer MF 1 Double-click TerioStation. 2 Click the Scan tab. 3 Click Save Folder. 4 Select the destination folder to save the scanned data. Click OK. 5 Click Scan.
TT Importing Images (Documents) to a Computer MF 6 Click Preferences. 7 Input the Printer IP address in the Assign host name/IP address field. Click OK. 8 Set the scan conditions, and then click Scan. 9 Load the original. Important If "Scanner is operating in another mode" is displayed, press SCAN on the operation panel. If "Color processing is not supported because the scanner being used is a dedicated monochrome device" is displayed, you cannot scan in color mode.
Operating the Printer from a Computer 1 Start the web browser and enter "http://(IP address set on the Printer)" in the address field. Press Enter. 2 Click English. 3 Click an item from the left menu to check the settings or Printer status.
Troubleshooting Automatic Paper Cutting After a Certain Time When an Error Message Appears Take the action specified by the panel message. Or see the User's Manual for Basic Printer Operation, Chapter 5. Set Top Cut Timer in the Printer Engine menu. Menu Smears on a Printout Replace the process cartridge. (& page 12) Printer Engine Changing the Time Until Power Save Mode Roll 1 Top Cut Timer Set Time Before Power Save in the Printer Engine menu.
TT Troubleshooting Automatic Paper Cutting After Opening and Closing a Door Wrinkles on Tracing Paper Set Humidity for Tracing Paper to High Humidity in the Printer Engine menu. Set Top Cut at Door Open to On in the Printer Engine menu. Menu Menu Printer Engine Printer Engine Humidity for Tracing Paper Top Cut at Door Open High Humidity On Selecting Paper to Match the Print Data Changing the Print Density Select Optimal at Paper Supply Mode. Set the Print Density in the Printer Engine menu.
TT Troubleshooting Missing Print or Slow Data Reception Change the driver settings. 1 4 Click Change in the operation mode of the driver. 5 Change the output process selection from Process with Printer to Process with Computer. Click OK. 6 Click Apply. In Start Menu, open Devices and Printers. 2 Right-click the SII LP-1030 icon, and then click Printing Preferences. 3 Click the Options tab.
TT Troubleshooting 7 Click OK. 8 Print. If the problem persists: 1 Perform steps 1 to 4 and open Driver Operation Mode. 2 Set the resolution of the printer driver to 200dpi or 100dpi. Click OK. If the symptom persists, perform the following setting operation.
TT Troubleshooting 3 Click Apply. 4 Click OK. 5 Print. The User's Manuals and driver are on the supplied CD-ROM.
Service Representatives SIIT offers support to ensure you get the most from your Teriostar LP-1030 Series Printer. For details, contact your dealer or nearest service representative. http://www.seiko-i.com/ Disposal Method Dispose of the used toner cartridges and waste toner bottles according to the local regulations.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
