Cal. 7T04 INSTRUCTIONS (P. BEDIENUNGSANLEITUNG (S. 21) 3) INSTRUCTIONS (P. 39) ISTRUZIONI (P. 57) INSTRUCCIONES (P. 75) INSTRUÇÕES (P. 93) ИНСТРУКЦИИ (P.
English Vous voici l’heureux propriétaire d’une montre quartz analogique SEIKO Cal. 7T04. Pour obtenir d’excellentes performances de cet article SEIKO, veuillez lire attentivement cette brochure que vous conserverez pour toute référence ultérieure. Siete ora in possesso di un orologio SEIKO Analogico al Quarzo Cal. 7T04. Per ottenere i migliori possibili risultati dal Vostro orologio, leggere attentamente le istruzioni di questo manuale prima di utilizzare il Vostro orologio SEIKO analogico al quarzo.
English n TIME/CALENDAR 24-hour, hour, minute, and small second hands Big date calendar n STOPWATCH Measures up to 60 minutes in 1/5 second increments. Split time measurement is available.
English l This watch is designed so that the following adjustments are all made with the crown at the second click position: 1) time setting 2) stopwatch hand position adjustment Once the crown is pulled out to the second click, be sure to check and adjust 1) and 2) at the same time. CROWN Pull out to second click when the small second hand is at the 12 o'clock position. 2. The 24-hour hand moves correspondingly with the hour hand. 3.
English A A t B Press for 2 seconds or longer. * STOPWATCH 1/5-second hand turns a full circle. Press repeatedly to set STOPWATCH 1/5-second hand to the "0" position. * The hand moves quickly if button B is kept pressed. B STOPWATCH minute hand SETTING THE DATE t t CROWN Push back in to normal position in accordance with a time signal. l Before setting the date, be sure to set the time. Date CROWN English STOPWATCH 1/5-second hand Pull out to first click.
English l The stopwatch can measure up to 60 minutes in 1/5-second increments. l After 60 minutes, it will start counting again from "0" repeatedly up to 12 hours. l Split time measurement is available. While the STOPWATCH hands are moving 1. Press Button A to stop the stopwatch. 2. Press Button B to reset the stopwatch.
A B t t English A START STOP SECURITY LOCK OF PUSH-BUTTON A & B RESET START STOP RESTART A A B t A t A t A t Accumulated elapsed time measurement STOP English SECURITY LOCK BUTTON OPERATION (for models with security lock button) Standard measurement Locking Unlocking RESET * Restart and stop of the stopwatch can be repeated by pressing button A.
English To measure the hourly average speed of a vehicle 1 2 Use the stopwatch to determine how many seconds it takes to go 1 km or 1 mile. Ta c hy me ter s c ale indic a te d by STOPWATCH second hand gives the average speed per hour. To measure the hourly rate of operation 1 Ex. 1 STOPWATCH second hand: 40 seconds 2 Use the stopwatch to measure the time required to complete 1 job. English TACHYMETER (for models with tachymeter scale on the dial) Ex.
English l The telemeter can provide a rough indication of the distance to the source of light and sound. l The telemeter indicates the distance from your location to an object that emits both light and sound. For example, it can indicate the distance to the place where lightning struck by measuring the time elapsed after you see a flash of lightning until you hear the sound. l A flash of lightning reaches you almost immediately while the sound travels to you at a speed of 0.33 km/second.
English The miniature battery which powers your watch should last approximately 5 years. However, because the battery is inserted at the factory to check the function and performance of the watch, its actual life once in your possession may be less than the specified period. When the battery expires, be sure to replace it as soon as possible to prevent any malfunction. For battery replacement, we recommend that you contact an AUTHORIZED SEIKO DEALER and request SEIKO SR927SW battery.
English SPECIFICATIONS 1 Frequency of crystal oscillator ................... 32,768 Hz (Hz = Hertz … Cycles per second) 2 Loss/gain (monthly rate) ............................ ±15 seconds at normal temperature range (between 5° C and 35° C) 3 Operational temperature range ................. Between –10° C and +60° C 4 Driving system............................................ Step motor, 3 pieces 5 Display system Time/calendar........................................
