user manual

5
IN CASE OF AN UNUSUAL MOVEMENT OF THE SECOND HAND
50
English
6
TROUBLESHOOTING
51
English
Power Save 1 Power Save 2
State
The second hand stops
pointing at the 15-sec
position.
The second hand stops pointing at
the 45-sec position.
Restriction
on function/
display
・ The hour hand, minute hand, date, and
sub-dial stop.
・ Automatic time adjustment is not
performed.
・
The hour hand, minute hand, date, and sub-dial stop.(Date displays “1.”)
・ Reception is not started even with operation of GPS
signal reception.
・Automatic time adjustment is not performed.
・The indicator hand points to “E.”
Cause
When the watch is exposed to a state without receiving
an adequate light source for 72 hours or longer.
When the watch is in an insuffi cient charging state for a
long time.
Solution
When the watch is exposed to an adequate light
source for more than 5 seconds, or when any
button is pressed, it displays the current time
again after the second hand is rapidly advanced.
① Charge the watch suffi ciently until the charging status is
displayed as the “level position (middle)” or “F (full).”
② Carry out time zone adjustment to set the time.
Power Save 2
※ While the watch is being charged, the second hand moves at “ 5-sec Intervals.” During the “5-sec Interval Movement,” neither the
buttons nor the crown can be operated.
※ If the “ Power Save 2” mode is prolonged, the stored power amount drops and the internal current time information stored will be lost.
Power save function (The second hand stops at the 15-sec position/45-sec position)
When the watch is not exposed to light for a long time, the power save function will work.
The second hand stops at the 0-sec or 5-sec
position (automatic time adjustment)
Automatic time adjustment is being performed.
The indicator hand points to “1.”
It takes up to 1 min to
complete reception.
The second hand is stopped between the 0-sec to 18-sec
positions (Ready for leap second data reception)
The watch is ready for leap second data reception. The second hand indicates the waiting time
until the leap second data reception by minutes.
→ Automatic leap second reception function
P.48
● The second hand stops at the 45-sec position before the
reception is completed (The watch enters the power save 2
state)
・ If GPS signal reception is performed under low
temperatures (0°C or less) in a state where the charging
capacity and/or charging effi ciency are lowered, the reception will be stopped, and the watch may enter
the power save 2 state.
If this occurs frequently, consult the retailer from whom the watch was purchased.
GPS signal reception consumes a significant amount of energy. Keep in mind to charge the watch
regularly by expose to light.
・ When using the watch again under a condition in which the watch is able to receive radio signals, receive
radio signals to set the time.
・When adjusting the time, the date will be accordingly adjusted.
● Reception is not started even with operation of GPS
signal reception (time zone adjustment/manual time
adjustment).
・Check the indicator hand position.
● Reception is not possible even with operation of GPS signal
reception (time zone adjustment/manual time adjustment)
(The reception result is displayed as “N.”)
・ove to a place where GPS signals can be easily received.
When the watch is unable to receive GPS signals
Manual time/date setting (Adjust the time under a condition in which the watch is unable to receive GPS signals)
Points to be checked
When the watch does not start receiving or is unable to receive GPS signals even with operation
of GPS signal reception, the following can be considered.
Manual time/date setting
When a problem cannot be solved even by carrying out the “ Points to be checked,” or time is
gained or lost under a condition in which the watch is unable to receive GPS signals and the watch
is unable to receive GPS signals continuously, set the time and date manually.
Reception
is not
allowed
Indicator
display
Charging status
In-fl ight mode（
）
E (low)
Display
Solution
Charge the watch by
expose to light until the
indicator hand points
to the “level position
(middle)” or “F (full).”
Reset the in-
fl ight mode（
）
→
P.42
Continued on the following page