U00107692700 Quick Reference Guide Black-and-White Raster Plotter LP-1020 LP-1020L Network Multi Function Plotter LP-1020-MF LP-1020L-MF
Introduction Thank you for purchasing our LP-1020/LP-1020L Black-and-white Raster Plotter and LP1020-MF/LP-1020L-MF Network Multi-Function Plotter. This manual explains the basic operations of LP-1020/LP-1020L and LP-1020-MF/LP1020L-MF. For details, refer to the respective PDF data saved in CD-ROM. The DSCAN format described in this manual as well as DSCAN that appears on the operation display are for only customers in Japan. Table of Contents 1 LP-1020/LP-1020L ...........................................
● Names and functions of each part LP-1020/LP-1020L Front / right side/rear side Toner cover Finished drawing outlet Manual feed drawer (door 4) Waste toner door Roll 1 drawer (door 1) 1 Roll 2 drawer (door 2) LP-1020/LP-1020L Control panel Top cover (door 6) Fixation door (door 7) Manual paper feeding guide (door 8) Manual feed inlet Paper feed knob Paper flange Main power switch USB interface connector Power cord Parallel interface connector Ethernet interface connector Cutter door inside (
Control panel ➁LCD ➃Power key ➀LEDs ➂Keys Number 1LED's 2Display 3Keys 4Power Name Function Error lamp (red) Indicates the presence or absence of errors. On: Error present Off: No error present Toner lamp (green) Indicates the amount of remaining toner. On: There is sufficient toner. Flashing: Toner is running low. Off: There is no toner (plots cannot be produced without replenishment.) Waste toner lamp (green) Indicates the toner waste bottle replacement time.
● Turning the power on and off LP-1020/LP-1020L Power on ON/OFF I N I T I A L I Z I NG WA I T A MOMEN T When you first turn on the power after purchasing this device, a guidance display prompts you to set the panel's display language. If this setting has already been completed, this message is omitted. Main power switch A “PRINT READY” message indicates that the device is functioning normally.
● Set menu LP-1020/LP-1020L Menu structure Press to set the device offline before performing setting operations. Select a menu using the , keys and press the key to enter each menu. Changed parameters are saved in non-volatile memory and are not lost when the power is turned off.
Paper Function Protocol POWER SAVE Sets the time until the device enters the power saving mode. EDGE CUT TIMER Sets the data standby time to automatically have the paper roll end cut before plotting using data received after a data standby status has continued for a while. DOOR OPEN CUT To plot the first data after the roll door is opened and ¥closed, sets whether to start plotting after the end of the roll paper is automatically cut. DENSITY Adjusts the printing density. TRACE PAP.
● How to set the paper rolls LP-1020/LP-1020L Replacing paper rolls ◆How to detach the paper rolls Detach and replace a paper roll when the device has run out of paper rolls or when you change the paper roll size on type. When the paper is used up during printing, the Error lamp will turn on and the LCD will display the following message: Example: Pull out the Roll 1 or Roll 2 drawer. Use your fingers to grasp the handle in the center of the drawer and pull the drawer out gently.
◆How to attach the paper roll Hold the paper roll so that the end of the paper is positioned at the bottom facing the back of the device. Then align the paper flange to the depressions in the flange guide and gently insert the flange in place. ◆ The paper flange ends do not have a designated right or left side. You can attach them to either side. Attach the paper flange to a paper roll.
Caution Note ◆ After closing the paper roll drawer, wait until the “WAIT A MOMENT” message disappears before opening the paper roll drawer again. As the device initiates a paper detection just after the paper roll drawer is closed, so opening the paper roll drawer during this operation may cause a paper jam. ◆ Take care not to hurt yourself and damage the device when handling the cutter. ◆ Handle the cutter blade with care so that you do not break it.
● Troubleshooting LP-1020/LP-1020L If a paper jam occurs, the ERROR lamp lights and the following error message appears on the LCD. According to the paper jam point, the door number from which the corrective measure starts is displayed (plural numbers may be displayed as shown left). In case of a paper jam, open the door of the displayed door number, and take a corrective measure.
Symptom and corrective measure ◆Items to be checked Symptom No power Failure to start or operate correctly Failure to plot Failure to plot transmitted data immediately Frequent paper jam Items to be checked Corrective measure Power cable connection Plug the power cable into the outlet correctly. Power supply to the outlet Supply the power to the outlet. ERROR lights and LC message display Take appropriate measures according to the error message.
● Names and functions of each part LP-1020-MF/LP-1020L-MF Front / right side/rear side Control panel Scanner exit guide Finished drawing outlet Manual feed drawer (door 4) Waste toner door Roll 1 drawer (door 1) Top door (door 6) Scanner cover Fixation door (door 7) Manual paper feeding guide (door 8) Manual feed inlet Paper feed knob Paper flange Main power switch Power cord Parallel interface connector USB interface connector Toner cover Cutter door inside (door 9) Ethernet interface connecto
Control panel 1 2 WARNING LIGHT 3 4 MENU COPY PRINT MEMORY RESET POWER SAVING DELIVERY FILE REPRINT STOP 5 POWER SCAN STOP ORIGINAL SIZE TONER PROCESS WASTE TONER ORIGINAL TYPE AUTO TEXT/LINE FIXED-SIZE PORTRAIT TEXT/PHOTO FIXED-SIZE LANDSCAPE PHOTO SYNCHRO BLUE PRINT BACKGROUND REMOVAL DENSITY PAPER FEED DARK MANUAL FEED NORMAL LIGHT DATA SCALE x1 FIXED SCALE ORIGINAL NON-PROPORTIONAL SORT SCALE FUNCTION ERROR 6 No.
Name [PROCESS] LED [MANUAL FEED] LED 6 7 8 9 10 Function Indicates the process cartridge replacement time. On: Normal. Flashing: Replacement timing is approaching. Off: Process cartridge is not installed. Indicates whether the paper to be fed manually has been set. On: Paper has been set. Off: No paper. [1], [2] LEDs Indicate whether the paper has been set in the roll 1 and roll 2 drawers respectively. On: Paper has been set. Off: No paper. [DATA] LED Indicates the data receiving status.
● Turning the power on and off LP-1020-MF/LP-1020L-MF Power on Turn on the Main power switch located at the lower-left as seen from the rear of the device. Press the power key located on the control panel of this device (when the main power switch is on). Press the power switch toward the ⎪ symbol (upwards). I n i t i a l i z i ng When you first turn on the power after purchasing this device, a guidance display prompts you to set the panel's display language.
● Set Menu LP-1020-MF/LP-1020L-MF PRINT mode Press the [MENU] key during stand-by or in the PRINT mode and enter OFLINE. The menu message will appear. The setup method and setting items are the same as those of LP-1020/LP-1020L. Refer to page 4. COPY mode ◆Copy function overview Description Sets the original size. Original Type Selects the image type according to the original. Adjust the background color if the original has uneven density. Adjust the density. Adjust the copy density.
DELIVERY mode ◆Delivery function overview ◆Delivery function In the DELIVERY mode of the device, the scanned data can be saved in the delivery host computer connected via network, or the data can be transferred to other computers on the same network. To use the delivery function, plotshare must be installed beforehand in the delivery host computer used and various settings must be made with this application software. Function list Original Size Description Sets the original size.
See “User's Guide, Copy part” for the delivery operation. Input the original. Input the original to the device. Press the [START] key. If the SCAN START or ORIGINAL SET has been set in the system menu, the copy/delivery starts automatically without pressing the [START] key. (For details, see “User's Guide, Plotter Unit.”) FILE mode ◆File Function ◆Screens of file function Change the mode of the device to “FILE,” and the original data is read from a computer connected via network.
● How to input an original/Routine maintenanceLP-1020-MF/LP-1020L-MF How to input an original ◆ Butt the original against the front roller and give it a slack, so Roller Slack that the original can be inserted straight. Adjust the position of the original width guide. Adjust the original width guide to the applicable line according to the original size. Note ◆ If you selected the front reject of the original, set the original, aligning with correct size line.
◆Removing original width guide Remove the scanner exit guide. Lift and pull the guide toward the rear to remove. Close the scanner cover. While supporting the scanner cover with your right hand, release the stopper with your left hand and close the scanner cover slowly. 2 Note ◆ Take care that you pull toward you. Pulling down on the claw could damage the claw.
Cancel the scanning of original To cancel the scanning because of the feed isn’t straight or the original jams, do the following: Close the scanner cover. While supporting the scanner cover with your right hand, release the stopper with your left hand and close the scanner cover slowly. Press the [SCAN STOP] key Press the [SCAN STOP] key on the control panel, and the scanning is then stopped.
● Troubleshooting LP-1020-MF/LP-1020L-MF Copy/scan cannot be performed clearly Q. A. Streaks appear in the copy/scan result • The shading guide or scanner glass is dirty. ➝Clean the shading guide or scanner glass (⇒ page 20). A. Note ◆ Copying/scanning the original stained with the toner, ink, or dust makes the inside of scanner dirty. Remove stains on the original before starting the copy/scan. ◆ When copying/scanning a long original, be careful that the original does not touch the floor.
● Maintenance Panel messages used in this manual refer to those used in LP-1020/LP-1020L. Kanji is also used in LP-1020-MF/LP-1020L-MF to improve the ease of reading messages. Replacing the toner cartridge When there is no more toner availabe, the Toner lamp will go out, the Error lamp will come on, and plotting will no longer be possible. The following message appears on the LCD.
Close the scanner cover. Set the toner cartridge into the main unit. (for LP-1020-MF only) While supporting the scanner cover with your right hand, release the stopper in the middle with your left hand and close the scanner cover slowly. Pull the lever to the right end. At this time, the following message appears on the LCD. After performing the procedure operation, return the lever and remove the toner cartridge.
Remove the toner cartridge and close the cover. Close the scanner cover and attach the scanner exit guide. At this time, the following message appears on the LCD. (for LP-1020-MF only) Follow procedures reject guide. to and attach the original WA I T A MOMEN T Replacing the waste toner bottle When the waste bottle becomes full with waste toner, the Waste toner lamp will go out. The Error lamp will turn on and plotting will not be possible. The following message appears on the LCD.
When you have removed the waste toner bottle, the LCD will display the following message. Attach a new waste toner bottle. 1Insert the mouth of the waste toner bottle onto the waste toner discharge port of the main unit by slightly lifting it. 2Set it onto the bottom surface and position it so that it is stable. SET WAS T E BOT T L E Attach the cap to the waste toner bottle. Attach the cap which you have removed in procedure to the waste bottle containing waste toner.
Note ◆ Until you are ready to install the Process cartridge, do not unpack it and store it in its cardboard container. ◆ Firmly hold the handles on both sides with both hands when handling the Process cartridge. ◆ Take care not to scratch the surface of the photoconductor drum during handling. ◆ With the exception of the handle area, take care to avoid contacting the surface of the photoconductor drum.
Insert the Process cartridge. Replace the filter. To insert the Process cartridge, align the Process cartridge with the angle of the open top cover and insert it in the direction of the alignment arrows (three points/ green). After insertion, remove the protective cover from the top of the cartridge. Pull out the filters toward you and remove, and replace with the two filters contained in the process cartridge packaging box. Maintenance Attach the filter covers and turn ON the device.
8, Nakase 1-chome, Mihamaku, Chiba-shi. Chiba 261-8507, Japan U00107692700 November 2007 Copyright © 2007 by Seiko I Infotech Inc. All rights reserved is a trademark of Seiko Instruments Inc. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
